How To Add 3 More PC To LAN Network Which Are 80 To 90 Meters Far
Sep 2, 2012
i have lan network it contains
1.1 internet router 1 Mbps(connected to switch)
1. 24 port switch 10/100 Ethernet
3.23 desktop computers
4. cat 6e Ethernet cable
everything is working fine internet is accessed by all pcs now i have to add 3 more computers to this same lan network to share internet & file sharing. so how can i do the lan setup ? 3 pcs are about 80- 90 meter far in same room this my 2 solution which would work without effecting the speed of internet and best ?
solution 1.24 port 10/100 Ethernet switch connected to 2nd switch 10/ 100 ethernet and add 3 pc to 2 nd switch via 3 cat 6e Ethernet cable which is 80-90 meter far for 3 desktop pc
solution 2: connected 80 -90 meter long cat 6e Ethernet cable from switch 1 directly to 16 port 10/100 ethernet 2 nd switch and from 2nd switch i took 3 cat 6e ethernet cable to 3 pc which are 20 meter far
I have a new site needing PoE for their VoIP system as well as the usual LAN config.I haven't used Cisco PoE switches for a good couple of years now and was wondering what you think of the 2960-48PST-S?
I will probably need PoE up to around 50 Meters and will be using PoE on most of the 48 ports over CAT5e 100Mbps with 1Gbps upload is fine so these switches do seem to tick all the boxes but I’m not sure if there are better options?
My laptop connects and has excellent strength throughout my whole home but my internet slows down when i move only three meters away from my modem. I have been sent a new modem, changed wireless channels and troubleshooted with my network provider but still no luck.
If I try to connect to my internet wirelessly and my laptop has more than 2 meters distance approximately from my router then for some reason it doesn't connect.The laptop can spot my network at that distance and i can connect without problems from any other device such as my mobile phone or my mother's laptop, so I'm pretty sure that I'm not out of reach.Occasionaly it connects but this appens very rarely (in fact it happened twice so far), disconnects shortly after (after about 5 min) and the internet speed during that time is rediculously slow
Just installed a new WAG120N for a customer.All works fine except when I go to her sleep out, not more than 6 meters away - no connectivity through wireless, so bad that it doesn't even see it - this is with two separate laptops.The walls are nothing special - wood outside, wool fiber insulation & gib board inside.Roof standard corrugated iron.
I have a relatively simple question. I would like to create a private network within a larger network, the private network having several clients. I would ideally like the router to appear as the only device on the larger network and all data to be sorted by the router to the clients in the private network.
Will the Netgear FVS318G be able to do that? It seems to have the necessary NAT options.
I have 4 computers (3 laptops, 1 desktop) in a shared office. We get internet access using their wireless network. All works fine. However, I need to share a printer amongst all of the computers. The printer is LAN enabled and I would normally just put all the PCs on a hub, together with the printer and share it that way. BUT my question is can we access the internet using the wireless network and the printer using a separate wired network at the same time?
This past weekend I went out of town and took my Windows 7 laptop with me -- since I returned home, it has been unable to connect to my wireless network. Other devices in my home connect to the network just fine, and the problem laptop has always been fine until now. My network card is an Atheros AR9285, and I'm attempting to connect to a Medialink router with WPA password protection and AES encryption.My wireless network icon in the task bar has a yellow sign with an exclamation point in it. It says "No Internet access."
I use my desktop for streaming media throughout the house. I found it was causing lag for gaming most likely because it was taking up all the bandwidth for the router. We had a 2nd router laying around as well as a 2nd wireless adapter so we set up a 2nd network that was not connected to the internet for strictly media streaming.I attempted to change the network settings so the internet connection appeared as a public network so that streaming of media was hopefully diverted to the non internet wireless adapter.I want a faster way of transferring large video files from my laptop to my desktop. I recently bought a crossover cable to do this through direct connection.Both use the same user name and password as well as run the same win 7 pro however the desktop is the 64 bit version. I set up both ipv4 with the same addresses.When it has worked I am only getting a connection speed of just over 10mb and once I connect the crossover cable between the computers it knocks out my internet connection on the wireless card.
