I had an SMC router before, and I replaced it with this new D-link DIR-655, The problem I am now having is that I used to visit a web based e-mail /OWA Outlook Web Access, After I VPN to my company, but now with this new D-Link after I VPN, I lost the capability of accessing my OWA to read my e-mail
View 1 RepliesHow to access remotely over the Internet to office PC from my home PC and get files that I need? Office's ADSL modem's model is BeWan iBox V1.0 and it has a built-in firewall. ADSL connection has a dynamic IP, which I assume should be configured as static (but how?) Should I investigate VPN capabilities as well? I'm not very knowledgeable about these things.
View 7 Replies View RelatedI run a small organisation with 4 pc in LAN with a D-link DES 1016E router, and of course Internet connection through BSNL Broad Brand with a dynamic IP . Kordil EDMS, XAMPP is installed in one of this Pc with XP Pro SP3 and IIS7. I want to establish a easy and Free system through which i can connect my office server from anywhere through browser for editing ms office files at my Office network. suggest a step by step guide. I don't have any system administration knowledge. i have activated Remote desktop, but whenever i am connecting through internet my DSL router configuration page is opening.
View 1 Replies View RelatedMy home network consists of a Linksys WRT54GL router running DD-WRT supplying wired access to my desktop, a bridge to another WRT54GL (also running DD-WRT) to provide a wired connection to a XBOX upstairs, and wireless access to about 5 or 6 different devices including several laptops, an iPad, and an iPod touch. My question is this:
I am adding a 22" TV into my office so I can watch TV while working on my desktop. I only have one cable jack in my office which is currently plugged straight into my cable modem. This means I'll have to use a splitter to give both my TV and modem cable access. How much signal degradation or speed do I stand to lose or should expect to lose?
I have a very high speed connection in my dad's office, and it is over 10 mbps. and the connection in my house is worse ( 256 kbps ). So can I use the office connection in home without any problems from the ISP. just like sharing the connection from the office to home.
View 7 Replies View RelatedI have this strange problem the application Whatsaap connects at my office wifi perfectly but at home it does not connects,I don't know what seems to be the solution.
View 2 Replies View Relatedlooking for opinions on a Wireless Access Point/Bridge/Repeater/Router I might buy and setup for a the home workstation, few wireless devices, and future add-ons.
Product;
EnGenius ECB9500 Wireless Access Point / Bridge / Repeater / Router with Gigabit & 802.3af PoE,
IEEE 802.11b/g/n ,
Up to 300Mbps ,
WEP Encryption 64/128bits
WPA Personal (WPA-PSK using TKIP or AES)[code].....
I wanna setup a small office network ? how do I setup and can I use a printer on this LAN ??
View 3 Replies View RelatedIf we remove lan card from office and fix it in home machine so the ip address is same or it will be different?
View 1 Replies View RelatedWould the above router be a good choise for a home office setup for use with WAN speeds upto 30Mbps and VOIP? Any other.
View 1 Replies View RelatedI am not sure what the problem is but my laptop wont connect to the wireless in my office, it connects fine to my wireless network at home..
View 13 Replies View Relateddo not have fast internet service so we must need to combine two or more different internet providers and get one speed kindly reply do you know any router/modem/switch which can do this for us.
View 2 Replies View RelatedI have my laptop. I need to use my broadband connection at my home. Also I need to use my laptop with wifi at my office. We do not have any dhcp servr at office. What I am doing now is changing ip configuration at office every day manually.
View 2 Replies View RelatedI have recently managed to configure a setup where I have 2 srp527's one at office one at home.Have 1 fixed IP at the office and 1 fixed ip at home.I have configured the srp at work to be a vpn server and have configured the group and 2 user profiles. This allows me to have 2 concurrent sessions over the vpn to my office from desktop and laptop at the same time. Connections fire up perfectly no problems.From the desktop, I connect using vpn client with user profile 1 Once connected, I then connect to my workstation machine at the office using remote desktop.This gets me super fast access to office files and large spreadsheets without downloading the whole file over the vpn and is working perfectly.
If I then additionally connect from the laptop using the vpn client with user profile 2 the remote desktop connection drops.Disconnect the laptop connection, remote desktop comes back.Have isolated this to being 2 connections arriving at the srp at the office from the same external ip. If I connect my laptop to my phone as a hotspot rather than using my home LAN, both connections are made and remote desktop has no interruptions. Is there a way I can overcome this through re-configuration of the srp at the office or is this a limitation with the srp?
