They time out however I can connect to google/ect on my browser.
Microsoft Windows [Version 6.1.7601]
Copyright (c) 2009 Microsoft Corporation. All rights reserved.
C:UsersHannah>ping www.riftgame.com
Pinging www.gslb.riftgame.com [208.94.26.135] with 32 bytes of data:
Request timed out.
Request timed out.
[code].....
I'm working as a network engineer for a service provider, and we had just gone through a pretty large scale upgrade throughout our network and service.But not long after the upgrade (or maybe ever since the upgrade, we can't confirm this because we probably missed it out due to many other links to be tested), we met a peculiar problem.Everything seems to be running fine most of the time, but there has been some weird 'ghost-like' activity which have been causing inconsistent network disruptions. At times, certain portions of the network can't communicate with other subnets.And most obviously is the problem with a continuous ping and a traceroute simultaneously. Ping is usually normal, but until a traceroute is attempted, it times out at the same time as tracert fails to obtain the route.Besides, performing a ping from the 2nd closest hop address, 10.250.253.251, which is a cisco layer 3 switch also has problems, the results shown are as belowType escape sequence to abort[CODE]
View 1 Replies View RelatedI can't tracert or ping certain websites or servers for games.Before I go on, no I wasn't doing this because of DDoS-ing. I was doing this so that I could find an exact latency number for a gaming server. Now, to continue.What I mean is if I try to ping this server, the session will timeout no matter what the millisecond limit is (using CMD)
Ping: Pinging (IP Host Name) [IP] with 32 bytes of data
Request Timed Out
Request Timed Out
Request Timed Out
Request Timed Out
[code].....
Why does this happen? I am pretty sure this is a security tactic used to stop DDoS-ing, but why does it not matter how long I allow the tracert or ping to run? I really want to understand this so I can understand how people don't get traced as well as don't get DDoS-ed. I didn't put any of the IP's just to keep it anonymous. If you really need the host IP, I will supply it, but I will not supply the tracert IP's.
How can i enable this machine to be accessible throught PingTracert
View 1 Replies View RelatedI am currently using Time Warner Cable as my internet provider and I have been experiencing very slow internet connection speeds for the past few weeks. This has happened across multiple laptops and desktops both wireless and wired connections. I have done a ping and tracert test but am unable to read the results.
View 7 Replies View RelatedMy friend is invisible to ping requests. I know he is online because he is on my Gtalk friend's list. This is because he is using Windows 7. Earlier, when he was on Win XP, he responded to ping requests. He said that he didn't mess with the firewall settings. Therefore this feature comes default with 7.I'm using XP and I don't want to change to 7 right now. Can I get this feature?
View 5 Replies View RelatedIs it possible to connect to the internet through the Wifi and 3G internet from an iphone at the same time.If its possible are there benefits from it?
View 7 Replies View RelatedI have a Philco PHN 15006. My drivers should be up to date. Since I've started using it, I noticed I lose connection with internet and then I have to restart the switch/router. Then, it starts working again. I used to have to just open the Solve Problems and then it would connect again. But now, I tried just unplugging the Ethernet Cable and plugging it again. It had the same effect as restarting the switch. So, the problem must be in the notebook.The wireless internet is worse, because it connects for a while then stops connecting, while my other computer connects with no problems.
View 12 Replies View RelatedI have two routers one is a o2 router which is for the internet (broadband) the other is an old bt home hub which i have connected to the printer via usb. In order to print a document at the moment i have to disconnect my laptop from the broadband router and connect it to the printer router.Is there any way that i can connect to the two router s at the same time so that i while printing i can still keep my internet connection.
View 1 Replies View RelatedWe recently upgraded to Windows 7 at work and my laptop was part of the first deployment. Laptops are imaged so that all configurations/software are already set and done. My problem is as follows, my laptop is part of domain, when I am at work I can ping anything just fine (network computers, printers) BUT when I am at home, I can't even ping my own PC. It returns back with the same address over and over. No matter what I ping when I am at home, it returns back with the same address. I can ping blah and it will display same address over and over. The weird part is I can ping websites no problem, but if i ping random names it will format as follow.Lets say I want to ping lost, below is what i get (I made changes to hide domain and IP)
Pinging lost.domain.com [70.99.199.99] with 32 bytes of data:
Reply from 70.99.199.99: bytes=32 time=57ms TTL=50
Reply from 70.99.199.99: bytes=32 time=58ms TTL=50
Reply from 70.99.199.99: bytes=32 time=57ms TTL=50
Reply from 70.99.199.99: bytes=32 time=58ms TTL=50
[code].....
