It seems that motion monitoring setup for 930L is not working correctly.I've setup the camera to ONLY monitor the half of the screen, but it is still monitoring the other half of the screen as well.I've setup the camera to FTP the messages when motion is detected, and it is uploading the images when the other half contains the motion.
View 6 Replies I've just successfully set up my network camera and as I was running through the advanced settings, what it wants from me when it comes to setting up images being sent to my e-mail. I've looked up some old threads to get a clue and thus far nothing works. Testing my entries results in "Invalid e-mail setting" 10 out of 10 times.
The setting format I'm trying to use is as follows:
-- smtp.gmail.com
-- 587
-- myemail@gmail.com
-- myemail@gmail.com
-- myemail
-- mypassword
-- STARTTLS
My GMail account is POP Enabled (whatever that is) and I used the username for that e-mail for bother the Sender and Receiver fields, as well as that e-mails username and password.
I'm lost. I bought the camera so I could document my landlord's maintenance people "touring" my apartment while I'm at work, but I wasn't aware having it save screenshots would be so complicated.
First of all, I've purchased a couple of Wifi cameras in the past, and they've always been missing something important (i.e. just returned a Cisco camera because it didn't support WPA2-AES).
So I was thrilled when I first received the DCS-930L - it was sleek, wireless setup was easy, and mydlink.com is slick as well.
But I'm afraid I've found the fatal flaw. I purchased this camera for one reason only - to figure out how mice are getting into my basement! I set up the camera where I suspect they're coming in, set up motion detection (via ftp), and then walked in front of the camera to test it.
To my surprise, I checked the FTP folder and found dozens of STILL images! What I really need is a video file. Is there NO way to configure the camera to capture video (not still images) when motion is detected? This seems like a huge gap. The Cisco camera I returned could do this.
If it can't do this, can it can be configured to record the last X hours to a shared drive somewhere, so I can at least go back and look at recorded video?
1. To monitor motion in a block you hash it.
2. To monitor motion in a block you leave it clear.
I am using my new DCS-930L to monitor motion at a door entrance. It is firing off when motion happens but the image it emails is taken @ 12 seconds after the motion. So the result is I know motion happened but the person who came to the door is long gone or through the door by the time the image snapshot is taken. I get multiple emails containing images of the empty entrance. Is this a software, hardware, firmware or user error issue?
View 7 Replies View RelatedI realize that this is a new product, but nevertheless I have some feedback after running my 4 new DCS-930L camera over the past few days.
Currently, you can configure the camera to EMAIL/FTP images on a schedule or when motion is detected, but not both.
Why does it matter? Because I get flooded with email alerts after I get home from work and later in the evening every time I walk by one of the cameras or whenever a light switch is turned on/off.
If I could configured the motion detection to only alert during a specified schedule of days and hours, it would be great!
I recently set up two cameras. I had set up one for motion detection and email to a gmail account. It seemed to work fine, but then for some reason the motion detection tab didn't show the room like it did before. It doesn't show any picture or anything like it did before, so I couldn't choose the squares to choose the detection area. This is through mydlink account->camera info->advanced settings, and logging in to the camera remotely.So I switched to the other camera, and got it working as of last week. But now, the motion detection doesn't work anymore? It appears to be related to the username/password for the email account. I can no longer send test emails, it says invalid username/password, though the exact same values worked last week, and I didn't change anything. I tried resetting it, then setting it again, but no luck.
View 5 Replies View RelatedI'm using a Verizon DSL router, Mac D-Link Camera Setup Utility (BETA), and Mac OS X 10.6.7. Configuration of camera is as recommended in manual with CAT-5 cable. Green light blinks irregularly in a communicating-with-router manner. The setup utility won't recognize the camera
View 1 Replies View RelatedContribute to our DCS IP Camera Third-Party Video Monitoring Software List.Do you have experience using third party software to monitor feeds from your DCS camera? Share your knowledge. post your contributions here: DCS Compatible Software(i.e. sticky at the top of the DCS Software board)
View 1 Replies View RelatedI had to get a new router from verizon cause the old one died. so i reset the camera and wipe all the dlink software and settings. I then start fresh. i get all the way to choosing wireless and input the password. It states that there is a problem saving your settings. I tells me nothing more. I spent 4 hours on the phone with tech support and i can get it working through wired but I can't put it in my childs room wired. it worked perfectly before the router switch. funny thing is that its the same brand and model router.