I have a group of five computers at one end of my home office and another group of four computers across the same room. All are hardwired on the same internal network. These cannot be consolidate or moved into one corner or closet. There just is not the space and it's just physically not possible.There is one Internet router as provided by the local cable company. I have this connected to a LinkSys WRT54G2 broadband router. A Netgear DS108 8-port hub is connected the LinkSys. All computers either connect to the Netgear hub or to the LinkSys router. As of now, the WiFi from the LinkSys router is only ever used by my cell phone while at home.
This set up is annoying. At first I did not mind, but there are cables on the floor that I have to step over. These CAT5 cables connect one set of computers to the LinkSys or Netgear. I have to watch where visitors are walking or stepping to assure they don't trip.How can I keep these computers on the same network and eliminate just those cables crossing the floor of my home office?Should I use WiFi NICs? Would this overwhelm the WiFi on the LinkSys?
I want to acccess my office computer from Home PC.I have ZTE DSL Modem + Wireless Router and got new Static IP, so how to configure Static IP From BSNL.
View 3 Replies View RelatedI have a Windows 7 Laptop that need to be able to join a Home Workgroup as well as an office Workgroup. How!
View 1 Replies View RelatedHere a have a quest that can't find the perfect solution for a half year now.I have one machine at office and one at home, both Windows XP SP3, ADSL connection with static IP.On the office machine a have an archive of about 250 GB of files.When i am at home sometimes i need to connect to my office machine, search through those files, maybe preview some, and then download some needed files to my home machine, using a download queue feature is possible.The task doesn't seem so complicated, yet, i did not find a perfect simple solution so far.
View 5 Replies View Relatedi have a cisco router 887 which i am trying to configure. but however, do i really need to use the SDM utility or i can do it through CLI?i need to replace my current router in my small home office.
View 3 Replies View RelatedI am connecting to a ASA5505 at from home to the head-office using L2TP VPN.
Head-office then has a connection to other-office via a site-to-site IPSEC tunnel.
When in the head-office (192.168.100.0/24) I can ping/access remote-office (192.168.200.0/24) OK.
When connected remotely to head-office, I can ping/access head-office OK from the road-warrior laptop.
My problem is that when connected remotely from home to the head-office I cannot ping/access the other-office subnet.
On the home laptop the L2TP VPN connection is set to route all traffic to the VPN connection using the HQ as the internet gateway I can confirm this works.
I cant do traceroute (I get timeouts) as my policy doesnt allow and not sure how to enable this properly on the ASA.
names
name 192.168.200.0 othersite
!
interface Vlan1
nameif inside
security-level 100
[code]....
I just installed a 10 port Cisco SG300-10MP in my office, 9 of the ports are already in use. Connected to it are
PC
Laptop
Notebook
WIFI AP
B&W laser printer
Color inkjet printer
IP camera
Squeezebox SB3
Cat5e connection to basement HP 1810G-24 switch All of these devices are connected via a single Cat5e cable that was installed when the house was built. I had to re-terminate both ends of it when I moved in because the existing terminations were done very poorly. I have no idea how or where the cable is routed, nor what the quality of this Cat5e cable is. It did pass a test using my cable tester.
This single Cat5e is connected to my main HP switch in the basement equipment rack. Both of these switches have mini-GBIC ports that can utilize SFP transceivers and fiber. I priced out 2 MGBSX1 compatible modules along with a 30M multimode fiber patch 'cable' online at under $150. Although it would require at least a couple hours of work (including digging around in the attic and crawl space and drilling some holes), but running the fiber to the basement is very doable.
My question to my far more experienced forum members is if the performance gains would be worth the effort?My server is in the basement, and despite having an Intel GB NIC in my PC I am seeing read speeds of ~23MBs and writes of ~49MBs to/from my it. My server has teamed GB NICs (802.3ad LACP Layer 2) connected to trunked (LACP) ports on my HP switch.
I have a home office with multiple VLANS/subnets I have many VPNs that connect only a specific subnet to a specific remote offfice. On a 5520, can I create a S2S VPN to different remote offices that have the same IP scheme, but from different home office subnets? For example at my home office let's say I have two independant, distinct VLAN/subnets: 192.168.140.0/24 and 192.168.150.0/24. Can I create an S2S from the 140 subnet to a remote office with a 10.10.10.0 addressing scheme and another S2S from the 150 subnet to a totally different office also with a 10.10.10.0 scheme?
