The internet was working on and off for a few days but yesterday and now today it has not been working. The router I have connected is fine and the laptops and xbox that I am trying to get internet on connect to the router but will not connect to the internet. The modem is what I believe the problem is however,I am not that great in the networking department. I have a Westell 6100 it is Verizon DSL.
View 1 Replies
my router and modem is working but no internet acess ive try rebooting my router but still noting change...dont know what to do...h
Microsoft Windows [Version 6.1.7601]
Copyright (c) 2009 Microsoft Corporation. All rights reserved.
C:Userslito lapid>ipconfig/all
[Code]......
I am using a broadband internet of a provider named BSNL,through a simple modem. Recently I got a Beetel 450BX1 ADSL2 + Router and want to use the wireless capability of the laptop so that I don't have to be glued to my table. The OS I'm using is Windows 7 Ultimate (32 bit) on an HP Compaq 6515b.I configured the modem by following the instructions in the following link url...I believe that's a straightforward method for configuring a router, and that accomplishing this is very simple.I followed the steps, only changed the username and password to that given by BSNL.Then, finally I unplugged the LAN cable and clicked on Connect to <connection name>, punched in the serial key. But it does not connect and says "Windows was unable to connect". Even after using Windows Network Troubleshooter the problem is not solved.
View 4 Replies View RelatedSometimes my wifi signal will randomly drop and I cannot browse the Internet. The network still appears on my computer and I can connect to it, however Internet pages will not load. This lasts for hours, sometimes days. If I unplug the modem from the router and connect directly to the modem via Ethernet, everything works fine! I have tried unplugging everything for 1 minute then plugging it back in and it does nothing.
View 2 Replies View RelatedBasically, my internet's been fine until about a week ago. I'm currently using the Aztech DSL1000EW router/modem which has been working great up to now. My problem is this: after about 5-30 minutes (time fluctuates, annoying because after 15 minutes of continuous usage you think the problem's solved!) all webpages suddenly become 'unavailable'. I've disabled proxies under LAN settings, tried flushing DNS, resetting winsock with the netsh commands but to no avail. To get the internet to work again, I can just go to my router page, click disconnect and reconnect and it'll work for another 5-30 minutes.
View 8 Replies View Relatedi have a DSL-2730U WIRELESS N 150 ADSL2+ 4-PORT ROUTER which i have been using for the past 2 months.It was working fine,but since the last 5 days when i plug the lan wire into the PC port, nothing happens...it doesn't get recognized..the green light in the port is always glowing..i've tried another cable..same problem...i've tried it on another laptop..it works FINE....
View 1 Replies View RelatedI bought a smartphone a couple of months ago, it connects to the web with 3G with no problems. However I can't get it to connect with my modem. I have ticked the phone settings to look for available WiFi and it picks up the name of my modem but says it's disabled, secured with WPA/WPA2 PSK. The phone can't connect to my modem
View 8 Replies View RelatedI plugged in the USB from the Modem to my desktop and my desktop doesn't see the modem, I don't want the router to my desktop because it is interferring with my magicjack
View 3 Replies View RelatedI have to separate internet providers and two different modems (one brand new!) - they both appear to be working fine but I can't get any internet coverage - neither on my macbook air, Mac nor my HP netbook. All say ethernet cable unplugges. I have been on tech support with both providers all morning, and now with a tech guy in the house for the last 2 hours and all indications are that the modems work
View 1 Replies View RelatedI don't think it's my PC, because I tried using the Ethernet cord on my laptop, and got the same error "limited or no connectivity..." When I try to troubleshoot on my PC, it says the modem is fine. All the lights are green on the modem. I did notice that I have an IP address, but no Gateway Address. Also, I'm sending few packets, but receiving even fewer.Is it safe to say that this is a modem issue? Or something else? Is there anything that can be done? -resetting the modem did not work.
View 14 Replies View RelatedI have a Netgear CVD31T modem delivered by my internet provider. I can't change any settings on the modem. My connection speed is 30 gb up and 5 GB down.Until now I used a Linksys WRT54GV ver. 2 router to share my connection between my computers and NAS server and it worked ok. In speed tests I normally get approx 25 - 28 GB speed. To optain more speed on my LAN I want to buy a GB router. And here started my problems. First I tried a D-link DIR655, then a Netgear WNDR3700 and latest a Linksys E3000. I all 3 occations my WAN speed droped drasticaly down to between 3 - 5 GB speed, at under a ping test I have a loss of between 10 - 30 % and time on approx 50 ms.If I connect my PC directly to the modem or re-connect my old router it works perfect. I have tried to replace cables etc. etc.
View 5 Replies View RelatedI need configuring the dsl-320t modem connected to the dir-600 router. Already tried some configuration, with dhcp enabled and disabled, tried to assign a static ip to the router and tried to put the modem in bridge mode, but fail miserably .Now I've resetted both devices, if I connect with the ethernet cable my pc and one of the four lan connectors on the router, and then use another ethernet cable to connect the modem port with one of the other three free router port, I can connect to internet. Any other configuration i tried has not worked.