View 4 Replies View RelatedI have a DLink DIR-615 rev. B2 firmware 2.25. A few days ago, I started using Comodo Unite for VPN access with friends and LAN gaming. However, just recently the program stopped working correctly. I have reset my configuration, tried multiple different settings, and nothing at all has remotely worked.
View 3 Replies View RelatedI'd had my camera offline for the last couple of months, and in the interim I've upgraded both my main pc and the wireless router. I'm running Windows 7 Ultimate 64-bit on the pc, and the router is a netgear gigabit dual band wired/wireless. When running through the camera setup I am not able to get setup to find the camera, whether wired or wireless. I know that the camera's online as it shows in the routers device table, and I'm able to access the camera with my browser. However, the failed setup prevents my registering the camera on MyDlink. Any thoughts? Should I be looking at the ports on the router in regard to the camera's IP?My goal is to be able to remotely monitor my home, which the MyDlink service seemed to offer. Based on what I've read, it appears there are other ways to achieve my goal, but I would like to figure out the install problem.
View 1 Replies View RelatedI have the DCS-930L camera. I need to know how to setup port forwarding/triggering on my router, which is a Cisco DDR2200 CL. I understand that in order to use the camera, i need to do this. how to set up NAT.
View 1 Replies View RelatedI have had a setup in which my four DCS-930Ls transfer picture every 15 minutes over a Dovado-router connected to a mobile broadband modem. This has worked perfectly until this last night. No pictures are transferred and upon using the test FTP function the status page just says "Testing ...." forever. I've also tested e-mailing picture without success.
View 2 Replies View Related"How do i setup a proxy correctly using firefox?"I forgot what addon it was that i was trying to use, proxy fox i assume. If there any better firefox proxy addon that i can use i will be happy to use.I want to know the steps to make the proxy work correctly, because i like to be anonymous as possible when using the internet. I don't care about internet speed.
View 3 Replies View RelatedWe have two laptop computers and our Tivo hooked up to use the wireless internet through our cable company with a Belkin router. Over Christmas we got a camera that emails directly from it, and it told us to press the WSP button on the Belkin router. The camera magically worked, however our computers did not work anymore! After an hour long phone call to Belkin, I got one of my computers to work normally again. However the 2nd laptop won't connect to the internet and our tivo isn't picking it up either, which mean our shows are not recording.
Also, I'm using two apple computers. When I attempt to hook up the airport network, it says "unable to join the network."
I have been having no luck with DLink support getting an answer. I have the DCS-942L which allows me to set the date/time zone but when I try to add motion detection settings the page always times out during the save. I tried using CaT-5 CABLE instead of wifi for settings (camera on same router and desktop pc) but after the "saving" message appears, it eventually times out and I have to click the Back arrow to return only to find none of my settings saved. I also want to note that each time I log in I see a broken certificate error message. Using Win8 with IE10. Also tried on Win7 with IE9 and XP Pro with IE8.
View 3 Replies View RelatedI need to setup an ASA 5520 to correctly NAT over two wan links. The idea sounds pretty straingforward but it does not, I have only 2 IPs that are involved with the NAT
192.168.1.10(Nated Server) -- 172.16.1.10(Web Server)
I have 2 interfaces that sould be applied to it let's say outside1, outside2. The server is reacheable through each outside interface, the outside interfaces is selected uppon dynamic routing and that is working OK.