Notice how my domain always shows up? When I am connected to the VPN at home, I have to log onto our intranet using the IP, I can't use the name, it wont direct to it.
I am using a linksys wrt600N with easylink advisor version 1.6.0042. I am trying to install a video camera and the instruction manual says under "known issues": LinkSys routers have a factory default setting in the firewall menu called "filter anonymous internet requests". If you want to access your camera from the internet you have to uncheck this option."I see this option in the WRT600N manual, but it references a software choice that I don't have.I have gone to the website and downloaded the latest compatible software version, and I still don't have the choice to uncheck this option.
View 2 Replies View RelatedI have a cisco 2021 router and I configured firewall and Site to site VPN on it, but recently Ism experincing and issue with, I have dropping in the connection and this issue, this make the VPN connection to have a slow performance and some time disconnection.
View 3 Replies View RelatedI’m looking for some notes from the field guidance here from those that have much more deployment experience.
I have a GSS and an ACE, and its the ACE that's primarily giving me something to think about, in terms of placement and what mode to adopt.
The traffic flow will look loosely like this:-
Client---Internet---Firewall---GSS---ACE---Servers
Physically, it's like this. The RED line denotes a boundary, and pretty much anything North of that is not accessible to us, we simply have a L3 trunk between our switches and "their" switches (S3/S4) and talk using EIGRP.
There are other servers in the top tier, some that also require load balancing, some that don’t. Typically, I want to load balance HTTPS requests from the internet, to one of the 3 servers in the top half.
I’m not sure what mode to select, routed, one arm? What about placement of the ACE? At the moment, I’ve just configured 1/1 on it and made it part of the MG MT VLAN, it's S VI exists on the S1/S2 switches, so I’m open to change as it's still all in the lab.
when do we get Desteination host Unreachable and time to live exceeded while trying to ping .
From 10.1.1.1 icmp_seq=2 Destination Host Unreachable
From 10.1.1.1 icmp_seq=4 Destination Host Unreachable
From 10.1.1.1 icmp_seq=7 Destination Host Unreachable
I have a brand-new WRT160N router (just installed FW v3.0.02) that I am using in mixed mode, 20MHz only, Channel 11, not filtering anonymous requests, beacon at 2306, RTS at 2307, fragmentation at 2346, MTU at 1400.
These settings bring the response from a simple ping command over the wireless network down to approximately 6ms on average, which is good. However, when I still noticed inconsistency with my internet response over wireless, I decided to do a test.
By simply running the "ping" command on 192.168.1.1 (the router address) over the wireless network repeatedly (approx 3 seconds between commands), I can see that approximately every 65 seconds or so, router response time increases to over 100ms for a few seconds, then decreases down to 6 ms or so for another 65-70 seconds. See the chart below. The interval looks pretty consistent to me, with the exception of one stretch where it goes for over two minutes without a spike. I see this pattern regardless of what else I'm doing over the network. I do not see this behavior running the same test when physically wired to the router (ping response time is a flat line at 0ms).
I have a specific website that i cannot reach. I can reach all other websites without any problems.I have read this URL and followed the same instructions.I made the tracert and here is what i got.
View 5 Replies View RelatedEach time I'm rebooting my E3200 device my ping to my ISP is 20ms. Few hours later the ping goes up to 300-500ms.Than I reboot again and the ping is going down to 20ms again.
View 5 Replies View RelatedI have newly deployed network. I have two ASA5520-AIP20-k9. both connected to ISP and configured as Active/standby failover. the ASAs were working fine at first but later on, the internet connection becomes very slow. the ping reply i am getting from my next hop(ISP router) varies during the peak hour is some times in 2000 msec or above but during off hours, the ping reply time is 1 and 2 msec. when I directly connect my laptop to the link that comes from the ISP its ping reply is 1msec and 2msec. I thought the ping reply of the ASA5520 to the ISP gateway should be constant and should be 1 and 2 msec regardsless of the traffic passing through the firewall.
View 1 Replies View RelatedMy customer has various Cisco switches but only cisco 2950 switches has the problem of ping timeout or reply time is too long(average more than 2 sec). It will cause I Network Mangement software alarm always.
