I have a DLink DIR-615 rev. B2 firmware 2.25. A few days ago, I started using Comodo Unite for VPN access with friends and LAN gaming. However, just recently the program stopped working correctly. I have reset my configuration, tried multiple different settings, and nothing at all has remotely worked.
View 3 RepliesI have been using a d-link router for some time now and since yesterday it has stopped working ( I have an orange 'world' light on all the time) After looking around this site I have tried resetting etc and nothing works. If I plug the ethernet cable into the modem I can get on the internet if I plug the cable into the router then nothing. These are the details I got from the config all when I plugged the ethernet into the router.
View 3 Replies View RelatedMy router suddenly stopped working yesterday and I've tried everything I can think of to fix it. I have one computer wired directly in to it and a few laptops that use wireless connections.The power LED and the internet LED light up, but the status LED and the WLAN LED do nothing. Pushing the factory reset button on the back doesn't seem to do anything.Can't connect to the router site (192.168.0.1) The internet works fine when I plug in to it directly, so its definitely the router.
View 3 Replies View RelatedI have a Dlink DIR-615 wireless router that up until a few days ago was working perfectly. Then I had to turn it off at the wall before a storm and it has stopped working. I have tried resetting it with no luck. I am able to get internet try to get onto on my desktop without the router.I have tried to connect to 192.168.0.1 it won't let me. I can't get on there with an internet connection either. As soon as I connect the router the default gateway disappears. [code]
View 5 Replies View RelatedI bought the DIR-655 less than a year ago in Amazon, shipping it to NY. And then I came back to Uruguay. Almost 3 months ago the router stopped working completely and I started to search for support in Uruguay.After calling US support I was told I should contact the local or regional D-Link (which I later found is D-Link LA). And via DLinkLA.com I found the company TELEDATA S.A. url... who does the official support for D-Link in Uruguay. They told me the router couldn't be fixed, and told me DLinkLA, which is based in Chile, would either send me a working one (they also told me the service/warrany was already approved), or send me the money and gave me their contact details.After two weeks of contacting them, trying to get their attention, they finally told me it was not their responsibility because it was bought in the US. And now they don't return my e-mails.
View 5 Replies View RelatedI have a Dlink Dir-615 router and a Motorola SB6120 Modem. For some reason the router suddenly says it's receiving internet access from the modem. It has worked for several months beforehand. I tried another Dlink modem and got the same results. I have my computer hooked directly to the modem hence the ability to make this post.
View 5 Replies View RelatedIt seems that motion monitoring setup for 930L is not working correctly.I've setup the camera to ONLY monitor the half of the screen, but it is still monitoring the other half of the screen as well.I've setup the camera to FTP the messages when motion is detected, and it is uploading the images when the other half contains the motion.
View 6 Replies View RelatedRegion : Hungary
Model : TL-WR740N
Hardware Version : V4.20.0
Firmware Version :
ISP : T-Home
I bought a TP-Link TL-WR740R Router, the setup went smoothly, I could connect to the internet and set up WiFi connection. But after a few hours, I accidentally unplugged the Ethernet cable from the router, and since then, I can't seem to make the router work. (I obviously plugged it back in.) Setup says I have a problem with the WAN connection.I tried rebooting, resting, reconfiguring, cloning the MAC address.The router is sending packages, but receiving none. How could this happen just by unplugging the cable for a second?
I have a program Eric's Movie Data Base. It needs to go to IMDB to update very often.On my XP there is no problem, it connects quickly every timeHowever I need to run it on my laptop with vista with a wireless connection.Using Vista the program EMDB runs ok but cannot connect to the IMDB site via the program.I have checked and firewall is off, and UAC also.As xp has no problem ( both are usin the same router) I can only assume Vista is blocking it.The request is reaching my modem, and the router is not using any port forwarding.Error message in log isFIREWALL replay check (1 of 24): Protocol: ICMP Src ip: 94.64.148.77 Dst ip: 58.166.25.196 Type: Destination Unreachable Code: Port UnreacheableI have contacted the developer who says the program is using the IE engine.
