I have a gateway desktop with a usb wireless card , I've tried two different ones netgear and linksys, but same problem. I can connect to interenet but no gateway is seen on ipconfig on comand line. limted connection it;s says. I've try alot of things but nothing seems to work.
View 3 RepliesMy father gave us an old Gateway computer for the kids to use for homework. We have a Kodak ESP Office 2170 series wireless printer. How can we connect the 2, so they can print their homework out? I've downloaded the software but it won't detect or connect. Is the only way to use the printer , a USB cord?
View 1 Replies View RelatedMy Gateway GZ7112 suddenly decided it would not connect to the internet when plugged into any of the 4 ports on the router (tried 2 routers), But will connect just fine when plugged into a switch which is connected to the same router?
View 6 Replies View RelatedNew hardware here, requesting a bit of your knowledge, We are tryingin to setup a simple gateway to gateway VPN
HomeA Has an RV016 with a public static IP
Local Group Security Gateway type is IP Only with the IP
Local Security Group Type is Subnet, with the local IP class 192.160.0.0
Remote Security Gateway Type: Dynamic + Email
Email address some@emailaddress.com
Remote Security Group Type: Subnet
IP Address 192.168.1.0
IPSec Setup as default with nice password.
HomeB has an RV082 with a dynamic ADSL link
Local Group Security Gateway type is DynamicIP +Email
Email address some@emailaddress.com
Local Security Group Type is Subnet, with the local IP class 192.160.1.0
Remote Security Gateway Type: IP Only
Remote Security Group Type: Subnet
IP Address 192.168.0.0
IPSec Setup as default with nice password.
The idea is for HomeB which has a dynamic IP, to reach HomeA, which has a static IP and connect. But they just wont. I have not clue what's wrong, I followed the instructions, maybe i miss interpreted something. I could share the VPN logs for both., Im getting a lot of errors there.
How to block facebook from gateway computer
View 3 Replies View RelatedI would like to know what ip addresses I should see in this table. Shouldn't my default gateway IP have the same mac address as my computer or router? There are 2 different ip address/mac addresses from different a ISP than mine. I have a cisco DPC3825..I suspect a someone is spoofing my DNS.
View 4 Replies View RelatedI am trying to change the password on my D-Link router. So i typed ipconfig into cmd and the default gateway i get is 169.234.95.I have tried what used to work at home such as 192.168.0.1 and all of those.
View 9 Replies View Relatedcannot connect to my default gateway 192.168.1.1 frustrating.
View 1 Replies View RelatedI have a gateway with windows 7 and was working fine and a couple of weeks ago it will no longer connect to the internet. I have always used the wifi connection. The wifi signal is a orange computer and on my other computer when it is working it is typically green, so I am not sure what this orange color means, if anything.
View 4 Replies View RelatedLaptop has been connecting to internet for years. Originally using wireless Linksys router but wireless card in laptop stopped working. Have been connecting via Ethernet connection for over a year. All of a sudden, cannot connect to internet via Ethernet connection. Laptop connects fine using wireless mobile card (Verizon) with 75.x.x.x address.Using same Ethernet connection,another laptop connects fine (69.x.x.x address)Network status on "broken" laptop shows "Unidentified Network Access: Local Only Ethernet adapter has 169.x.x.x address when connected to cable modem (Roadrunner) with no default gateway.Tried to release/renew IP but get message "The requested operation requires elevation." I am running under admin account.
Sys Info:
Tech Support Guy System Info Utility version 1.0.0.1
OS Version: Microsoft� Windows Vista� Home Premium , 32 bit
Processor: Intel(R) Pentium(R) Dual CPU T2330 @ 1.60GHz, x64 Family 6 Model 15 Stepping 13
Processor Count: 2
RAM: 2037 Mb
Graphics Card: Mobile Intel(R) 965 Express Chipset Family, 448 Mb
Hard Drives: C: Total - 227412 MB, Free - 101980 MB; D: Total - 11060 MB, Free - 4533 MB;
Motherboard: Gateway, , Rev1.91.18, V7CBMYY60722CE706X
Antivirus: None
wMy Gateway notebook won't connect to the internet even when directly connected to the router. When I ran the diagnostic, it said to reset the modem. When I went into Device Manager, there was no modem listed. I did reset the wireless adapter- to no avail
View 1 Replies View RelatedI just reinstalled my windows 7 OS and now my gateway laptop won't connect to the internet. In the network and sharing center there is a x between my computer and internet. I have a westell versalink model 327w and all the other devices in my house can connect except my laptop
View 5 Replies View RelatedATT just sent me a replacement Netgear 7550 ADSL Gateway. I previously had a 2Wire modem that could connect with my Mac desktop and Toshiba laptop without issues.Now my Mac is up and running wireless on the new gateway (no problem), but the laptop (Windows 7) is not connecting and Windows troubleshooting goes not resolve the problem. It will connect via Ethernet but ATT could not get it on wireless. The ATT tech signed on the the laptop and could not get it done.
