Connecting Wireless Modem To Router
Jul 7, 2011
I just had charter install a wireless cable modem into my house and it was put in my study. however, i would now like to get my xbox 360 running as well as the internet for my blue-ray player and tv. So i bought a wireless router.The modem from charter is called: Ubee wireless cable modem (from charter)The wireless router purchases is: Netgear N300 wireless router (wnr2000v3) I am trying to connect them wirelessly. Like I said above, my modem is in the study and the router is about 30 feet away in the living room area.
View 1 Replies
ADVERTISEMENT
Jul 26, 2012
I have a wired ADSL modem+router, and also a Linksys WRT54G2 V1 router. How do I connect them such that I get a working wifi available?
View 1 Replies
View Related
May 23, 2012
Have had ADSL installed through a router, connected the wireless router and it works fine Have since connected the original router via -120mtrs of CAT5 cable to extend to the house. Connection through LAN is fine into desktop however the minute we try to connect an additional wireless router the connection fails. We have even put the LAN from the second Wireless into the desktop and there is no connectivity.We have had a technician come to sort the problem, they advise that they have no explanation as to why the LAN works from the distance but the wireless does not. They have suggested that we need to cut the CAT5 half way and put an antenna up to connect the two routers.
View 1 Replies
View Related
Jun 23, 2012
Trying to connect one computer to the internet using a USB Verizon Pantech modem and at the same time connect to printer wirelessly through a Linksys router. We are able to connect to one or the other and can print when connected to the home network or we can surf when connected to the Pantech. We can connect to both networks at the same time, but when we do we can neither print or surf.. It cannot find the printer and does not access the internet at all. Is it possible to do this without buying additional hardware
View 3 Replies
View Related
Feb 7, 2011
I am trying to connect a Netgear wirless router to my cable modem. I have followed the instructions on the set up wizard but it fails to get a connection with the IP and DNS info I provide.I got the IP address info by connecting intially direct from the modem to the PC and then went to Run CMD and type ipconfig /all. I then started the set up wizard and followed the instructions, turning things on in specific order etc. After input the IP and DNS info it reports an error and tells me to check the address information is correct.My internet is a static IP connection (so it tells me and the IP information doesn't change).
View 3 Replies
View Related
May 17, 2011
When I connect my DSL modem to my DLINK wireless router, two identical DEFAULT connections appear in my wireless connection detection. Both will only connect locally.
View 5 Replies
View Related
Jul 19, 2012
I have a Linksys E2500 and I'm trying to connect it to my ISP provided router (Actiontec V1000H) because I wanted better range and consistent connectivity for my 6+ wireless devices.My problem is that, to make this work, I connected an Ethernet cable from the E2500's yellow internet port to one of my V1000H's LAN ports. This, however, did not give me access to the internet even though the network for my E2500 was available in the network list and selected as the default network. I then had to go the the advanced settings of the E2500, and changed the router IP address from 192.168.1.1 to 192.168.2.2. This granted me internet access.However, everyone i've talked to including coworkers and experts at dslreports said that, because of what I've done I've set up a double NAT with 2 potentially conflicting IP addresses, and down the road weird issues will arise because of it. They also suggested I connect the E2500 to a dedicated modem to avoid this problem. However, the dedicated modem I was sent was faulty and did not allow internet access even through the ethernet connection. So, until I get a new dedicated modem, I have to use the router/modem combo.What should I do? Should I set up the E2500 as just a wireless access point for my existing router/modem combo? What do I need to edit in the advanced settings?
View 6 Replies
View Related
Mar 6, 2012
My parents are using a speedtouch 546 modem for their wired internet connection, but they would like wireles in their home. I therefore bought them a linksys e1200, and tried to get their wireless internet working.
I connected the e1200 to the speedtouch via kabel, used the cisco software to install the wifi network, and so far so good. The laptop has no problem connecting to the e1200, but no internet connection, whatever I do.
There seems to be a signal comming into the back of the e1200, since the led on both the speedtouch and the e1200 are responding, indicating that the two are sharing some information.
Looking for information on the net, I came onto 3 possible solutions.
One is cloning the MAC adress of the to the speedtouch connected wired computer to the e1200. The second has something to do with interfering IP adress ranges. The third was uninstalling the cisco software, reconnecting and resetting the modem. Let windows find the hardware and just install the e1200 drivers.
View 2 Replies
View Related
Feb 20, 2013
I want to create a DMZ by having a less sophisticated router connected to cable modem, which would have the webserver which contains no sensitive information, and then the EA3500 to which my laptops and desktops which contain sensitive information would connect to. Can CCC work through that first router?
View 6 Replies
View Related
Jul 18, 2012
Where I work, we have four computers connected on a network with a Telus combination router and modem (I should probably also mention that two of the computers are connected to a switch which is then connected to the Telus modem/router because that is how the previous tenants set it up) . Recently, my boss wanted to have two different wi-fis, one as a guest wireless and a password one for the employees so he bought a Cisco E2500. I set up the second router as a wireless access point, but eventually we started getting problems with IP conflicts which started messing with the work group connections.