View 14 Replies View RelatedI have a program that is supposed to talk to a server. I basically need to see how it behaves in the worst of circumstances. I need something to mimic this kind of behavior by adding "artificial" high latency to the program. Is there an easy to use program that connects to a the adapter that can do this kind of testing?
View 1 Replies View RelatedMy DIR-655 wireless has stopped working after a few years of flawless operation. It still works for wired operation. I was running Firmware 1.21, tried rebooting, resetting to factory, powered off the unit, etc. without success. Decided to Upgrade to the firmware to 135 NA, still no success. I am in British Columbia on Shaw Cable. On the Status Page under Wireless LAN, the Wireless Radio shows "Init failed".
View 3 Replies View RelatedI've had the dir655 for about a year now, and no problems at all, until about a week ago. I went into a couple of online games (Bad Company 2 and World of Tanks) and would have a low ping showing in the game, but every 10-15 seconds, especially in areas with a lot of action, I would get large amounts of lag, making the games unplayable.I would be unable to move or keep getting 'teleported' back 20 feet. I looked into it maybe being the servers, steam in the case of bad company, or my internet provider, but regular internet actions are not affected at all. After searching for a while tweaking settings, turning off antivirus and firewalls, it made no difference.I finally today plugged my modem directly into my pc instead of leaving it on wireless, and all the problems go away. All packet tests and connection tests to my router have come back with no errors. Again, I have never had a problem just browsing the web or watching videos, and usually get more speed on speedtest.net than my provider even advertises. I also upgraded the router firmware.I tried going into my router settings and doing all I could (as I understand it) to have exceptions, port forward, and even did the one thing (can't remember what it's called) where you add one ip address that will have no limitations put on it by the router, and none of this has made it work.
View 9 Replies View Relatedrecently my network adapter just stopped working. The wifi signal was really bad so i unplugged it and when i plugged it back in it doesnt even turn on. I've reinstalled the drivers and still it doesn't turn on. In device manager there is a yellow exclamation mark next to it and when i click on properties it says code 10. I used it on my laptop and it turns on but when i plug it in my desktop it doesn't seem to turn on.
View 1 Replies View RelatedI have a DIR-825 (B) for over a year now. This morning, the wireless on it suddenly stopped working. Meaning, all my machines not longer seeing the signal from that router. If I hardwire to it, it will work fine. I have check the wireless settings and they all look fine.
View 2 Replies View RelatedI have a Comcast modem and a DIR-655 router. I finally got them to work together (it took some doing!) and now the router has stopped working with my Roku player and laptop. It still works fine with the desktop that's wired into it.
View 6 Replies View RelatedMy DIR-655 stopped working after updating firmware to 3.35. Only power light comes on. port4 flashes for a microsecond when I plug it in. Recovery mode has not done anything. Computer acts like nothing is connected through Ethernet, says "No Cable Connected." Only power light stays on the whole time. I am guessing this thing is broken now. when i go through ipconfig, "no media connected." If not whats a good router under a hundred bucks today, had this router since early 2007.
View 10 Replies View RelatedI originally bought the 615 router because my Net Talk telephone required it. The first Wi-Fi device I used is my Kindle Touch. I have been able to use the Wi-Fi several times since I received the Kindle, but there have now been two failures to connect. The first time I just unplugged the router power and connections, restarted the modem, and rebooted my computer. The Wi-Fi then worked. Now I am experiencing a failure to connect again.
I have noticed that when I restart my computer I have to connect to the internet directly by pulling the cable from the router and putting it from the modem to the computer. This seems to teach the router what it is supposed to do, because when I reconnect the modem to the router the internet starts to work immediately.I have tried changing the password to wireless internet, but my Kindle still will no longer connect. The router is about two years old. [code]No go to the devices and check to see if you see the new SSID name you gave in the router. I should be listed there. Select it and it should ask you for a password, enter the password you gave in the router. The only problem is that my modem does not exactly say "mixed G and N".