View 1 Replies View RelatedI have a Gateway NV53 laptop that has no problem connecting to the Internet at home, whether when it's connected with the wire, or wireless (with our own secured wireless network).
However, whenever I go in a coffee shop or anywhere else that has a unsecured network for customers, it won't connect, no matter how strong the signal is.
I cannot connect my Toshiba DX1215-S21 with my 2wire gateway. There are 7 devises that are connected and on wifi.
View 1 Replies View RelatedI was about to portforward to be able to make an minecraft server. but i can't connect to the default gateway 192.168.1.1 so for the moment i use hamachi but i would wannt to portforward it to make it easier for others to join.
View 3 Replies View RelatedI've got two RV082's connected. Each has a dynamic IP (changes typically every few weeks). I've configured the tunnels on both ends with a local and remote "Remote/Local Security Gateway Type" of "Dynamic IP + Domain Name(FQDN) Authentication".If I look at the VPN Summary tunnel status, it shows an IP address of "mydomain.dyndns.org 0.0.0.0" under the "Remote Gateway" column heading. The Tunnel Test "Connect" button is N/A.I can resolve both of the mydomain.dyndns.org entries on both sides of each VPN using the Diagnostic DNS lookup tool within each router. If I hardwire a fixed IP address for the Local and Remote Gateway everything works just fine. VPN is good.
I just can't seem to get the "mydomain.dyndns.org" function to work. It appears the router can't resolve the dynamic IP from the domain names on each of the routers.
I replace our aging rv082 routers with wireless rv220w routers. The gateway to gateway vpn works great, however I am no longer able to manage our print servers port 80 management page. I can ping any host with success, and I can manage hosts that have a port 10000 or 8000 web interface - but no port 80 ones... I had no issues when using the old rv082 routers...
View 0 Replies View RelatedI picked up a pair of RV220W's and before I spent loads of time at a remote site, I figured I'd go through some VPN testing at home to make sure I could get it setup properly. What this means is I've plugged the Internet uplink into a switch, then from the switch into both routers & configured them (using unique static IP's for each) from there. For what its worth: While I have some IT experience, I don't have strong networking experience.
I setup several VLAN's on the local RV220W, and the end result is to make it so that an asset at the remote site with an IP in any of the ranges (192.168.121.0/24, 192.168.131.0/24, 192.168.141.0/24 and any future VLANs) can communicate with/access resouces at the local site. Likewise, an asset at the local site with an IP in any of the ranges (.121, .131, .141 + any future VLANs) should be able to reach the remote resources (currently just 192.168.181.0/24, but future VLANs as well).
This evening I tried to focus on the relevant VPN pages of the Administration Guide to get the VPN up. Leaving the defaults I got as far as establishing a link between both sites and it seems that things are working right: From the remote site (.181) I can access the local site (.121, .131, .141); and from the local site I can at least ping resources (a laptop) on the remote site. (Yay!)
However, when I physically connected an asset that had a 192.168.121.X, 192.168.131.X and 192.168.141.X IP addresses to the remote RV220W (which is 192.168.181.0/24), I couldn't see it from the remote or local sites.I assume this is expected. But I'm reaching out to the community to see what other possibilities might be available becuase networking is a weak area for me. I figured it might be something like a Static [or Dynamic] Route but I really am not 100% sure.
'TECHNICAL' SPECS
Local Router LAN/WAN Settings:
LAN IP: 192.168.121.1 on default VLAN (1)
VLAN 13 defined 192.168.131.1 with DHCP enabled; Reservations created outside of DHCP scope
VLAN 14 defined 192.168.141.1 with DHCP enabled, Reservations created outside of DHCP scope
Inter VLAN Routing enabled for all VLANs
[URL]
config setup
protostack=netkey
klipsdebug=none
[Code]....
I recently swapped out an RV082 with a newer model (still RV082 but black and a different interface). I configured the Gateway to Gateway VPN exactly as it was before but none of the three other RV082's will connect. I have tried deleting the connections several times to no avail. I have aggressive mode disabled and have tried with the firewall on and off. Below are the settings (IP's have been X'd out) and the log.
Settings:
IP OnlyIP Address : X0X.X0X.20.31Local Security Group Type : IPSubnetIP RangeIP Address : Subnet Mask : Remote Group Setup
Remote Security Gateway Type : IP OnlyIP AddressIP by DNS Resolved : Remote Security Group Type : IPSubnetIP RangeIP Address : Subnet Mask : AES-192AES-256AES-128 AES-192AES-256 AES-128 IPSec Setup3DES Keying Mode : ManualIKE with Preshared keyPhase 1 DH Group : Group 1 - 768 bitGroup 2 - 1024 bitGroup 5 - 1536 bitPhase 1 Encryption : DES Phase 1 Authentication : MD5SHA1Phase 1 SA Life Time : secondsPerfect Forward Secrecy : Phase 2 DH Group : Group 1 - 768 bitGroup 2 - 1024 bitGroup 5 - 1536 bitPhase 2 Encryption : NULLDES3DES Phase 2 Authentication : NULLMD5SHA1Phase 2 SA Life Time : secondsPreshared Key : Minimum Preshared Key Complexity : EnableLOG:
[code].....