How I'd go about setting up the E2500 properly so that there are no problems like I've been having (having to reset the modem/router constantly for the internet to work, computers being assigned different IP addresses and problems connecting to the server over the workgroup network).
View 1 Replies
View Related
Mar 11, 2012
My home lab is in a different room than the cable modem. I have a wireless N router in the room with the cable modem. I have a wireless access point that is connected to a Cisco 2611XM routers fa0/0 interface. The 2611 accepts the DHCP address from the wireless router. However, I can't ping past the wireless LAN 192.168.10.0 network. I know with the wireless router it's two layers of DHCP. Should remove the DHCP settings from the wireless router? The wireless router is a TrendNet TEW-651BR. I can ping my iphone or any device conntected to the wireless router. And my laptop can ping default gateway of the wireless router, which I assume is the cable modem, however the 2611 cannot. So I'm assuming that's why the hosts behind the 2611 can't get to the internet. I followed the below instructions. I know the instructions don't assume your using a wirelss router between 2611 and the cable modem. But, I really don't want to run a cable to the cable modem.
[URL]
View 5 Replies
View Related
Aug 11, 2011
Two days ago we received our new phone land line from Mediacom. We already had internet service from them so we decided to get a phone line. When they came over two days ago, we received a new modem, RCA DHG535-2. The issue we are experiencing is that the modem is not connecting to our rt n-16 ASUS wireless router. The modem works fine without the router but we need it for school work. The troubleshooter says "DNS is not available".A few things i tried was to unplug everything and reconnect them back from the modem to the computer.It usually works when i had trouble in the past but it seems nothing is working.
View 4 Replies
View Related
Aug 23, 2011
I HAVE AN I BALL BATON iB lr6111a and i need to connect the same to a router but it has only one rj45 port since the router dont have a modem how can i connect it to a modem with only one port.
View 1 Replies
View Related
Jun 13, 2011
My aunt's connection was working fine until the other night. Apparently a storm we had knocked out their power and the next day they could not get on the internet. They were on the phone with tech support from their service provider and "had them reset the modem." This is basically all I could get as they are not very tech oriented.
From what I gathered: The modem and the router are not communicating with each other. The modem is a Motorola ADSL single port Ethernet modem, and the router is a Netgear Rangemax wireless router WPN824 v3 with the modem connected via the uplink port on the router. Whenever the ethernet cable to the PC is plugged directly into the modem, there is a connection. I exhausted my entire networking knowledge trying to figure out what could be causing this.
View 3 Replies
View Related
Apr 26, 2012
How to connect 2 cisco modem in 1 3com router.
View 6 Replies
View Related
Nov 22, 2012
I have a problem connecting wifi router(airlive wt-2000r) to my ADSL modem(webstar epc2203ed2.0) using utp patch cable. When my PC is connected straight to the ADSL modem everything works like charm. But when I connect modem with wan port on the router and router with my PC I get no internet access. The network shows as unidentified network and win7 troubleshooter says: Default gateway not available. Connecting them two devices seems pretty simple and I dont think I am doing anything wrong so what could be the problem?
View 1 Replies
View Related
Nov 6, 2012
I am trying to connect my modem with router (ASUS WL-500gP V2) but don't have any luck. Internet is not working with router.
View 9 Replies
View Related
Feb 5, 2013
I'm sure that the modem/router is bridged which I think it means that it is sent to pass through the port number requests. What I did was go into my Linksys router, setup the port I want to forward to my 3389 (RDP port on the specific machine). Let's say port 45000. In the past, before Windstream took over and I had DSL with a local Telco, I would just enter my IP address and port number and I was in to the machine. Example: 171.234.54.191:45000 That would be the IP address of my modem (which just passed though the requests) to the router. Now when I do the same thing I just get an error message that looks like this: It seems that the modem/router is not passing though the request to the router. This is why I didn't want their new router/modem which the HAVE to charge $120 for worse quality machine than what I already had.
View 2 Replies
View Related
May 18, 2012
I recently borrowed a friend's desktop and I am having issues with connecting with the router through an ethernet cable. I go to troubleshoot the problem and I get "Local Area Connection 2 doesn't have a valid IP configuration". Its nothing with the router because when I plug my laptop in with the same ethernet cable, I am able to connect perfectly.
View 19 Replies
View Related
Jan 12, 2013
I am trying to connect my DIR 815 router to a DSL modem.
I fill out the password, and the username the way it should be, but then when I try to get the modem to connect, it says the network status is busy.
View 1 Replies
View Related
Dec 24, 2011
how can i connect a Net gear DGN2200 wireless modem router to a D link DGL4500 wireless router ??
View 1 Replies
View Related
Dec 9, 2012
i have one airtel isp connection was connected to beetel adsl modem and this modem is connected to d-link switch to accessing internet for my lan. and one netgear wireless router is aslo connected to this d-link switch. my need is i has one cisco 1900 router, i want to get internet access from adsl modem or netgear router to my cisco router.
