I'm thinking about buying a WAG54GP2 router. However, my ISP provides a modem which has uses RJ-45 lan cable. Is it possible to configure WAG54GP2 to use one of the lan ports as WAN? Is it possbile to change the mac address of that port?
View 1 Repliesdo WAG54GP2 routers have wds support? if they support, how can i configure?
View 1 Replies View Relatedi am signed up for an IPTV service. my service provider set up their own hardware including a reciever and a wireless modem. but their wireless modem has weak signal and i cannot connect to it using my computer in the other room. so i wanted to set up my WAG54GP2 modem to use with IPTV service. but i couldn't. i have followed the instructions described there:
[URL] (support page for some other IPTV provider, i guess)
so, i have checked the configuration details of the other modem which is provided by the IPTV company and found out that encapsulation mode is selected as "DHCP" instead of "Bridge mode only". But my linksys modem does not have an option named "DHCP". so, does it mean that it is impossible to use IPTV with my WAG54GP2 modem?
I bought a WRT54GP2 independently of my ISP/VOIP provider so I could have an all-in-one router. As my provider would not provision the VOIP side I disabled provisioning and set up the voice settings myself and it works perfectly.I was reviewing the VOICE settings side and under the SYSTEM tab there were settings for Administrator Password and User Password. Researching on the Net it seems these should be set to strong passwords which I did but then found trouble moving from the main part of the router configuration to the VOICE tab as I would get a message about a non-admin account not being able to administer the voice side. Via clearing the cache on my browser and restarting the router/browser I managed to get back into the VOICE config tab and immediately removed those two passwords. Seeing the settings under the SYSTEM tab it looked to me that the router was open on the WAN side on port 1880 so I disabled the web server and web server admin options thinking these were only related to the WAN side not the LAN side.
I now find out that I can no longer access the VOICE tab as the router immediately disconnects from the browser.I've tried contacting my ISP/VOIP provider but they seem to be unable to assist and have had no luck with Linksys support either as all they want to do is pass it back to my ISP/VOIP provider saying they are the one to reconfigure it but I'm the person who did the config (and also shot myself in the foot incidentally). If I could only reset the voice side of the router back to factory defaults I would be fine but, unlike the WAG310G, there is no option to do this, just the option to reset the WAN/LAN/Wireless side to factory defaults. I've tried pressing the reset button for 30s and reset via the menu option but neither reset the voice side. Surely there must be some way to do this even if it involves opening the box up and connecting a jumper or something.
I have a modem Scientific Atlanta 2100. I just installed windows 8 pro 64bit and when installing the driver to use the usb cable modem does not recognize it and simply not installed. I wonder if it is possible to use my usb cable modem or simply incompatible with my windows 8 64bit pro.
View 3 Replies View RelatedWith this modem, can you hook up to the Linksys Smart Apps WiFi?
View 2 Replies View RelatedOur family has about three computers that use a wireless network that we all share. We have an old Gateway, a WCG200, that is bridged to an E2000, which was set-up ever since we required better security when someone used our connection to illegally obtain movies. We got a letter which warned us of any future violations that could cause legal action, so we looked into our wireless connection to better secure it from any other individuals outside of our household. The WCG200 is connected to the outlet in the wall via cable, and then connects from the Ethernet to the E2000. The E2000 has a stronger security setup than the WCG200, which is the advice we received from our ISP and would allow us to keep the Gateway. It provides a strong signal, but from time to time, we suffer latency or slow loading through all of our online devices, even though our connection speed displays a solid 72.0 Mbps. I've tried the Event Viewer to see any problems, and I have noticed some small things:
- WLAN AutoConfig service has successfully stopped.Wirel?
- WLAN Extensibility Module has stopped. Module Path: C:WindowsSystem32cmihvsrv64.dll
- The server {E10F6C3A-F1AE-4ADC-AA9D-2FE65525666E} did not register with DCOM within the required timeout.
- Broadcom NetLink (TM) Gigabit Ethernet: The network link is down. Check to make sure the network cable is properly connected. [This last one is strange, since I use the Wireless Network Connection with a DW1501 Wireless-N WLAN Half-Mini Card, while the Broadcom adapter is under the Local Area Connection and displayed as not connected.]
Other than that, I'm not quite sure what the recurring problem comes from. Our WCG200 has a firewall enabled and our E2000 has an SPI firewall enabled. The security mode of the E2000 is a WPA2 setup. We have disabled the wireless network of our WCG200 in order to make use of the E2000.
I have a WAG160N wireless gateway . Yesterday when i tried to power it on after a couple of seconds the power led was solid green and the Ethernet leds were blinking with no Ethernet cable attached to the router . The ethernet leds would keep blinking for minutes . I tried to use a screwdriver to do a hardware reset ( with power on ) and i noticed that the power led would start blinking green/red for minutes . I tried to use another wired router which i have for backup and it could connect to the internet normally without a problem.
What the green / red blinking power led means ( power led is green and then changes to red and then it starts over ) ?
I inherited a BEFCMU10 v.3 cable modem from my boss who switched to FiOS and I would like to use this with my Comcast connection.All I received from him is the cable modem and power adapter, what do I need to install and get this cable modem working? My router is WRT-54G.
View 2 Replies View RelatedI can't get a new IP from my ISP when my Cable modem router(EPC3925) is set to router mode, i have tried factory restore, unplugged etc..but still no luck. It changes each time i reset it when i set it to bridged only mode but then i won't be able to connect other devices to it since it doesn't uses DHCP in bridged only mode. It changes back to the IP i had when i set it to router mode. I don't want to change my router settings to bridged only because it would disconnect the other devices in my house. Why my ISP assigns the same IP address when it's set to router mode but assigns different IPs when it's set to bridged only, how is this possible ?