My two RV042 , one at home and the other one at my working site, constantly lost VPN connection after successfully connected.Both Firmware are identical. [code]
View 1 Replies View Relatedwe do have 2 Rv042, one in my office and one in my house.. in the office we do have static ip and at home none.. question is can i connect the two RV042?
View 1 Replies View RelatedI have some problems in my network with Gateway to Gateway Vpn Connection using two Rv042 routers.
I cannot ping the computers with static ip configuration.
In local an remote computers who have DHCP ip configuration i can ping each other .
Can I have use a Gateway-to-Gateway IPSec tunnel whereby a user can surf the Internet using his local Internet connection and at the same time connect through the IPSec tunnel to a remote subnet using RVS4000 routers?
View 1 Replies View RelatedWe have a VPN setup between two Cisco RV082 routers, the VPN status shows as connected however I can't ping the other network. I am unable to ping between routers, let alone ping computers behind those routers.
We have 2 branches, branch 1 is on a static IP and branch 2 is Dynamic. I am able to connect via QuickVPN from Branch 2 to Branch 1 and remote desktop to computers, however have yet to VPN/remote desktop in the opposite direction.
To me it seems like a firewall issue at branch 2, but what's causing this. Also they are currently running 2 differnet firmware version not sure if this would cause a problem.
i am trying to setup a vpn Gateway To Gateway when i setup the vpn i can ping the 2 rv042 i cant see any computer in the network places when there comect we need to see the computer in the network places so are pos will run?
View 1 Replies View RelatedI have two Cisco RV042 Routers, they are being used to connect two offices, i have created a standard gateway to gateway connection, fixed public ip addresses on both sides and everything works fine, except when the tunnel gets disconnected, it does not connect back automatically, i have to log into either router console and click the connect button to get the tunnel working again, this is really annoying since it happens once or twice a day at least.
View 2 Replies View RelatedI have a pair of RV082 routers and I'd like to configure gateway to gateway VPN tunnel as described in a cookbook, "How to configure a VPN tunnel that routes all traffic to the Remote Gateway," (file name Small_business_router_tunnel_Branch_to_Main.doc). I followed this cookbook and found that my while the Main office has internet connectivity, the branch subnet doesn't have internet connectivity.
Routing does behave as advertised, where all traffic does go to the main office. However, the 192.168.1.0 subnet in the branch office does not get internet connectivity. I've read in other posts that the Main office router will only provide NAT for the local subnet, not the branch office subnet. Is there a way to configure the RV082 router to provide NAT for all subnets?
If not, which Cisco product will provide the VPN Tunnel connectivity as well as the NAT for all subnets? Can the RV082 be used as part of the final solution or are my RV082s a wasted expenditure?
Following is the configuration that I'd implemented, (real IP and IKE keys are bogus).
Gateway To Gateway
Remote Main Office
Add a New Tunnel
Tunnel No. 1 2
Tunnel Name : n1-2122012_n2-1282012 n1-2122012_n2-1282012
Interface : WAN1 WAN1
[code].....
I have two Cisco RV8082 Routers which I would like to setup a VPN Tunnel with Gateway to Gateway. One location is a static IP Address. The other location is a dynamic IP address.
View 2 Replies View RelatedCan not connect computer to Cisco Connect -.Receive error msg 82BD0305. Reset to EA3500 to default and reinstalled software.
View 8 Replies View RelatedOkay, so our old computer took a dump & our friend rebuilt us a new one and he threw in a new router to go with it. Its a D-Link router, which is directly connected to our desktop. However, upon completion of a new desk installment, we put the router into the cabinet and my gateway laptop immediately stopped being able to connect to the internet or the router at all.
1) The router is connected to the internet and broadcasting.
2) I've reset and refreshed the router and my window of available networks on my laptop, which did not work.
3) I've pulled it out of the cabinet, which also had no affect.
4) I did a manual search for the router, and it says the network already exists and asks if i would like to connect and upon agreeing to this, it returns me to the page of available networks, which does not include my router.
My gateway vista m-6750 laptop will not connect with wifi. Why is this. I used the operating disk that came sigh the system and nothing. I aso used the two restore CDs that gateway sent me and still no wifi. It won't connect at the free wifi hotspots. I even have At&t wifi service for $19.99 and still no wifi.
View 6 Replies View Related