Forming Bridge Between Wireless And LAN For Internet Access?
Mar 10, 2013
Just a little bit of info on the setup I am TRYING to run:
1) Laptop connected to my router via wireless
2) Xbox 360 connected via ethernet port to Laptop
3) Forming bridge between wireless and LAN to give 2 access to internet whilst 1 being able to maintain access.
Foreword: I've tried using ICS before hand because it was a simple alternative, had problems with it and got IP address errors on 2. When it did work, worked exactly how I wanted/need it to. (Was very un-reliable )
Goal: Have constant wireless access to 1 and be able to turn off/ on 2 and have access to internet without any problems.
Problem: So I am able to bridge the two connections just fine and I maintain internet on both, but when I turn off 2 the wireless drops and will stay at " Identifying" for hours and will either A) completely drop and not connect or B) stalls at identifying.
The way I have been able to get wireless back on 1 is to delete the bridge I formed and un-bridge my wireless. At that point my wireless comes back instantly and there are no problems. The thing is I don't want to have to repeat the process every time I want to use 2. With ICS it was " Plug and Play" when it worked and that's my goal. To plug in the ethernet cord via LAN and to be able to use 2.
View 1 Replies
ADVERTISEMENT
Sep 23, 2011
I have a wireless OS X 10.7.1 Mac a Windows 7 laptop, also wireless and one Windows 7 desktop, also wireless but close enough to my wireless modem that it can be hard lined in. If I use the "bridging" option in the modem settings, which I assume requires I enter the Mac address all devices:1. do I need to include my network printer?2. can I still access the internet from all computers?3. if I can access the internet, do I need to do so with everything going thru one computer or can they all connect independently?
View 10 Replies
View Related
Feb 12, 2013
I' ve come across an weird ospf issue between my router connected via layer 2 service provider link, details as below.We have a base station router for satelite termination at service provider end connected via Layer 2 vlan link to a head end C3945, current interface for head end is a layer 2 vlan and layer 3 ip address lives under sub interface, config as below
-Head End router
-Cisco 33945
View 4 Replies
View Related
Jan 12, 2012
i am trying to set up a tunnel connection between twO 2800 routers A<->B
1) destination ip is-204.x.x.x-ROUTER A2) source ip is 166.x.x.22-ROUTER B The router B has the modem connected to GE0/1 whose interface ip is 166.x.x.22 The ip-forward-protocol nd is configured as below
ip route 204.x.x.x 255.255.255.255 166.x.x.21
Also tunnel 1 configuration,isakmp policy are configured properly when i run show crypto isakmp sa it shows MM_NO_STATE,i checked the preshared key on both ends and they are same.whenever i remove the ip address of the interface Ge0/0 and ip route i can ping the 166.x.x.21 which is the modem gateway.when i revert back the configuration to the above ,the ip 166.x.x.21 cannot be pinged,the dsl connection is live though.ways to fix this so that i can make this tunnel state to QM_IDLE?
View 1 Replies
View Related
Jan 1, 2013
We have a RV120W Wireless-N VPN Firewall and we want to configure the router in brigde mode (transparent). Because we have another Firewall, use for filtering and default gateway on the LAN. The ISP provide IP address by DHCP, so we must connect the internet connexion to the WAN interface. But How can we do for connected the RV120W to our firewall? The router mode on the RV120w allows-it to make this configuration?
View 1 Replies
View Related
Feb 19, 2012
I just purchased a WET200 wireless bridge. After trying a very long password for an enterprise certificate the bridge restarted and I have not been able to contact the device with the default 192.168.1.226 ip address. I have tried performing a reset even by holding the reset button in for a minute. The bridge will not ping either. I do have a power light and the wireless light flashes and the Ethernet port lights function when plugged into my laptop.
View 3 Replies
View Related
Apr 12, 2011
I have an ADSL2 connection at home served by a DLINK DSL-2760U modem+router . I also have a DIR-655 router.Is there any way I can use the 655 as a wireless repeater/access point/bridge to connect to the 2760U (reception issues between the floors)?