View 9 Replies View RelatedI have a Comcast Motorola Surfboard rental modem. It works fine, great speeds etc etc. It has no router or bridge support.
I use this modem to connect to the web on my ps3 and PC. What I have been doing is simply unplugging the ethernet cord from one device, and putting it in the other device to switch. But of course things can't be simple...
Every time I switch devices, the modem tries to reconnect and does a cycle where every time it only reaches the "Send" light. So I have to power cycle my modem and wait about a half hour before my connection resumes...
I read something about PPPoE, but Comcast doesn't even use it so that won't work.
The modem Time Warner gave me several years ago was dying, I took it in, they gave me a Cisco modem, I plugged it into the computer, works fine, so then I plugged it into my airlink 101 wireless router, the computer recognizes the router but says there is no internet access, i.e. the modem and router are not communicating. Why would change of modem cause lack of communication with the router, is there something different about modems now compared with roughly 5 years ago? And what can i do to fix it so i can have wireless access again? If it matters, I have no protection on my wireless (because I never figured out how).
View 1 Replies View RelatedI have an HP Pavilion wireless laptop with windows vista and a gateway desktop, windows XP Home edition and every thing worked ok untill I got a virus on my desktop Since then I've formated the hard disks and reloaded the opering systems, but I don't know how to get the laptop working wirelessly without taking the motorola modem and connecting it directly to the laptop, I have a D-Link DIR-615 router.
View 4 Replies View RelatedI have a briteport 8012v1 modem and a linksys WRT54g router. I reset the router because I didn't have the password to get in and haven't been able to get the connection back since. When I'm connected directly to the modem, I'm sending but not receiving packets. I'm unable to ping the modem ip, or yahoo.com. I've tried manually configuring and using DHCP. I also cannot access the modem's configuration page. (After i initially reset the router, when I tried to access the router's configuration page and was directed to the modem configuration page). When I'm plugged in to the router, I am able to get to the router config page - but still no internet connection. The modem does not have a hard reset (the reset button only resets the login name/password). I've spoken with two people at my ISP who told me different things - one that I couldn't use PPPoe and one told me I should be using it. When I spoke with them this afternoon, I was told that he tried to ping my connection and he could not. They're going to have someone call me sometime tomorrow, but this is the internet connection in a busy office and we need to be up and running when business starts tomorrow.
View 1 Replies View RelatedRegion : Others
Model : TL-MR3420
Hardware Version : V2
Firmware Version :
ISP : YU KENYA
most service providers in our country dont have 3G or 4G support,but all the same i bought an MR3420 router in the hopes that since my modem is listed,it would still connect even if on an EDGE/2G network like YU-Kenya.But this is not the case,the router does not recognize the modem i.e it says the modem is unplugged but when i look at the logs,it indicated it detected the modem but LTE was set to zero. providing a modem bin file for compatibility under EDGE/2G connection otherwise my router will be of no use to me.
i have Linksys WAG320N and Draytek Vigor 2850. My main router is Vigor, wchich support 2 WANs. First WAN is my VDSL connection (plug direct into Vigor) and second WAN i want ADSL connection. Can I work with WAG320N only as ADSL modem?
View 1 Replies View RelatedRegion : India
Model : TL-MR3420
Hardware Version : V2
Firmware Version : Problem persists on all three firmware
ISP : BSNL india on EVDO
Today i purchased brand new Tp-Link MR-3420 3G/4G router for my BSNL EVDO modem..as this product is shown to support ZTE AC8700 modem...but it doesnt seem to work.. I put the right dial-up number,user name and password that i use when i connect modem to laptop and left APN field blank...The modem gets identified by the router but it just don't connect to internet,it just keeps saying "connecting.....". Also the signal strength is shown 0%... If your modem is really supporting ZTE AC8700 modem why its not working?
Region : India
Model : TL-MR3220
Hardware Version : V2
Firmware Version : 3.14.2 Build 120822 Rel.57775n
ISP : BSNL EVDO
my BSNL evdo ZTE AC8700 modem is not working with TL-MR3220 V2. The modem is being detected in the router and i have set the Dialing number, username, password. [code]
Region : India
Model : TL-MR3220
Hardware Version : Not Clear
Firmware Version : TL-MR3220_v_2_120822
ISP : MTS
My Hardware version is v2.Just now I bought this router. When I am trying to configure it with default firmware is not identifying the modem itself. So Afyter facing this problem, I updated my Router firmware(TL-MR3220_v_2_120822) and retry the process. But this time, It identified the modem for few seconds, then its changes its trying to connecting, after that its change it state to unplugged. It is doing these steps repeatably. Identifying >> Identified >> (connecting) >> Unplugged. [code]
my new netcore nw705p wireless router dns is not respondin
View 1 Replies View RelatedI am trying to setup a Dynalink Wireless 4 port modem and Network Connection is showing Local Area Connection Network Cable Unplugged,Firewalled, Broadcom Netlink (TM) Ethernet even though the LED light on the cable is flashing, indicating the cable is probably working. I am operating Windows XP Version 2002.