View 1 Replies View RelatedI have a TP-Link TL-WR720N wireless router, and I am trying to set it up so that it limits the times that my kids can access the internet. I have included screenshots of all of the programming pages, so you can see exactly what I am looking at. Here is what I have done so far:
Schedule: I created several schedules for different days, weekdays, weekends, start at 1900, end at 2100, etc.
Host: I created a host name titled "All", and set it for 192.168.0.3 ~ 192.168.0.199. The router assigns from 192.168.0.2 thru 192.168.0.199. I assigned my computer's MAC address as the "Parent PC", and bound it to 192.168.0.2, through the "IP and MAC Binding" function. In this manner, I hope to limit the kids access, while allowing the parent PC to access it at any time.
Rules: I selected the option to "Allow" passing of packets during these hours. I then created rules, assigning the host "All" to the different schedules that I created. I set the target as any, and did not set up any targets in the target section, because I do not want to control what sites they visit (yet, anyway). I generally don't worry about the sites they visit, I just think they spend too much time on the internet.
Here is what happens. I use my laptop (not the parent PC) as a test machine. When trying to access the wireless, i have verified that the router does give me an IP address within the specified range I created in the schedule. If I set the Access Rule to "Allow" the packets to pass through the router, and try to connect during the time it is set for, it will not allow my laptop to even connect. The weird thing is, if I set it for "deny", I can connect, but I have no internet access. Either way, if I have any of the rules enabled, I cannot access the internet at all. Thinking maybe there was some sort of conflict with schedules, I tried enabling only one of the rules instead of all of them, with no change.
What am I doing wrong? Do I need to set targets? If so, does this mean I have to set one for every site I want them to be able to visit? Can I set a target as the IP address of the router? If so, what ports do I use?
I am looking for an equipment recommendation for setting up an access point/repeater for my home network.
I have comcast > surfboard > d-link dir 655 I want to add another router/access point so I can move the dir655 to my office and have my computers connected over gigbait. All my comcast stuff is setup in the living room, and I would like to setup the access point there. Something like
comcast > surfboard > ddwrt n-router (living room) > dir655 (in office) > desktop
I've been having this issue for quite some time on my Windows 7 SP3 x64 machine. It's a desktop, connected via ethernet to a TP-Link WR740N router, that also provides wireless coverage. My ISP is a local one (the country is Latvia), and it offers a decent 100 MBps up/down optical fiber internet service. Now for the problem - there is only one home network on my computer, that seems to work, and that is 'Network 2'. Whenever I have to reboot the router for whatever reason, it attempts to reconnect, but sometimes reconnects to a 'Network 3' and once even to a 'Network 4' and 'Network 5'. None of these other networks have internet access. I tried to run the diagnostics tool on the issue, and usually it told me that there's a problem with the default gateway. Additionally, twice I've had the issue of the computer completely freezing when connected to one of the Internet-less networks (eg 'Network 3'), and trying to disable the network adapter, forcing a restart that consequently caused a fail boot - from there on I had to use System Restore to actually get my PC to function.
The way I've been fixing it, apart from random rebooting, reconnecting, and hoping for the best (that it decides it wants 'Network 2'), is by putting in the Resource Mini CD that came with my router, and running the Wizard for the WR740N router. It has 4 steps, the 2nd of which is 'Installing the router' (configuring the network adapter), at which point, my internet starts to work (always connects to 'Network 2'). If, I however, decide to continue this process to the step 'Configure router', and attempt to set up my wireless connection, it will begin to reset itself, and once again connect to 'Network 3', leaving me without internet access.
I have just bought a TP-Link Wireless Access Point (TL-WA&01ND) and an ethernet switcher (TL-SF2005D).I have put the access point into client mode, allowing me to put it in my room and wirelessly connect to my router, allowing me to plug my PC in over ethernet and use the internet. However, after much fiddling with settings I cannot get it to work, as it continually searches for a network, and then fails to connect, despite the fact it is configured to use the network?I already have a similar setup with a netgear wireless G access point which works, and so I dont understand why the new box cannot do this when using what I believe to be the same settings.
Secondly I have an ethernet switch box which I bought to connect to the access point and switch the ethernet signal between my two PCs, my xbox and PC. This works fine with my primary PC (over my old access point) but when I try to connect my PC i get a DNS failure with auto IP settings and a gateway failure with manual settings, and other devices refuse to connect.