View 4 Replies View RelatedI have a fresh out the box asa5510 with 8.4 on it.I have built these before but for some reason cannot get this one to work. I am consoled on, have applied the following config but can still not ping to or from, can not asdm, cannot http/s. Arp table shows device it tries to ping, but device trying to pping it has incomplete arp entry. [code]
View 7 Replies View RelatedI have a ASA 5505 as a default gateway to a network, whenever I tracert to outside it shows every hop ip address as the ip address I'm trying to get too, quick example
lets say I'm in a 192.168.0.0/25 network but I want to trace to 10.10.10.10
From My Router that connects to Cable modem i am unable to ping website 4.2.2.2I am able to ping all other websites fines.Same website i can ping from my pc and all other switches fine.Router has only 1 ACL thats for NAT.
View 25 Replies View RelatedI want to create an ad hoc network on my lap and when other users connect to my ad hoc network and open your browser for the first time ... I take a personal website, not to have set in your browser ..
View 1 Replies View RelatedI have a Windows7 laptop that was working fine til yesterday.I switched it on at home last night and it picked up my wireless connection but when I opened IE or Firefox it would not access any webpage (blank screen, no address that its resolving on status bar at the bottom and just a progress bar (IE) or a 'searching' icon (firefox)The network connection page in control panel says that it is connected and I can ping sites from the command prompt and some other software such as skype seems to be connecting.I have disable both bullguard firewall and made sure the windows firewall is off.I have come into work this morning and am getting the same problems, even when connected by ethernet cable, I can also see other computers on the network.I was occasionally getting a dial up connection pop up box appearing from an old dial-up connection I had set up, but have now deleted this connection.
View 2 Replies View RelatedI have a Windows7 laptop that was working fine til yesterday. I switched it on at home last night and it picked up my wireless connection but when I opened IE or Firefox it would not access any webpage (blank screen, no address that its resolving on status bar at the bottom and just a progress bar (IE) or a 'searching' icon (firefox) The network connection page in control panel says that it is connected and I can ping sites from the command prompt and some other software such as skype seems to be connecting. I have disable both bullguard firewall and made sure the windows firewall is off.
I have come into work this morning and am getting the same problems, even when connected by ethernet cable, I can also see other computers on the network.
I was occasionally getting a dial up connection pop up box appearing from an old dial-up connection I had set up, but have now deleted this connection.
How much time is 5gb of internet?
View 7 Replies View RelatedI have WRT54G2 router. All settings are more-less default and the behavior is following.You start up the router. If you do not connect wireless device within 10 minutes, then you have to restart the router.You have assigned IP via wifi, and when you connect cable device to the router, the wifi PCs are disconnected.
View 3 Replies View RelatedI recently purchased a X2000 ADSL modem/router combination. For some reason the current time will not stay set to the time zone. Rebooting clears the discrepancy for a short time before it drops an hour exactly. I'm in the central time zone and the setting are correct on the basic setup.?
View 1 Replies View RelatedIs the WAG320N iPv6 compatable ? ,or could it be with a firmware update ?.Is the X2000 in the same boat in iPv6 terms as th WAG320N ?.Is there a way of retrieving "UPTIME" / "DSL connection time" information from the WAG320N and also line attenuation stats etc.Wouldn't need the above but poor isp needs keeping an eye on.
View 3 Replies View RelatedI have one 2621 router i want to creat time base access list so that one of my subnet user(10.128.194.0 255.255.255.128) use only internet between 11am to 2pm.
View 15 Replies View RelatedI just bought a WAP321 Wireless AP. I wonder why it cannot sync with our time server automatically. Every time I reboot it, the system time become "Fri Dec 31 1999 12:00:00 UCT". I have to do the sync manually by clicking on the "Save" button under the menu Administration > Time Setting.
View 5 Replies View RelatedI'd like to use 2 internet connections at the same time.Assuming there are two internet networks.Network A and Network B (both are either wireless OR one is wireless and one is wired OR both are wireless). So, now I want to use BOTH internet connections simultaneously. However, both connections will still be separate and not combined:If I had to transfer big files, then I could do this on network A.Now, I want to use network B for other "normal" internet use so that the transfer of files in network A gets the maximum speed since there is no interference with anything else.I have to let the computer know somehow that there are two connections used simultaneously. I also have to setup what programs use what connection. E.g., IE uses network a and Firefox uses network b, program "x" also uses network b, etc.I would use two network card/USB Wifi Adapers so that each network card/wifi adapter can connect to one network.how do you realize that without setting a Virtual Machine up?
View 9 Replies View Relatedi want to use internet at home. i want to use my laptop in my room . If i use my lan cable in my room how can i use it. i mean may i use internet on both computers ?
View 1 Replies View Related