I seem to be struggling to connect more than 4 cameras to my (ISP-supplied) modem/router by Netgear CGD24N via WPS. I'm on my 5th camera now (already have 3x 930L and 1x 942L) but the newest 942L just won't connect to the network at the moment and there's definitely no faults here as I swapped cameras today at the local retailer (and got an A3 942L!).I've even tried connecting the camera to my wireless extender (Netgear WN3000RP) but no luck there.
So far it has only worked twice for short periods of time (enough for me to configure the cameras) but since then I can't actually get it working. I've got a couple of spare wireless routers lying around too and should be receiving a DIR-600 soon (from the Netgear promotion in Australia) which could be useful?
I connected my camera to my router with a network cable. It is a DCS-2121, H/W Ver A2, with firmware 1.04_FR.It received an IP address and I could access it fine with a web browser.Then I configured it to work wireless.I disconnected the cable but the camera wasn't accessible.Since I couldn't find it I re-attached it with a network cable, but this didn't work.So I pressed the Reset button to start over again.However, now I cannot get it to work anymore. When I plug in the camera and have it connected with a network cable to the router the status light remains RED.When I plug it in without a network cable the status led remains RED.When I connect it with a network cable to a computer directly, the status led remains RED.I've tried changing the network settings of my router to use 192.168.0.x as range, but it makes no difference. In all cases the status indicator remains RED.
I'm experimenting/attempting to use a laptop as a network tap between my (DSL) modem and a wrt54gs by creating a bridge with two NICs in the laptop. My problem is I can't seem to get connectivity on the user end of the router. I can't ping the bridge from an end computer...
DHCP is disabled in the router, but even when manually configuring the IP address on an end computer and using the bridge as a default gateway I can't ping out.
Am I completely misunderstanding the purpose of a NIC bridge?
I want to setup a DC++ HUB for sharing data within the university local network. We have addresses of the form 172.31.*.*. These addressed are accessible within the university bu non routable outside on the internet. My plan is to setup a local HUB for DC++ for sharing data within the university intranet. So even if internet is unavailable data can be exchanged through LAN. This HUB must not be accessable outsied the university network.how should I do this all..implementing network sharing other than DC++. My basic idea is that everybody can share their data and the data is searchable from one common interface( Web interface is better option, if possible). And data featching should prefferably be from many hosts, using multiple connections so that speed can be improved..
I have a crappy router/modem from comcast with two windows machines and a linux web server connected. I also have another router, a Linksys WRT54G with DDWRT firmware with WAN connected to the modem/router. The linux web server has a static IP, configured with /etc/network/interfaces The network goes down randomly. Disconnecting and rebooting the linux web server usually fixes it. It's possible that the WRT54G could be at fault as well.The problem is that I just don't have any information on what is happening on the network. (Well even if I had the information, I'm not sure I would know what to do with it) I installed wireshark, I figure I should just leave it running until the network goes down, then I can go through the packets and see if I see anything weird?
i can search for networks. As you can tell i am currently on the internet on my laptop. I can search for the current network i am on through my adapter. I then connect to it. It says im connected to a unidentified network. It will not let me search the internet or anything else.
I have a home network running all Mac computers (though can run Windows VM if necessary) and a pair of USB printers. The wireless router and cable modem are in one room, but the printers are in another. I'd like to find the most practical way to add the printers to the local wireless network without sharing them from a computer. I've tried that for a while, but don't want to leave a laptop connected 24/7 just to enable wireless printing (rather defeats the purpose of a portable computer). I don't have any wired network lines in the home, and am not excited by the idea of running any cables.