My home desk top is set up with D-Link Xtreme N Dual Band Router. I have no problems accessing the internet on my desk top computer. I am trying to access my home wireless network through my HP laptop computer. The wireless network status is Limited or no Connectivity. I've tried the "repair" button with no resolution. The wireless connection is set to automatic.
View 1 Replies View RelatedI have a wireless router (D-Link DIR-625) connected to the modem for our high speed DSL. I have two Brother MFC printers, one is a laser (MFC-9420CN) connected w/ a Cat-5 directly to the router, the other is an ink-jet MFC-6490CN and I would like to use it wireless....but I could connect it to the router if I need to.I have wireless connection to the internet, from my HP 32-bit PC (running Vista-Ultimate), but can not see either of the printers on the network, and cannot print to either. I manually configured both to have an IP within the range of my network, but they still do not work.The problem (I think) could be with the IPCONFIG. (I had no problem last year, but we recently had a few power outages, and now the PC doesn't seem to 'see' any of the printers.) I checked the IPCONFIG. it states 'media disconnected', but I can ping the one wireless printer??? I can not ping the laptop on the network or the laser printer (I confirmed it's ipconfig before pinging).
I know the network card can't be bad, or I couldn't get to the router to access the internet. I also went into the cmd prompt as the administrator and did the /release/renew/all but that didn't work either.
We currently have a 3/3 Etherloop. We dont have any internal IT as we are still small and while not a networking guy I can at least understand what is going on. Right now at peaks we are hitting 100% utilization.
We run a call center in house so I am trying to determine at the very least how much of this traffic is from voice data compared to everything else.Was running through our networking configuration and it just seems off to me. The following is the flow.
-Etherloop Demarcation >
-Cisco Integrated Access Device >
-D-Link DIR 655 Wireless Router >
-24port HP Procurve switch >
-24port HP Procruve switch >
Everything up to the first switch is a single line. The first switch has all ports running out except 1 which goes to the second switch. The second switch runs out to machines as well.
I am at the networking level where I understand a switch but have no idea what the IAD really does between the etherloop modem and the wireless router.
For some reason I feel like the router should not be setup in that manner and should be off of the switch. With the cisco IAD running directly to the first switch. So my 2 big questions are.
1. Does this setup even make sense.
2. Whats the easiest way to monitor traffic, at the very least it would be nice to see real time up/down and be able to log in. Then I guess using ports figure out what is being used by voice. My first guess was just putting a machine between the IAD and first switch and monitor and log the traffic.
i got one thing im in my office we have limited inter net acess but people are using much so i want to control the net. once only office hour
View 1 Replies View RelatedRegion : Spain
Model : TL-WR842ND
Hardware Version : V1
Firmware Version : 3.12.22
ISP :
I am trying to set up a VPN access to the office Windows network by setting the pptp options in the WAN area of the networks settings.
I have entered the public IP address of the office network and also the username and password required by the system. When clicking on the connect button the router attempts to connect but then returns a "disconnected" message.
I have a cable modem in the basement and ethernet lines to two offices upstairs.I have a 4-port wireless router and a 5-port switch. I have a computer in each office and a NAS in one of the two offices.There is no direct wiring between the offices. I want to have internet access and access to the NAS from both offices. Will the following configuration work without having to go to Static IPs? 1) Modem01-> Router01->Switch01->Computer01; 2) Modem01->Router01->Switch01->NAS01; 3) Modem01->Router01->Computer02. If not, what needs to change?
View 3 Replies View RelatedRegion : India
Model : TL-WR740N
Hardware Version : V4
Firmware Version :
ISP :
I have been using this router for around 8 to 9 months now. Everything was working fine till one week back. Now I am facing problem with my office emails. I cannot get my office emails while on WiFi network. Outlook is not able to connect to my office server and I don't receive my emails. Rest everything works fine. Initially i used to get all the emails while using this WiFi router. When I connect my internet cable directly to my laptop, i am able to receive all the emails in my office outlook inbox.
I am also using my Samsung Galaxy S3 on this WiFi network. And my office outlook is configured in it. I am facing the same problem with my phone as well, it started recently, around one week back, as already informed above.However, when i switch on my mobile internet, all the new emails start coming to my inbox, which means that there is some problem with WiFi network.
What I am supposed to do which will enable me to receive all the office emails while on this routers WiFi network. Its giving me a hard time.