I was changing the port forwarding configuration when suddenly the router stopped working, and now the "D-Link" light is constantly on, and the power light and the 4 LAN lights are flashing. Nothing worked, resetting, or unplug and plug again in a short time.
I disconnected it for 12 hours, and when I plugged in again, it kinda worked, and the settings where factory defaults, so when I tried to connect it to DSL via PPoE, when ( I believe ) it reboots to accept the changes, it starting flashing again and completely stopped working.
So I waited 12 hours more unplugged, plugged it and it worked, and the setting from 12 hours earlier were still there. But when trying to connect to the DSL it stopped working AGAIN.
Now I don't know what to do. I guess I am going to keep trying connecting with little differences, until something.
I believe it still has warranty but since the is no official service in Uruguay, it isn't economically viable to send it overseas.
I am currently connected directly to the DSL, sharing connection to other computers through a switch and hosting an ad-hoc wireless network, but the performance is terrible and the wireless range is minimal.
I have had a setup in which my four DCS-930Ls transfer picture every 15 minutes over a Dovado-router connected to a mobile broadband modem. This has worked perfectly until this last night. No pictures are transferred and upon using the test FTP function the status page just says "Testing ...." forever. I've also tested e-mailing picture without success.
View 2 Replies View RelatedI was working on the computer and internet just stopped, checked the router and it doesn't show up in air-port pref on my Macbook Pro anymore. It was still on my iPhone, and then a few minutes later disappeared from my iPhones network as well. I've tried hard resetting etc, network name doesn't show up anymore, on ethernet to the modem now but tad uncomfortable sitting on the living room since I have the router and modem in my entertainment center.
All the lights work fine, and it lights up like normal but network went "poof".
Typing in ip of 192.168.0.1 just says google chrome cannot connect to that page. I had to play with my Mac for awhile as it wouldn't connect by ethernet till I figured out I had to uncheck passive FTP from Proxies.
Since a couple of weeks I have a linksys EA6500. When I go to the device list to see which devices are online the device list is not displayig the correct data. I see devices online that are offline and also devices are offline that are at the moment online. When I try to delete a device that is offline in the list I get error 2315. I have that error in the local and cloud interface. The list has a frozen state from a particular moment.
When I reboot the router then all devices in the list have status offline and the device list stays that way. Nothing gets online anymore or will be added. When I reset the router to factory default all keeps working without problems for approximately 24 hours and after that the problem occurs again. The list freezes again and you are not able to delete a device.
I searched the forums but no one has this problem. I only can find a post that describes my problem but for them a reset worked. In my case a factory reset works also but the problem keeps coming back.
The other day I went to a friends house, came back home, booted up my PC, and my wireless network adapter wasn't working. I've tried everything to fix it.It's a D-Link DWA-525 802.11n Wireless PCI netowrk adapter. On device manager it just says 802.11 Wireless LAN Card with a yellow exclamation next to it. And when I check what the error is, it's either error 31 or 52 at different times, depending what I've tried to do to fix it.I tried downloading the driver for it off the D-Link website, nothing happens at all when I install it. I tried taking it out of my computer and plugging it in. I tried enabling it and disabling it on device manager.I noticed one thing, when it's in my computer the green light at the back that says activity next to it isn't on.
View 10 Replies View RelatedSG-300 52 native VLAN blocking network packets
View 3 Replies View RelatedRandomly my router stopped working in the middle of the night. I didn't think the issue was with the router so i called the Tech Support people from Brighthouse and they told me to connect directly to the modem so i did that and I had internet. But why would my router randomly stop working, I've had this Linksys Dual N bound router for a year and never had a problem with it. I want to think that its the internet providers fault but I guess I really don't know.