My company have a Cisco PIX 525 firewall which is cater for NOC internal data network and also voice network, the subnet for data network is 192.168.2.0/24 and the subnet for voice network is 172.16.2.0/24. someday this NOC firewall was faulty. I was migrated the data network from this NOC firewall to the other temporary firewall just at the moment. And the voice network i migrated it from where it orginal at NOC firewall to a VOIP system which actually having a connection with my temporary firewall(This temporary FW only to take the traffic of data network). After the migration of data network from old firewall to temporary firewall and also the migration of voice network from old firewall to PABX system. The subnet for data network remain the same as 192.168.2.0/24, but the subnet of voice network i edit from 172.16.2.0/24 to 192.168. 3.0/24.Now when i want to use one Cisco router 2600 to replace this temporary firewall then facing problem at the voice network....The data network after migrated from temporary firewall to new 2600 is ok, users can browsing. But when i trying to at the same time when the data network been migrated , it will affect the voice network which still located at PABX. ..user cannot make call...I was thinking reason because this voice network which currently in 192.168.3.0/24 is tight to somewhere on the 192.168.x.x at the old firewall internetwork. So, when i migrated the data network over to new router, it will also cause the failure of voice even thought after i migrated the voice system to new router.So when i do the disaster recovery back to the temporary firewall for both data and voice. The voice is resuming to normal.
Camera set up with the Beta Mac wizard connected via ethernet on Airport base. Wireless security WPA2 Personal. Using DHCP. AirPort Utility 5.5.2, OSX 10.6.6.I can see the cam with the myDlink Lite iPhone (4) App when I am in my house with my wireless network. When I am out, away from my network, the App can't connect to the cam, tells me to check my network settings. I did the wps way and added the cam in the airport base utility *Access Control* tab but still doesn't work. Checked in the cam web page settings, can't figure out what the Pre-Shared Key is and where I get it/set it up in the airport utility...
I'm trying to configure my BRI interface in "network protocol-emulate network" and "layer1-emulate network" but i don't have this second command.Is someone have allready to that with this type of interface ?I've to configure this because the ISDN line of my telco is in user mode only.
What's the least expensive way to enable Guest Network authentication in a network with WLC 4404 controllers and no WCS? Management would like guests to register with a valid email address and enter a 'password du jour' to keep unauthenticated users from chewing up bandwith with automatic connections.
Having an issue with a Cisco Linksys E1500 on a home network. The device has a feature to provide a guest wireless network but the guest network can't get to the internet. A wired connection is fine, as is the normal wireless network but not the guest. The cheesy thing is, that it doesn't list an option for what type of wireless security protocol you want on the guest network. I'm assuming that it uses the same security protocol that the normal wireless network uses, but who knowsEspecially weird is that it asks you what password you want on the guest network but then the guest network show to be insecure when you try to connectthought maybe it was something funky with some of my configurations so I went ahead and factory defaulted it and just set it up with an insecure network for both the normal and guest networks. This didn't solve it. The guest network still couldn't get to the internet. In fact, the guest network can't even ping the router.
I currently have a BT Home Hub 3 router and an Ubiquiti Power AP N.What I am trying to do is use the Ubiquiti access point as the main device for all connections in my house (ethernet and wireless) so that I can use the QoS settings etc. I basically want the Home Hub router to play as little role as possible in the network except for providing the ADSL internet connection.I know I need to enable DHCP on the access point but everytime I do so the devices connected to the access point lose internet connection.(BTW I have an ethernet cable connected from one of the routers LAN ports into the access point's WAN port)
I'm looking to connect my 50+ drops I have in my home based business. I transfer large files 5+gigs on a regular basis between the machines. I currently just have some cheap Netgear 8port, gigabyte switch's but when transferring files I max out around 12-15mb/sec. This takes WAY too long to transfer files.
I need a network switch so I can get my speeds up to 60+mb/sec at least. (my seconds job office has this ability)
What would I need to get this kind of speed? All my cabling is CAT6, with CAT6 ends. Would I need a managed switch to get this kind of speed?