View 1 Replies
View Related
Oct 21, 2012
I wonder if I can join via the WAP 4410n Bridge and also work as Access-point at a time. The idea is that you can connect to a router that provides Internet service that makes access-point bridge and connect to another WAP 4410n which would be another single access point for wireless bridge.
View 1 Replies
View Related
Jul 14, 2011
We have 4 access points in my network i want configure 1 is ap mode another 3 is bridge mode Is it possible to configure in 4410 N ? if i configure bridge mode can i use single SSID&Securtiy key for all aps. how to i use these 4 access points
View 1 Replies
View Related
Apr 3, 2013
I am trying to build a bridge between two of my access points. Both the access points connected to the wireless controller. I have changed the AP mode to "Bridge" after changing the power to custom.
The access points have both rebooted - but never "joined" the controller again. I have checked on the following pdf.
[URL]
One thing I can see - if I run a ping to the last IP.. every now and again I get a single response then it drops again. Via the console on the access point I can see it's getting to the controller, getting its name then reading something that caught my eye
"
*Apr 4 11:41:24.451: %CAPWAP-3-ERRORLOG: Go join a capwap controller
*Apr 4 11:41:19.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 57.24.10.53 peer_port: 5246
[Code]......
View 9 Replies
View Related
Nov 21, 2011
I have a pair of Aironet 1310's I am needing to bridge. I have used the CLI to configure the BVI1 with the ip address and verified it. I then tried to access the GUI to configure the device via Internet Explorer and it would not provide access. I read that it had to be older versions of IE but my OS will not support older versions. I then downloaded Netsace Navigator 7.01 as indicated, but still did not get access.
Then I thought maybe if I can access the GUIvia the IPSU tool but I have Googled the Cisco IPSU and cannot find a downloadable link.
View 3 Replies
View Related
Feb 2, 2011
I want to make a bridge with 2 WAP4410N access points.But what is the totaly distance that the access point can make to have an good connection in an open area?
So example:one WAP4410N in a house (near a window) and the other in a house (near a window) and the 2 houses lie 200 meters of each other. Is this possible?
If it is not possible with this access points, what is then an option/possibility ?
View 1 Replies
View Related
Mar 5, 2013
I have two 1262N access points with 5Ghz antennas, and I have configured one of them as a root bridge and the other as a non-root bridge; both using the same ssid. I have enble both dott11Radio interfaces on each access point. The problem I am having is that they do not associate. I have not configured them for any encryption or security. I just want to make sure the connect before I add any other configuration. Is there anything else that I need to configure to make them associate.
View 1 Replies
View Related
Sep 27, 2011
I have a router that is capable of wireless N at 5.0GHz but can't run simultaneous with it's 2.4GHz band a/b/g (Cisco Linksys E2000), so I have a second router acting as gateway for my b/g devices (and a few wired only that are nearer to it). They are connected LAN port to LAN port with 50ft of cat6 and the DHCP server running on only one router. I know this is pretty standard for multiple access points, and it works very well. But I'm moving, and in the new house, the internet access will be on one floor with the wireless N router, and the other router will need to be in the basement on the opposite end of the house, and running networking cable through the floor and walls is just too much trouble. My question is, can I replace the previous wired method with a wireless N bridge attached to the LAN port of the router in the basement and have it function in the same way as it did when it was wired, with only the DHCP server running on the wireless N router, and all devices attached to either router able to see each other? I would assume so, but I would like to know from anyone who has experience with it before I go buying the bridge.
View 3 Replies
View Related
Sep 6, 2011
I have spent most of the weekend trying to get this router to act as a proper Access Point.
When it does work (Stay connected) speeds and latency are rotten. If I go back to Routing Mode this thing kicks butt, but I isolate all devices attached to a different subnet and trying to set up proper routes has proved imposable. Firmware 1.0.2 r 13
The online help stated to connect to the "internet interface" when in Bridge Mode DHCP Server Is not broadcasting to on the wireless or wired interfaces.