View 8 Replies View RelatedI have a Linksys WRT54GS, version 6 with Mac OS X (version 10.6.8) hooked up to a Scientific Atlantic cable modem, with RCN as the ISP.
Recently, RCN had some network issues, and so I had to power down and reset my modem. The modem is working fine now -- no problems at all when the Mac is connected direclty to the modem.
The router's network is OK in that I can connect the Mac wirelessly to the network, but I can't connect to the internet through the router (through neither the wireless or wired connection).
I have downloaded the latest firmware update for the router, following the Linksys site instructions.
I did call Linksys tech support on the advice of RCN, and they said that the router does appear to be working (power, WLAN, and Internet lights are on), but they would be charging me nearly the cost of a new router to fix the problem.
I am trying to figure out whats wrong with my parents apple airport router. Its connected into an Arris TM402P/110 cable modem. It randomly stops working, the network is there and shows up fine but you cant connect to it. It might work for a day or 2 and then just stops. I am trying to figure out if there is a configuration issue or the airport hardware is just failing. I am not sure where to start troubleshooting. The event log for the modem isnt much help, the following message shows up occasionally:
No Ranging Response received - T3 time-out
Whats interesting is my mom plugged her desktop right into the cable modem and then after plugging it back into the airport the wireless was working again. Is it possible there is a DHCP issue? If the hardware is failing what would be a good replacement for the airport?
Wireless Router - DI-514,Modem - Westell 6100, Every time I refresh the 'View available Network settings' My Connection name pops up with other connections but then disappears after I refresh again and others as well disappear, but some stay. Right now I'm using the the wire the blue wire that connects me to the internet.
View 3 Replies View RelatedI have a new Linksys E2100 that was working well with an old Verizon modem. Then recently that modem gave up the ghost and I was issued another one (Westel Model 6100G). I have no problems with internet connectivity when connecting directly from my harddrive to the Verizon modem. I am also not having trouble connecting to the Linksys routher as I am able to see my wireless connection with no problem. However, when I try to set up the connnection with the E2100 in the loop (yes, it's connected correctly) I no longer have internet access.I tried de-installing and re-installing the Linksys software (thinking maybe there was some new configuration that would be auto-detected with a new set-up), but this didn't work. I suspect that if the problem is with my Linksys router and not with my Verizon modem that there might be something that could be done to reconfigure something manually but I do not know enough about connections and wireless systems to trust myself not to mess something up.
View 1 Replies View RelatedI have a new Linksys E2100 that was working well with an old Verizon modem. Then recently that modem gave up the ghost and I was issued another one (Westel Model 6100G). I have no problems with internet connectivity when connecting directly from my harddrive to the Verizon modem. I am also not having trouble connecting to the Linksys routher as I am able to see my wireless connection with no problem. However, when I try to set up the connnection with the E2100 in the loop (yes, it's connected correctly) I no longer have internet access.
I tried de-installing and re-installing the Linksys software (thinking maybe there was some new configuration that would be auto-detected with a new set-up), but this didn't work. I suspect that if the problem is with my Linksys router and not with my Verizon modem that there might be something that could be done to reconfigure something manually but I do not know enough about connections and wireless systems to trust myself not to mess something up.
At this point I'm assuming it's a Linksys issue since I know that my Verizon modem can connect me to the internet, so works properly. Is there some known incompatibility with this Linksys model and the Westell 6100G modem?
I am at my wits end.Comcast just changed my old RCA cable modem for an Arris Telephony modem.(I had Comcast phone service added)The tech that did the install said the wireless G network was all up and running. (My 3 other computers and printer) Well lo and behold the network does not work at all. I only get internet through my wired computer and cannot access my router through 192.168.1.1 anymore.I tried powering down the router and modem by holding the reset for 30 seconds and unplugging them.
View 9 Replies View RelatedI hooked up with a Linksys WRT110 wireless router to a Zoom modem and my DSL on my desktop and laptop are both working fine. My problem is my phone lines quit working. I plugged a phone into the box outside and I had a dial tone. When you try to call my house it just keeps ringing.
View 1 Replies View RelatedI inherited a BEFCMU10 v.3 cable modem from my boss who switched to FiOS and I would like to use this with my Comcast connection.All I received from him is the cable modem and power adapter, what do I need to install and get this cable modem working? My router is WRT-54G.
View 2 Replies View RelatedI am connected to my network wirelessly and I have Internet acces (according to the symbol at the bottom right) bu the Internet doesn't work. At the moment it keeps fluctuating between giving me interne and not I am using Skype to tell me if I have Internet ( when it's green I do when it's grey I don't) I have tried many things on forums like obtaining ip automatically or obtaining a fixed ip. I've tried renewing the ip and all this doesnt work.
View 4 Replies View Relatedwhen i try to log on to google chrom...it states not connect to the network...at thr bottom of the computer it say noy connected connection avaiable
View 1 Replies View Related