View 1 Replies
View Related
Jul 21, 2011
I have a wireless modem. Its main connections are power, and phone line. Since its a wireless modem it is not connected to my PC through wire. i have a Data card USB which is plugged in my PC. The wireless modem senses this Data card and my internet was working normally. I live in New-Zealand and I was having a Telstra Clear connection with their modem and Data card. Since it was acquired by Telecom, the internet provider had given me this new wireless modem but the Data card remains the same.Now this new wireless modem is not connecting. But the laptops are getting connected through WiFi. Since my PC has no WiFi, it uses this data card. My PC is not getting connected to the internet. I tried plugging in the USB Data card in and out, updating the drivers and stuff.I want my PC to get connected to the internet.
View 3 Replies
View Related
Oct 29, 2012
I just got a DSL Modem router (DSL 2750U) which has DSL input for internetconnectivity.My internet service provider provides RJ45 Cable which needs LAN input socket on a router for internet connectivity. How do I connect?
View 4 Replies
View Related
Jan 10, 2013
I have two wireless modem/routers - a Ugo Mach5 CN458 and a Swift 4G - in two branches of my company that are distance apart and i want to connect them together so that they can be on the same network and workers in both branches can communicate and share files.
View 2 Replies
View Related
Mar 19, 2011
I am trying to connect an xbox 360 to my wireless modem.
View 2 Replies
View Related
Apr 22, 2012
I have a 192.168.1.xxx network connected to Verizon FIOS via Actiontec MOCA / router. I also have a 192.168.15.xxx network connected to Comcast via Motorola VT2442 router (used for Vonage) and a Motorola SB6121 cable modem.
Each network has it's own gigabit switch connected to each router. The two networks are physically separated but switches and routers are physically side by side.
What is the best configuration to allow devices on 192.168.1.xxx network to communicate with devices on the 192.168.15.xxx network (share printers, NAS, etc), but still have each network served by it's respective ISP, and each device still get it's dhcp, dns, gateway, etc from each respective router?
View 6 Replies
View Related
Mar 29, 2010
I am having an issue with connecting to a Cisco 7201 via the AUX port through a modem. The modem is plugged into the AUX port and I am dialing into the modem, everything seems to be working fine as I get a login prompt and my banner etc but I can't type anytihng. If I type then nothings happens... If I just type a bunch of random characters on the keyboard then when the authentication prompt times out and it goes back to the username, it will show a few of those characters.. I have tried many things, changing speeds etc, I have even tried changing modems and it is doing the exact same thing.Here is my config:
line aux 0 exec-timeout 2 0 modem Dialin transport input all stopbits 1 speed 115200 flowcontrol hardware
I have searched on here and found people having similar problems but no solutions. I have tried this one a Cisco 2821 with the same config and it works with no problem, the only difference is the phone line is different.
View 7 Replies
View Related
Oct 21, 2011
I recently purchased a new Belkin N wireless router, model number (F5D8236-4 V3), i am however trying to connect this router to my old Belkin G wireless Modem Router (F5D7632-4 Ver7000uk).Now i can't seem to get the N router to connect to the internet-after much faffing about i can get all the LED lights to turn blue-bar the wireless which blinks amber (i did this by turning the DHCP server off, and by using the same WEP code). I get limited connectivity wirelessly and wired, which basically might aswell just say no connection.
Taking the N router out of the equation, the g router can connect to the internet wired (it no longer seems to work wirelessly, and had a horrible range on it anyway). I use a PPPoE connection-all my ISP details are correct.how i can get the N Router to work wirelessly and wired.
View 6 Replies
View Related
Apr 23, 2012
I have recently purchased a new HUAWEI wireless modem. This lovely little device will connect beautifully to my iPad, to all the Acer computers at work, to my Samsung mobile phone. It will not however successfuly connect wirlessly to my Dell Inspiron N5010.
I plug it in via a USB port and can connect to the internet that way. If I unplug the USB cable the computer says I am connected but when I try to access a webpage the browser says I am not connected. In the bottom right of my screen my computer says I am connected. This is most confusing and frustrating. I took the computer to work and had the IT department look at it but they had no answers for me.this same computer has recently been connecting to a different wireless modem so I am at a loss.
View 6 Replies
View Related
May 13, 2013
Management has decided to put in a Wireless network and want to keep it sepeate from rest of the network. I have been asked to scope out DSL/Cable internet connections.
I am not familiar with setting up 2504 with dsl router.
Any basic guides for setting up 2504 with a dsl? do i need any static ip addresses for this setup or dhcp lease provided to cable modem would do?
View 3 Replies
View Related
Dec 8, 2012
I have linksys router connected to my cable modem. I want to change it Belkin AC900. How can I keep the linksys connected until I have tested set up for Belkin AC900 router.
View 2 Replies
View Related
Sep 14, 2012
I have a new inspiron 15 laptop and also bought an all in one wireless printer. I have a iinet BOB lite modem. I cannot for the life of me figure out how to get the wireless printer, modem and laptop to tall to one another. Am I missing something or should it all work? The laptop has internet access. The laptop also shows the printer installed with a big green tick next to it but it says it is offline. At no point has a green light appeared on the printer to indicate any wireless connectivity to the modem.
View 2 Replies
View Related
