D-Link DIR-655 :: Not Getting Gigabit LAN Wired?
Jan 7, 2011
DIR-655 Firmware: 2.00NA (most recent) Hardware Version: B1 I am not getting Gigabit LAN wired. I am only averaging 25% of that, which means 256mbps or 32MBps. note the following:
- Router only connected to two computers (wired), wireless turned off
- Cable length does not exceed maximum specified length of 100 meters (328 feet). Neither does it exceed the usual maximum length of 100 feet. (both ends)
- Cable is CAT 5e (both ends) allowing Gigabit speeds
- NICs on both computer are able to run at Gigabit
- Both computers recognize the Gigabit connection speed
- Sustained Hard drive speeds are rated at 101.9MBps and 86.6MBps or 815.2mbps and 692.8mbps (therefore, connections should run at least 692.8mbps or 69% usage)
- Minimal programs were running in the background (in fact, almost nothing except for the OS itself)
- Windows 7 on both computers
- Later, I ran a streaming of a file and transferring files over the network, the speed still remained around 25% usage, which means there's isn't a cap of network usage per program. (is there usually a cap?)
Things I don't want to hear:
- Cat 5e doesn't support gigabit
- Check cable has 8 cables instead of 4 (it has
- CPU not good enough (it's plenty fast for copying files, quad and hex core)
- Not enough RAM (plenty of that too, I don't know how much role RAM plays in transferring files over the network)
View 12 Replies
ADVERTISEMENT
Jan 24, 2012
Adding ports to my Fairpoint provided Westell 7500 Rev D DLS modem router which has only 4 RJ45 ports. Bought a Linksys SE2500 gigabit smart switch but it doesn't assign IP or pass on router assigned IPs. Can't get ASSISTANCE from Fairpoint [successor to Verizon] configuring router or any advice on other ways to get more wired devices on LAN.For speed in backups I'd like 3 devices to be able to communicate at giabit speed Want to have an NAS and 2 Win7 Ultimate computers on smart switch, 3 other wired devices [WinXP, AT&T Cell tower, & DirectTV whole house SWM interface] and wireless on the router. 1. Are Fairpoint specs for DSL published so I could get another DSL modem router instead of the Westell or is it better to configure Westell as a router only and use a new to be acquired router with or without the existing or a new gigabit switch. I have a DI-624 from the pre-DSL Hughesnet satellite days.2. Are there less smart switches which would work better and let router assign the IPs?3. If this is too complex for me, can you recommend a remote access consultant to walk me through this for a fee?4. I'm 82, have been in computing since 1960, mainly in on-line end user environment mbut don't know the bridging, PPP PPoE differences, and implementation or configuration details of current hard and software except as a user.
View 2 Replies
View Related
Sep 10, 2011
I'm currently using onboard lan card of P6X58D Premium. However in the Cisco web setup page or even in my Windows 7, it shows only 100Mbps connection. I tried to force to 1000Mbps but it failed to get an IP. I did a google and found that may be the router doesn't do well with Intel card, but I use another onboard lan card with Nivida chip+AMD CPU, it's still only have 100Mbps. What can I do to have a 1000Mbps connection?
View 5 Replies
View Related
Jan 30, 2013
Is it possible to configure the RV042G so that one WAN port is connected to an ISP with a static IP and the other to an ISP with a dynamic IP. Then, I would like to setup a VPN tunnel and use the static IP for that and have all the other internet traffic go through the dynamic IP.
I know I could set it up with the static IP as the primary and the dynamic as the backup. Then, if I lost connectivity on the static IP, I would still have internet access, only the VPN tunnel would be down.
View 1 Replies
View Related
Aug 6, 2012
I have a Netgear N600 WNDR3700v1 Dual Band Gigabit router and am having a problem with the wired connection with my PC. Everything wireless in the house works fine. In fact, I also have a Direct TV box hooked up for on demand and a sling box hooked up (both wired) and they work find. It's just my PC that is having issues. If I bypass the router and hook straight into the modem, it runs fine also so I have something going on between the router and this PC. I updated the NIC driver and this did not work. Before the update in the device manager, it said it was a NIVIDA nForce Network Controller (if I remember right) and now it says NIVIDA nForce 10/100 Mpbs Ethernet. It was suggested that I change my speed and duplex to match the router after I update but I am unsure what to change it to.
View 11 Replies
View Related
May 7, 2012
Is it possible to run the EA4500 as a Wired only Gigabit router? To do this do I just go into the settings and disable both the 2.4 and 5 channels or do I have to do something else?