So if link outside1 is up the Nat follows this schema 192.168.1.10(inside) -- 172.16.1.10(outside1)
that works fine, but I want that automagically changes over when the link outside1 is down to 192.168.1.10(inside) -- 172.16.1.10(outside2).I know I can't have a NAT with 2 IPs and 2 different interfaces (ASDM doesn't allow me to), is there a way to implement this??
I have a 932L already and wanted to add another camera, so I purchased the 942L in the US. I live in Canada. The 932 works perfectly, emailing me without any problem. Set up was a breeze. This new camera appears to be a problem. I cannot get this turkey to email. I am very computer literate, and I have been working on this thing for ages now without success. I would like to return this thing and get another 932, but hard to do from here. I see from these forums that nobody else appears to have gotten it to work either. By the way, I upgraded it to the latest version firmware, no change. How to email images using the motion detection?
View 2 Replies View RelatedWhen activating the option to send mail when motion is detected I am receiving mails permanently while I am at home and walking through the zone observed by the camera.
View 3 Replies View RelatedI have been testing my new DCS-942L and found that while the motion detection works great it is sometime hindered by the audio mic setting of motion detection. I have turned down the microphone settings to the lowest (10) and the only difference is miniscule. The camera will still set off the motion detection prior to anyone being in the screen, and if the person enters the screen immediately after the noise the camera will not record the movement.
I have adjusted the sensitivity down to 25% and continued having the issue. I would like to record motion with sound. So either the microphone needs to be able to be adjusted lower, or not set off the motion detector.
I have a DCS-932L camera setup in my living room with motion detection activated in DView. During the day it works great, but after nightfall the camera shows random lines in the [poor] video. These lines are being picked up as motion and as such the camera records all night long taking up massive amounts of disk space. Even when I put the camera motion detection on 'lowest' value, it still picks it up.
View 10 Replies View Relatedi still play with the motion detection feature of the 942L. Is there a way to see where on the live-picture the motion is detected?I do not see any motion on the srceen but the cam still detects motion and records every 60 seconds. Also i played with the sensitivity but without success. So i had the idea to ask the cam where on the screen the motion was detected...
View 1 Replies View RelatedI use the Windows7 Virutal WIFI when traveling abroad to give my Iphone an internet connection in my hotel.I've had zero issues until this week. The WIFI connection is still showing up on my iphone, but I no longer get internet access (I only get an IP and subnet on the iphone now, no router or DNS info). The issue began (coincidence or not) as my MagicJack downloaded and installed a software update. MagicJack support says they aren't the issue. I experimented with created an Ad-Hoc network...no change. I've removed and reinstalled the wireless card and driver. No change. I suspect some corruption with ICS, but haven't found any solutions online to fix it.
Microsoft Windows [Version 6.1.7601]
Copyright (c) 2009 Microsoft Corporation. All rights reserved.
C:ipconfig /all
Windows IP Configuration
Host Name . . . . . . . . . . . . : Richard-PC
Primary Dns Suffix . . . . . . . : MARCOGROUP.local
[code]....
I recently aquired a 2nd AP1140, however when i configure it for WPA 2 it works inconsistent, a ping for example will work only for 33% of the time.The same client has no issues with my 1st AP using WPA2, with the 2nd AP WEP works without a glitch.
View 2 Replies View Relatedwe are running CiscoPrime LMS 4.1 and I have the following problem.I have configured SNMP Settings as shown below (the order of the targets is exactly as it is configured on the server):As can be seen we use three different read community strings. I also have exluded a bunch of IP ranges and IPs from the filter settings. When I manually start discovery everything works fine, meaning that all devices in the above ranges that need to be discovered are discovered as "reachable". The problem appears in the scheduled discovery (happens once daily). In that case only the devices with Read Community snmp1, get discovered as "reachable". All other devices with Read community snmp2 & snmp3, as well as those that are excluded in the filter settings, are discovered as "unreachable".The discovery uses DCR as seed and seed devices are also configured.I also have a problem with PingSweep in the discovery, but I will open another discussion so that I don't complicate this one too much.