View 2 Replies View RelatedMy Linksys router stopped working. Resetting it didn't restore it.I bought a new Linksys E4200 router and configured it to the same settings as my old router. However, now I can't access certain website like Hotmail, Facebook, a weather site and others.But I can connect to most other websites, stream video, etc. Any suggestions why I can't connect to Hotmail, Facebook, etc???? I have 4 computers (3 wired, 1 wireless) connected through the router and they all do the same thing.
View 5 Replies View RelatedMy wireless router stopped working. diagnostics messages say it could be either bad ethernet cable (not the problem as I am using the cable right now to plug directly in to cable company modem to gain access to internet) OR "drivers not being recognized"
View 1 Replies View RelatedWe have two laptop computers and our Tivo hooked up to use the wireless internet through our cable company with a Belkin router. Over Christmas we got a camera that emails directly from it, and it told us to press the WSP button on the Belkin router. The camera magically worked, however our computers did not work anymore! After an hour long phone call to Belkin, I got one of my computers to work normally again. However the 2nd laptop won't connect to the internet and our tivo isn't picking it up either, which mean our shows are not recording.
Also, I'm using two apple computers. When I attempt to hook up the airport network, it says "unable to join the network."
it stopped booting up and now i cant talk to it.
View 5 Replies View RelatedI use the Windows7 Virutal WIFI when traveling abroad to give my Iphone an internet connection in my hotel.I've had zero issues until this week. The WIFI connection is still showing up on my iphone, but I no longer get internet access (I only get an IP and subnet on the iphone now, no router or DNS info). The issue began (coincidence or not) as my MagicJack downloaded and installed a software update. MagicJack support says they aren't the issue. I experimented with created an Ad-Hoc network...no change. I've removed and reinstalled the wireless card and driver. No change. I suspect some corruption with ICS, but haven't found any solutions online to fix it.
Microsoft Windows [Version 6.1.7601]
Copyright (c) 2009 Microsoft Corporation. All rights reserved.
C:ipconfig /all
Windows IP Configuration
Host Name . . . . . . . . . . . . : Richard-PC
Primary Dns Suffix . . . . . . . : MARCOGROUP.local
[code]....
I recently aquired a 2nd AP1140, however when i configure it for WPA 2 it works inconsistent, a ping for example will work only for 33% of the time.The same client has no issues with my 1st AP using WPA2, with the 2nd AP WEP works without a glitch.
View 2 Replies View Relatedwe are running CiscoPrime LMS 4.1 and I have the following problem.I have configured SNMP Settings as shown below (the order of the targets is exactly as it is configured on the server):As can be seen we use three different read community strings. I also have exluded a bunch of IP ranges and IPs from the filter settings. When I manually start discovery everything works fine, meaning that all devices in the above ranges that need to be discovered are discovered as "reachable". The problem appears in the scheduled discovery (happens once daily). In that case only the devices with Read Community snmp1, get discovered as "reachable". All other devices with Read community snmp2 & snmp3, as well as those that are excluded in the filter settings, are discovered as "unreachable".The discovery uses DCR as seed and seed devices are also configured.I also have a problem with PingSweep in the discovery, but I will open another discussion so that I don't complicate this one too much.
View 1 Replies View Related[CODE]My router stopped working when I tried to connect my new Samsung Smart TV to the wireless network by using the menu on the tv. I had to go and press the WSL button on the router. I pressed what I though was the WSL button and now my router doesn't work. I has three lights lit up, the power on light, a small green blinking light and an amber light by the number 1.I've gone to the Netgear website and they want $69 for assistance to get my router up and running. I can buy a new router for that much money. There has to be an easier way.
View 2 Replies View RelatedI have a Century Link modem connected to a Linksys router. I have three computers hooked up wireless. I used another computer to hook up with the ethernet cable because that wouldn't work wireless for some reason. A little while after that, the Linksys network stopped working completely(all three computers could not access the internet). Now I can only connect to the internet if I use a ethernet cable from the modem.
View 2 Replies View Related