View 2 Replies
View Related
Sep 26, 2012
I have an Ethernet Loopback Plug (4 Pairs) made and trying to test the Gigabit Interface on a 3845 Router with a fail result. The interface will show up/up only if I set the interface to 100M/Full Duplex when I plug-in the Ethernet Loopback Plug (4 Pairs). I don't see this Gigabit Interface @ 3845 router has any option to set it to internal or external loopback.
View 2 Replies
View Related
Nov 23, 2011
I'm running an Optiplex 330 with the Broadcom NetXtreme 57xx Gigabit ethernet card.
The computer is running Windows 7, 64bit, but there do not appear to be any drivers for that OS.I tried selecting Vista 64bit, but there were no drivers. The Vista 32bit doesn't work.
Then I went to Broadcom and found these drivers: [URL] the W764bit drivers didn't change the fact i'm still on a 100Mbit card (as seen on Local Area Connection Status screen and the Device manager)
View 1 Replies
View Related
Jan 8, 2011
I've got a Buffalo LS-WXL5BF connected directly to one of my PC's gigabit ethernet ports. The link in the Win7 network and connections is showing it connected at 1Gbit but the actual transfer speed tops out around 150-200 Mbit or roughly 15-25MB/s (which is well under what the unit is advertised to perform at.)
I'll be swapping out the cable that came with it for a good CAT5E I got from monoprice but other than that I'm not sure what to try.
View 15 Replies
View Related
Mar 9, 2012
I have a D-Link N 300 Gigabit Router. It's only allowing me to download like 30 MB at a time. If I bypass the router, the internet works just fine.How do I fix that?
View 1 Replies
View Related
Jun 13, 2012
My router is on a static IP, it is a Linksys WRT150N, and it doesn't have gigabit ports. Is it possible to run it through the 1522's gigabit ports.Modem -> 1522 -> actual router.
View 2 Replies
View Related
Feb 13, 2011
my problem is that i have a computer connected via gigabit lan with a cat5e cable.i have a notebook with a d-link dwa-140 usb wifi adapter connected.and the max transfer speed i get is 14 mbps. d-link dir-655 firmware 1.34eu.in windows it reports 300mbps.in the router it reports 270 mbps sometimes 300. the settings in the router is 40mhz only,. ch 13. wpa2 aes. as described in the sticky.the devices are within 3 ft of each other.
View 2 Replies
View Related
Aug 8, 2011
I cant figure it out and can not find a solution. All three computers have gigabit nics, I have gigabit router and switch, my d-link 321 is set to gigabit, the only thing on my network that is not gigabit is my printer. I'm not getting gigabit transfer speed from my computer to dlink 321. I rarely do computer to computer transfers, so I dont know what the speed is of that. The best tranfer rate is from 7-12mb. I am also using cat 5e wires on all connections. What am I missing?
View 12 Replies
View Related
May 20, 2012
Whenever I use my router web pages often fail to load. Then after about 30 or seconds or so it will start working again. Even worse,if I go to game online I will have lag like crazy. Even if I am the only one on the router.I'm using a D-Link n300 gigabit router.
View 5 Replies
View Related
May 25, 2013
I recently modified my home network in hopes of getting faster file transfers between devices. But it looks like something's not right.I'm suing Lan Speed Test and the best performance I get over WiFi is about 44Mbps (avg.). From my laptop to my NAS. If i turn off the WiFi and do the test over a wired connection the best I get is 200Mbps (avg.).
1. AT&T 2Wire cable modem. Internet comes in the house through this box and it's currently set up to be in bridge mode so that the TPLink router handles everything.
2. TP-Link WDR3600 gigabit/wireless router set to work in 5Ghz only, 11an mixed mode.
3. WD My Book Network Storage. Wired gigabit connection.
4. Desktop PC. Wired gigabit connection.
5. Laptop PC. Wireless.
6. 1 ipad v.2, 2 iphone v.5. Wireless.
Current setup:
1. internet cable goes into 2Wire Modem.Wireless on this device is OFF.
2. cable goes from LAN port on modem to WDR3600 router's internet port
3. cables go out from router to Desktop PC and NAS
4. all other devices are connected to the 5GHz wireless network created by the router.