View 1 Replies View RelatedI have 3 cameras. all had the problem that after a while motion detection would be triggered continuously for no reason at all. With 2 of them I managed to fix it with a firware update, but no luck with the 3rd one. I even tried several different firmware versions.) it starts to record continuously after abt 24-48 hrs & i have to reboot to get it to stop.
View 1 Replies View RelatedMy RV220w has a problem with DNS. I have configured the device for my network, but it seems as though DNS is not working correctly. For a background, I have a primarily Windows environment in my network, W7 PCs. I use homegroup to share files/printers amongst them. I like that I can type "\<server-name> in the Windows search box, and up comes the other computer's files. This functionality is still there with the RV220w, so that's not my issue. My problem arises when attempting to type "<server-name>" into the Remote Desktop Connection dialog box. I can no longer RDP to my other computers by name. Attempting by IP does get me there.
View 11 Replies View RelatedWe have LMS 4.1 - it was working perfectly for some time - it was rebooted and now the services don't start correctly. I manually started most of the services but the Daemon service will not start.
The main page comes up and after I log in - all the sections list an error
'License Server / Deamon Manager is down. Please check license.log for more information'.
The idea is to get the date/time logged motion detection is triggered on a certain time frame of the day (5:00 am to 5:30 am), to a txt file or something like that. I plan to port the log to a html/php website.
View 1 Replies View RelatedOn my new 942l, after 5 days of usage and tinkering with various settings, I cannot get the camera to obey the trigger=motion when configured to send snapshots over email. It does work when configured to send snapshots over email with trigger=always.Interesting enough the trigger=motion works just fine to upload snapshots to FTP. Yes, it uploads the pictures correcty on FTP detecting correctly movements, but it would not send those over email. To me it looks like a bug in the firmware that I have now a 100% repro.Are there any logs you want me to send to you for debugging?And : Is there a known workaround I can apply (reboot, resetup etc)?
Detailed description of the problem:I have setup the camera to upload snapshots to FTP AND send them over email for trigger=motion.This is what works : the snapshots are nicely uploaded on FTP , but not sent over email.Interesting : if I set trigger=always, snapshots will both be uploaded to FTP and sent over email. The moment I switch back to trigger=motion they go only to FTP and not over email.Even more interesting : the video clips work correctly with either email or FTP for trigger=motion.
What could cause this?The email (account, port, password) and FTP settings are definitely not a problem since I see pictures/videos in email or FTP with trigger=always.The motion settings are not a problem either since snapshots upload correctly on FTP when movements are detected.What it apears to be is the software is not reading or obeying correctly a certain combination of settings.I'm wondering if it has to do with the fact that for video clips the "email" and "ftp" are exclusive, but for snapshots they are allowed simultaneously. And somehow the logics get mixed up causing certain combinations of settings to now act out?
What else I tried?I tried many reboots, unplug followed by plug back in and so on.I tried saving and restoring the settings to/from a file hoping that will "reset" something.And I tried many combinations of settings, including changing the order I set and unset hoping a different code path that works will be hit.I did not try a restore to factory defaults since I installed the camera in a hard to reach place and if I restore to factory defaults i need to take it down connect it to a cable in order to redo the wifi settings.
I'm puzzled that you don't seem to be able to do this (a basic feature). Seems like when motion is detected you can only send an email or do the DI/DO thing.
I can do this quite well via the direct web-based interface (1.03 and earlier at least) on the DCS-1130, but the 932L doesn't have video record on motion option (baffled as to why not there too, but that's another issue). So, I was thinking of using the DCS software to get motion-detected recording out of the 932L, but looks like I can't do that either?
The internet connection on my laptop does not work correctly when connected to lan ,but it works fine for the WIFI.i checked the internet connection ,it works fine in other computes.most of the time the connection through lan is not recognized. sometimes it works fine for 1 day and does not work for another day.
View 8 Replies View Related