I was looking at a couple switches. Cisco Sg 100-24 24-PORT Gigabit Switch $374 or Cheaper option Netgear Prosafe GS724T-300NAS 24 Port Gigabit Smart Switch W/ Rack Mount Kit $199
Or is there something else I could go with in this price range?
i'm connected to the internet through a shared internet connection through a switch,and also have 3 computers connected to the same switch,what i want to setup a local network between the 3 computers but separated from the internet network?
I'm using a coaxial networking system and would like to electronically identify each section of coax in my network with a mac id for tracking purposes. Is there any way to do this without taking much space? Is there a microchip that I can install,preferably something that can withstand extreme environments?
I've been having some issues with my network connectivity for a while now, and I haven't been able to figure out what the problem is. I run a wired connection to an Ethernet port in the wall of my university dorm. I have verified that it is not a global network issue or an ISP issue; this problem only happens on my PC.My network connection drops/disconnects randomly throughout the day. When I say disconnect/drop, I mean that all attempts to ping or access the internet fail. A few minutes pass before the Network and Sharing center task tray icon shows a warning sign saying that my computer could not connect to the internet.This is temporarily fixed by doing an ipconfig /release and ipconfig /renew, but I have to execute these two commands about 2-3 times a day on average.
There is no exact interval between the disconnects, nor does it happen when I am running particular programs. The disconnect happens regardless of what I am doing at the moment (gaming, browsing the internet, leaving the computer idle).A month back, I installed some Windows Updates and suddenly my internet connection was almost completely broken. I was experiencing the same issue, but much more frequently. My internet would die within 10 seconds of executing any download, but Windows wouldn't recognize that something was wrong. At first I thought the ZoneAlarm, Avast!, or the SafeConnect (as required by my university) services were causing trouble but uninstalling/disabling these services did not fix the problem.I also tried reverting to my default ethernet drivers, which did nothing. I uninstalled and reinstalled multiple versions of my drivers to no avail.However, the internet worked just fine in Safe Mode with Networking, so I cross-referenced the processes/services running in Safe Mode w/ Networking against my normal startup, guessing something else was at play.After some poking around, I discovered that disabling the Server and Browser services permanently fixed the issue of instant connection death. But the initial problem I described still remains;random, less frequent internet connection drops.
I have a windows 7 desktop with an SSD and regular mechanical hard drive where I keep my data. I also have a laptop with a small SSD as well. I wanted to keep the laptop free of non-critical data so I decided to setup a file share between my desktop (Windows 7 home prem) and my laptop (Windows 7 pro). I was able share the files and navigate to my desktop through my laptop. I successfully mapped the folder as a network drive and all was well. Then I rebooted and I was disconnected from it, it remembered that it was there but I needed to manually connect to it and I needed to provide my login credentials. There is no password just a username.
What is causing this and is there a way to get around this? Also is there a way to set a timeout because if my desktop is not on and I want to use my laptop, the boot times are much longer compared to when I don't have the mapped network drive on my laptop at all.
In the bottom floor there are three computers, an iMac computer that receives an average wireless Internet signal, desktop computer and a laptop.I want to take care of the desktop computer and buy a network card, the next card:TP-Link TL-WN951NNow it has three antennas, each of its reception range is 2 dbiI should buy three of the 10 dbi antennas and connect them to the network card?It will give a good solution strong wireless signal and good speed?
I have a Dell Optiplex running XP wired to a Netgear router. My laptop is a Dell Inspiron 1501 running Windows 7. When I got the new router everything programed easily and I could retrieve files from my desktop and print remotely. Sometimes I would have to "refresh" before the laptop would detect the desktop but now it will not detect the desktop or the printer. I suspect that a Microsoft Update did this but just guessing. I went back and deleted the updates that downloaded around the time that this stopped working. I have tried every thing that I can think of to get it back working but can not get it fixed.