View 1 Replies
View Related
Jan 2, 2013
Got 1 Linksys WRT54G Router on the ground floor which uses PTCL DSL Internet and 1 D-Link Wireless N Gigabit Router on the first floor which uses World Call Cable Internet of my house. So yeah we have two internet connections.Getting weak signals from both of the routers in my room on the far left side of the house and little to no signals in the basementSo what I want to ask is that should I purchase better routers or should I go with a signal booster of some sorts like an Access Point or a Range Extender?Also is there such a device which would catch signals from both of these differently configured routers ( different internets, different wireless security keys etc ) and then boost them throughout the house if placed in an area where both the router signals are strong?
View 5 Replies
View Related
Mar 20, 2012
I have a dir-825 and wireless clients connected on the 5ghz ssid can see clients on 2.4 ssid and also out to the WAN (internet) but can't see any clients (my NAS ) connected to the dir-825 wired lan.2.4 ghz clients see everything fine. same with clients connected through the wired lan. I've tried DHCP and static ips. no idea what to do next.I was originally on 2.02 fw and have tried 2.03, 2.05 and now 2.06I'd really like to keep the 5ghz on because I have an AP by my tv and several devices connect from there to stream from the NAS.
View 2 Replies
View Related
Oct 31, 2011
I'm currently using an orange livebox which has been pretty reliable in the past. My set up is livebox > homeplug > homeplug > linksys wireless router > into 2 pcs.Its odd because my pcs have trouble detecting the wireless router, however my laptop can link up no problems.I have plugged my laptop directly into the livebox via ethernet and it works fine so I can rule out the livebox. I've also swapped the cables and they all work ok.Basically, it does link up intermittently and runs perfectly, but then after a day, or even 10 minutes it disconnects and I have a nightmare getting it to work again. I went through the entire cable system and got right to the end and hey presto it all worked...so I plugged my pcs back in. Then after about 10 mins it lost the network connection and I couldnt even link up to the livebox router by keying in 192.168.1.1. The laptop CAN connect wirelessy and access the config pages.
View 2 Replies
View Related
Sep 25, 2011
I just got a DIR-501 and wired it to my desktop. It runs great! (This DIR-601 board is the closest one I can find to DIR-501.)
After connecting the DIR-501, when coming out of hibernation or when booting up, my computer would hang, apparently after the desktop has already appeared (Win XP Home SP3). The first time this happened I got a BSOD with the following:
View 5 Replies
View Related
Sep 6, 2011
I have a Sky broadband router downstairs which has wired and wireless links to workstations downstairs. I have a wired network upstairs in my study. I want to put a router into the study that will link wirelessly to the Sky router downstairs and link the wired workstations to the broadband.
View 1 Replies
View Related
Jul 8, 2011
I have an Internet Connectivity problem which I believe was caused by resetting our D-Link WBR-2310 router. We have a strange, perhaps illogical network setup in our office. Although it was set up before my time, I have figured it works as follows:
(1) A wired/wireless router (let's call it Router A) is connected directly to the DSL modem.
(2) An Ethernet cord runs from this router to a 5 port switch.
(3) 4 cords run from the switch to individual workstations. These computers obtain their IP addresses automatically.
(4) 1 cord runs from the switch to another wired/wireless router (let's call it Router B).
(5) Two cords run from Router B to individual workstations (let's call them Workstations C). These computers used permanent IP, subnet mask, default gateway, and DNS server addresses. I understand that this was done because they could not obtain their IP addresses automatically.
The problem I've caused seems to stem from me resetting Router B to the factory settings while trying to secure its signal and changing its IP address from 192.168.0.1 to 192.168.1.1 (in order to avoid conflict with the modem which has the same IP address). Once I did that, Workstations C could not access the Internet.
I have tinkered with the TCP/IP settings for Workstations C (e.g. by changing the default gateways to the Router B's new IP address), but it doesn't work. What else should I be doing?
View 2 Replies
View Related
Jan 2, 2012
Just upgrade from an old DIR-524 (or something like that) to a DIR-655. Set up was easy all is working good with the computers. |However, I plugged my HP Photosmart C5100 printer into the router (first slot). The computer seems to know it is there, and the printer seems to recognize the router, but it will not printer. Microsoft diagnostics says that the printer is not ON, and the printer is listed on Devices as Offline. The printer is about 5 years old, but it is a trooper and I don't want to to get rid of it.
View 7 Replies
View Related
Mar 1, 2012
Cannot get DirecTV HD-DVR to connect to DIR-655 wired. Any way to get Direct TV to connect?