If I used the wired interface as the uplink I can broadcast the DHCP to any device on wired but again nothing to the Wireless. When I "Show Routing Table" I see two static routes pointing to the ATT router for the Wired/Wireless Interfaces.. 0.0.0.0 255.255.255.0 (my Gateway) Wired/Wireless (my Gateway) 255.255.255.0 0.0.0. Wired/Wireless
AP mode should only be working in Broadcast. By connecting the Wired Interfaces alone up to my switched network should not use the router at all. If you force all traffic to my router all traffic has to be inspected by the firewall You create a bottleneck my router interface is 10/100.
ATT 2 Wire Gateway/Router with pinholes. 10/100/1000 Non managed 24 port Switch Network. Server infrastructure serving DNS/DHCP.
I decided to buy this after reading it offered Bridge/Access Point mode instead of getting the WAP610 because I wanted to have the option to change to routing mode or AP mode. Since my ATT Uverse Router Wireless is “g” it takes forever to transfer files to and from my servers.
View 4 Replies
View Related
Dec 15, 2012
After updating the firmware of th EA6500 to Ver.1.1.28.146072 I have no longer access to the GUI options of Speed Test, Guest Access, Parental Controls, Media Prioritization and USB Storage. I have reset the router to factory default settings and still none of the items are showing on the web page the only options available are:Connectivity,Troubleshooting.Wireless.
View 5 Replies
View Related
Apr 9, 2012
I want to connect two buildings. Let's call them Building A (main) and Building B.
„A“ is the main building and provides a wired LAN to an AAA server (192.168.1.2) and the WAN gateway (192.168.1.1). There I placed a 1262N with the IP 192.168.1.3 connected to the wired LAN and configured it as Root-Bridge. Let's call it AP01.
„B“ is a pretty large building and has a wired LAN from one end to the other end.
So I placed two 1262N there, each at one end.
The first 1262N is configured as non-root Bridge (AP02) and connects to the Root Bridge (AP01). The IP address of AP02 is 192.168.1.4.
The second 1262N is configured as Access Point (AP03) and connects to the non-root Bridge (AP02) via the wired LAN. The IP adress of AP03 is 192.168.1.5
My Questions:
1. Do I need tell AP02 about the AAA Server in Building A or acts AP01 like a AAA Proxy for AP02 because of it Root Bridge functionality?
2. How Do I tell AP03 that it should use AP02 as a gateway to building A?
View 2 Replies
View Related
Mar 18, 2013
I have a Cisco 880 (supplied by my company and as such I have little access to the control panel). I have a Linksys (Cisco) E1200 to use as an access point. Cisco setup (love it!) but the simple setup gives the E1200 an ip range starting at 192.168.1.1 while the Cisco 880 range is 192.168.185.113. I need to have all connections in the same ip rage (192.168.185.xxx) for remote monitoring. What is the best way to accomplish this? Bridge mode (I don't need Guest Mode which I read is not possible in bridge mode)? Disable DHCP on the E1200?
View 1 Replies
View Related
Mar 29, 2007
I just got a WET54GS5 to use for game systems. i wa able to use the software in order to get the system online and working, but i am not able to access the wireless bridge though the web page. the username is blank and i put in the correct password, but it does not go through.
View 7 Replies
View Related
Mar 26, 2011
I'm trying to connect my Ipod to the internet for updates that i cant download directly with my laptop. I'm Using a Laptop (Vista) with a Built-in Wireless, and i only have internet access with a Telstra mobile internet USB.
I have created an Ad-Hoc network, but still can't get my ipod to connect to it. and i can't bridge my USB Internet connection (shows up under dialup) with my ad-hoc network (shows up under LAN/High Speed Internet). I have also changed the settings for ICS.
View 3 Replies
View Related
Mar 4, 2013
How do I connect to the EA6500 once it's in Bridge mode acting as a wireless access point? Checked the posts and some seem to be able to do this but, we cannot.
View 6 Replies
View Related
Sep 5, 2011
I have 12 wap4410n to enable wireless connection to a school building with 3 floor. I planned to configure one as a Access point. My doubt is in which AP mode i have to configure the rest as WDS Bridge or WDS Repeater other mode. In each access point i have Ethernet connection to the switch.