View 1 Replies View Relatedsome reference material about configuring my WAG320N to use my cable modem via Ethernet port 1. I've seen it mentioned that's its possible, however I've been unable to sort it out myself.
And before you ask, I've brought the DSL router as I'm moving in the next 12 months and my new base will not have access to cable internet and I'll be reverting back to DSL.
Is it possible to set up additional PVC for IPTV on LinkSys x3000?
View 4 Replies View RelatedBest modems for PS3?
View 1 Replies View RelatedHow can i add several vpi / vci to my Linksys x2000 ?
View 7 Replies View RelatedJust picked up a X2000 and Cisco connect configured my connection, and assigned an IP to my desktop pc.I configured my PC back to a Static IP which is outside the DHCP range in the X2000, and all seems to be working ok..now looking in the web-based X2000 setup screen my pc is no longer listed as a client...so should I manually add it as a client and assign the IP & MAC address in the Cisco setup or is this not necesary.?
View 5 Replies View RelatedI have a WAG320n and I wish to use it as a modem only so that I can use an Airport Extreme as my wireless router. how to configure the WAG320n so that it can be used in this configuration?
View 1 Replies View RelatedGot 300 Mbps with Linksys X3000 in real life?I haven't seen it working at 300 Mbps since I've bought it, so I wonder whether it is truly possible. The maximum speed I've seen was 130 Mbps.
View 7 Replies View RelatedI want to use WAG54G2 as plain router. I happen to have 2 of these. If i can make one of these work as router wired to another through ethernet cable or even wireless i can save some money on router.
View 8 Replies View RelatedI have the X2000. It has 3 ports. I need 4. I also have the WRT160N V3 router which has 4 ports. Is there a way to use this router with the X2000 to get the 4 ports I need ? If not, what are my other options to get 4 ports ?
View 2 Replies View Relatedhow to configure or set up VPN on WAG320N?
View 3 Replies View RelatedI have an intermittent issue with a new WAG320N.Device is new (installed for 1 month now) and is running the latest firmware "out of the box".
Device was confirmed as working (recommended) via the ISP, as it uses a Broadcom chipset, so it works "more reliably" with the ISP's hardware which uses the same chipset.
Setup was painless and the router synced up fine and has been operating for a few weeks. However, twice in the past week the router has become unresponsive to ping over the LAN. Furthermore, the device's lights indicate everything is OK, however I have to reset the router (power cycle) and then it returns to normal.
WIFI is OFF. LAN IP is set manually, DHCP is OFF. The router is plugged into it's own UPS.
I've tried everything to get this to produce an i.p address but to no avail.I check with my ISP (o2/BE) they told me all my settings are correct it syncs but just does not pick up an IP address.
View 6 Replies View RelatedHow to configure settings for router E4200I live in Finland and bought new Cisco Linksys WAG320n router modem as I am experienced Cisco user. However after spending several hours and setups on the WAG320n router I cannot get it to connect on the ISP ADSL line.
RFC2684 Bridged
LLC/SNAP
g.dmt or ADSL2+
VPI 0
VCI 100
But once I setup these or acutally any other setting I cannot get the router to connect. With the right settings I can get the DSL PVC status up and connected but the ModemRouter cannot connect and retrieve IP-address from ISP.
I'm trying to play some online games and my WAG320N does not forward ports, upnp does not function and to top it off DMZ wont even work (not a software firewall issue either). I have the latest firmware (and honestly the stock firmware is terrible).
Am I out of luck or is there something I can do to fix this? I sure as hell will be steering clear of linksys products after this.
i need to downgrade my WAG320N and don't find old firmware 1.00.08 AnnexA
View 9 Replies View RelatedLog enabled using [URL] , config saved, modem power cycled...... no in and out log after internet use.
View 1 Replies View Relatedlinksys x 2000 modem unfortunately, when I turned the modem on today, the power light which normally was white became red.I tried all the ways I knew, such as restarting in 5 or 30 seconds intervals but unfortunately it didn't work
View 3 Replies View RelatedThis WAG320N Router can get really slow after a while use which is really frustrating for me since I am a gamer. Power cycling it SOMETIMES does the trick but it will still get slow. It has been slow just now and over here it is midnight so the internet peak should be down and my internet should be faster but its now.
View 2 Replies View RelatedI would like to know how to properly setup my old wag354g as a wireless ap. should i select from basic setup as "bridge only" or the "rfc bridge"?
wag354g will be connected by wire and supply wireless on laptops with b/g.
I'm currently researching in buying a new modem/router that must have the PPPoA support for the ISP, i'm wondering if the X3000 is compatible with the DD-WRT firmware? or in this case any other firmware that has a top notch QoS, We have a troll in the house that downloads too many torrents and would like to limit his bandwidth .
View 1 Replies View RelatedTrying to replace old modem with the X2000 but it will not connect to the internet, my provider is ATT DSL.
View 2 Replies View RelatedIs there any way to disable WPS feature on my WAG120?
View 1 Replies View RelatedJust bought this WAG120N and using the CD Setup it gets as far as Install Gateway then displays its not connected properly. Checked everything it says to check.Im swapping from an ordinary adsl modem but i unplugged all of that and the WAG120N shows steady Power , 1 ethernet number lit and flashing ok, Wireless is lit and DSL is also also lit. Rebooted a few times too.
View 1 Replies View Related