View 1 Replies
View Related
Mar 21, 2012
Recently replace my DIR-615 (it died after about 3 years of steady use) with the 825.Followed CD setup wizard, adjusted some manual thing as well. Am experiencing slow streaming speeds on various websites. A lot of 'loading' pauses within a youtube video for example when I never used to have any stutter at all on my old router.On a cable internet connection with a standard cable modem (no router in it).DIR-825 FW: 2.06NA HW: B1.Wired connection to router, not trying to steam over wireless.Speed tested at 14Mbps down which is what my provider (cogeco cable) promises.
View 1 Replies
View Related
Jul 18, 2011
I have had my DIR-825 for a year and half. My computer that is wired directly to the router keeps losing the connection to the router - unable to obtain an address. All of my other devices (that are connected via wireless) still hold the connection with no issues. I've checked the cable, unplugged/plugged back into the router, and it shows connection on the network card on the back of the computer.I have used the system interface to ensure the address is a valid one. I have powered up and down the computer multiple times and have also powered down and up both the router and the cable modem.
View 1 Replies
View Related
Jan 12, 2013
1.) I don't have a wireless card in my PC, so I will be connecting wired to get WiFi via WAN and LAN ports, right? I have a Windows 7 32-bit desktop PC. We are working with a DSL modem residential line without phone line using a coaxial cable, and Ethernet cable from modem into the PC. provide step by step walk through instructions by connecting this D-link router to my modem and WiFi, and for me to use the WPA2 security?
2.) I have an iPhone 4 with Verizon. If I want to use my iPhone to get WiFi from the router, and turn off the Internet, and use WiFi only on my phone, how would this work?
View 14 Replies
View Related
Feb 17, 2012
I have two separate wired networks. Network 1 has a wireless router (an adsl modem). Router of the Network 2 is not wireless. Can I replace router of network 2 with DIR-600 to make a wireless connection between these two network segments ?
View 5 Replies
View Related
Apr 12, 2011
I should start by saying I am no novice when it comes to networks but this router has been nothing but a issue since day one.
*The Setup - 2 wired PCS, 2 Wired Macs, 1 Wireless Iphone, 1 Wireless Ipad.
WPA2 Only / AES key, Channel 6, G/N only, Hidden SSID.
*The Problem - 95% of the time the wireless and wired is running fine. However, Sometimes randomly webpages on the computer will stop loading... but heres the kicker... other internet connected programs like Ventrilo, or torrents, or games will still be working and running from the net like there is no problem. When this happens the internet browsers on the macs and PCs will say page cannot be displayed instantly. Happens to all computers at the same time. After about 10min the webpages will load again. I have 16mbs internet and while this is happening my games and voice chat programs do not go up in ping at all.
I have turned off QoS since that made the most sence... but other then that I have no been able to figure it out. I even turned off wireless while it was happening and it still didnt fix it. A sure fire way to fix it is to restart the router.
I am 100% stumped. Do I just have a bad out of the box router? it is only 2 weeks old.
View 14 Replies
View Related
Feb 8, 2013
After 5 years of services my DIR-655 begun acting up yesterday; first of it begun by getting REALLY slow, it could take up to 25 seconds to login into the software and up to 30+ seconds just going from one menu to another, on some instances connection (wired) to the router was lost. This morning it started dropping all connections, wired or not; first my iphone then my WDTV, after that it's been pretty much random connections. On one given moment wired works but not wireless, then wireless works but not wired and sometimes I get both but for 3 or 4 minutes.I've reset the router to factory settings, plugged/unplugged, changed cables, network adapters on desktops and the problem persists.
DIR-655 A2
FW: 1.35
Connection: ADSL
View 2 Replies
View Related
Oct 4, 2011
I have problem connecting Samsung (series6) TV to DIR-600. TV wired connection does not work with DLINK DIR-600 150. Is there a work around ?
Config :
DIR 600 is working in access point mode
Check list : Cat-6 Patch Cord - works (brand new works fine with laptop)TV network port - works (works fine with aztech ADSL/Switch)
View 14 Replies
View Related
Apr 15, 2012
Upstairs I have my internet coming in with a Comcast modem/ router ( I will be bridging this b'cuz it sucks as a router). Also, I have my Dir 655 upstairs that I will use for wireless. and I have my dir615 downstairs and I want to use it as a basic switch/wired router. How do I set up my dir615 as a switch/wired router?
View 1 Replies
View Related
Mar 11, 2012
I noticed after setting up the router. My download speed has dropped.
View 3 Replies
View Related
Apr 3, 2012
Why there is low speed using D-Link in compare with LAN wired connection?
View 9 Replies
View Related