View 1 Replies
View Related
Oct 23, 2011
I have a spare computer being used as a DVR in my home theater. Running a CAT 5 cable from my main computer/router (a Linksys 610N) to the home theater computer is not an option. I am unsure if I need a wireless bridge (WET610N), a simultaneous USB wireless-N adapter, or a wireless access point (WAP610N).
View 5 Replies
View Related
Jul 11, 2012
Im trying to bridge my zyxel eq660r-f1 dsl modem so that i can resolve the nat issue im having in my home network. Only problem is that everytime I bridge the modem and hook my E4200 up, I cannot connect to the internet. If i connect my laptop directly to the modem, I do get internet but not through the router itself.
View 8 Replies
View Related
Dec 6, 2011
I recently changed my internet connection to DSL from Cable, so now I'm using PPPoE type of connection.
Right now my router is configured as Automatic DHCP with the modem doing the PPPoE connection. All is fine and well.
Since I own a PS3, and Nat Type 3 conection is really bad for my online gaming, I would like to bridge my modem and connect to the internet through my router. That way I can properly forward my ports, use QoS and effectively get a better connection on the PS3.
I was able to successfully bridge the modem, but the PPPoE config on the router isn't able to connect to the internet.
Modem and router have been reinitialized after the configurations were changed. I do have the username and passwords, and they were properly put on the router.
View 1 Replies
View Related
Feb 28, 2011
how can i configure my wireless access point to receive internet connection from Wireless tours
View 1 Replies
View Related
May 8, 2011
I like the ease and price of the 655 as well as the range and speed. I was wondering if you can use them as a bridge to connect another building or just add a second as an access point? It does not seem straightforward from the control panel.
View 14 Replies
View Related
May 13, 2012
I've got a Cisco 1841 with 2 FastEthernet ports here. My Cisco isn't great, and I've been given a problem I don't seem to be able to crack.Essentially, I have one network with two sides. I've connected these to fe0/0 and fe0/1 on the router, and put them interfaces into a bridge group which as far as I can tell, essentially makes the router a 2 port switch...I know this won't make a lot of sense from a normal network point of view, but what we need to do is allow all traffic from fe0/0 to fe0/1, but not allow any traffic in the reverse direction. The traffic allowed to flow from fe0/0 to fe0/1 must include broadcast traffic (infact that is the most important traffic, its how the silly theatre application works). None of the traffic is IP addressed.... ie, each of the devices on the network assign themselves an IP address, and then throw broadcast traffic out on to the "dedicated physical network" that exists between them for communication[CODE]
View 2 Replies
View Related
Aug 23, 2011
My apartment already has internet provided to all of the rooms, but I'm trying to set up my router as a wireless access point. I tried disabling DHCP on the router, but then I wasn't able to get any internet access at all. Does this device not support bridge mode?
View 5 Replies
View Related
Mar 28, 2011
According to the information on the bottom of the WAP54G setup screen it can connect to the WRT54G without another WAP54G. What I want to do is use the WAP54G as a bridge to connect my DVD player with an Ethernet connection to the internet via the WRT54G. Both units have the latest firmware updates. When I set it up as I believe it should be the WAP54G has all the lights on but the DVD player cannot connect to the internet.
View 5 Replies
View Related
Dec 4, 2011
How do I connect three or more WAP54G's in bridge.
View 3 Replies
View Related
Dec 20, 2012
Just bought a new router and repeater for a wifi hotspot i am currently running.. I thought i was havng problems with the repeater after i change from router to a server, (and i'm now using a router in bridge mode) so the server is managing all the dhcp.. etc, Hence, the router is Running as an access point. The server which is a Hotspot Server does the rest. For some reason, repeaters, do connect to the access point apparently, but when connecting the client to the repeater (instead of access point) I can't get internet access. although i do get access to the repeater setup.and access point setup too.. or if that is the fact that repeaters must be connected to a router, not access point? should I use it as a WDS? or AP-wds? I have a Cisco Lynksys e1200 router (which i'm using as access point) and an Encore ENXWI-1AN45 3 in one range extender?
View 2 Replies
View Related
Dec 26, 2012
Is it possile make a bridge with my WAG54G2 and another Access Point ?
View 1 Replies
View Related
