Linksys WRT54G Wireless-G Router Not Connecting To Internet Via Wire?
May 1, 2011
I wired it all up correctly, and Continue to get "error 322: check router" upon every attempted install. I did some research and tried releasing and renewing IP amongst restarting all networking devices AND PC's. Peculiar enough, I could connect AND get online wirelessly from a netbook, but neither of my 2 PC's could connect via a wire. I got a defective router, is it possible the ports are malfunctioning? because the lights are on, but 3 or all of the 4 lights are continually on when only 2 ports are plugged in
View 5 Replies
ADVERTISEMENT
Feb 5, 2013
I am recieving error 619 (port for connection was closed) when trying to connect over my wireless connection. If I disconnect the WRT54G and hard wire to the cable modem I can VPN in without a problem. I have enabled IPSec / PPTP / L2TP on the VPN security tab and have reset the wireless modem.
View 4 Replies
View Related
Oct 17, 2010
Is it possible to get a WAP54G wireless access point working with a WRT120N wireless router, by wiring the 2 devices together?
View 6 Replies
View Related
Jun 24, 2011
I just installed windows 7 into my computer and I need to verify my copy of windows. I tried connect my Ethernet wire from my computer to the wireless router but it's not connecting or registering. The wireless router is a WRT54G and I can access the device ip for it but I don't know how to assign an IP address for the new computer. I already had a computer (wired) and a laptop (wireless) connected to the router. I'm using a straight trough Ethernet wire Doing the steps in the sticied post below didn't work because typing ipconfig /release didn't work?
View 5 Replies
View Related
Jun 28, 2012
i was using one internet wire to pc as well as laptop but not at same time . whenever i need i used to remove it from PC n then connect it to laptop. but now i can get connect to PC but whenver i try to connect it to laptop it only redials . i have dial up connection n all things are correct , username password . what can i do now ? i heard something about copying physical address to laptop.
View 2 Replies
View Related
Jun 6, 2012
We are running our internal network on the 192.168.1.x range.
Â
We have just installed a new control system which is running on a closed 192.168.0.x network (no internet access).
Â
What we need to do is use the WRT54G to connect the 2 networks together so that we can VNC into one of the computers on the control system network so that it can be managed.
Â
I have tried connecting the two networks by plugging the 192.168.0.x network into the WAN/Internet Port on the WRT54G, and setting the "Internet Connection Type" to "Static IP" and setting the "Internet IP  Address :" as 192.168.1.200 (the main PC I need to VNC into) but cannot ping any of the other computers..
View 7 Replies
View Related
Apr 29, 2008
I have a WRT54G wireless router ... I want to connect a new laptop through it ... but I need either a network key or a password ... cant locate these ..
View 8 Replies
View Related
May 8, 2012
It constantly disconnecting and wouldn't stay connected for a long period of time, so I tried messing with the settings and it no longer connects to the internet. It tells me that the settings for this router is not compatible for the computer settings. I have reset the router to its factory settings, restarted the computer, restarted the router but nothing changed. I have tried plugging my computer to the router via ethernet cord and typing in 192.168.1.1 in the address field of Internet explorer and nothing comes up. I also forgot the password to the router!
View 1 Replies
View Related
Aug 19, 2012
It is a wired, not wireless connection. The light isn't even coming on for the port it's plugged into. I tried a different cord, a different port, upgrading the firmware, and restarting each device. Nothing has worked so far.
View 9 Replies
View Related
Feb 27, 2012
My WRT54G router locks up 100% of the time when attempting to connect connect wirelessly to a Samsung Blue Player (Model number BD-P3600). I can connect to it with a cable no problem, but when I attempt to do so wirelessly and type in the password on the Blue Ray player, it attempts to connect but the router locks up and all devices connected to it (wired or wirless) lose connectivity
View 1 Replies
View Related
Feb 16, 2010
I can't get my Epson Workforce 615 (610 series) All in One Printer to connect to my WRT54G router. I was on the phone with Epson for over an hour and renetered my SSID and security code 4 times. They said it was something about the router not letting it connect. The printer sees the SSID and I put my laptop in the same location as the printer and it has very good signal strength. I even took the printer back and got another one. The router does not have MAC filtering enabled.
View 5 Replies
View Related
Sep 30, 2012
I am trying to connect a Zodiac iAqualink wireless pool equipment controller to my home network (WRT54G) without success. This is a 802.11b device. My router is set to mixed mode. What I have tried:
1. Set it up as suggested in the instructions: WEP2 security, double checked SSID and password
2. Set it up without wireless security
3. Changed channels
4. Set mode to 802.11b
Â
In all cases the LED on the iAqualink that is supposed to indicate that it is connected to the network illuminates properly, but I can never find the device using EasyLink Advisor.
View 9 Replies
View Related
Jan 17, 2012
Running Win XP (no service pack), WPA personal. Two other computers connect fine. On an old laptop running Win XP the network card sees the router, but when I enter the correct passcode (16 character) I get a message saying the code must be 13 characters. How can a connect this computer without disabling the other two wireless devices running through the router?
View 2 Replies
View Related
Feb 16, 2013
I've got a WRT54G v6 that is password protected via WPA2 Personal TKIP+AES, and SSID broadcast enabled. In the Status menu > Local Netork > DHCP Clients Table there is a MAC Address listed that none of my devices have.
View 6 Replies
View Related
Jun 27, 2011
I buy WAG160n wireless-n adsl2+modem router with wire it works but it not connect without wire and i cant connect internet through my pc.
View 1 Replies
View Related
Jul 30, 2009
I've been having a ton of problems with fixing my connection with my wireless network. A few months ago, I lost connection on my desktop computer and I reconnected... however, it didn't actually connect. When I hovered my cursor over the Wireless Network Connection icon, it just said "Acquiring Network Address" and never connected. I got onto my laptop and did a quick search on the problem. A few wrong moves later, and I couldn't even find my wireless network.
Â
Despite all of my attempts at creating a connection, I still have no internet. I've even tried plugging my computer into my WRT54G router via cable, and still no connection. It's not the router that's the problem, though, as my two other computers and xbox have perfect internet connection.Â
Â
I use Windows XP, I use a WRT54G router, I have Mediacom high speed internet, and that's about all I know.
View 9 Replies
View Related
Feb 6, 2011
when connecting my router to my tv are the wire colors thru or crossed
View 2 Replies
View Related
Nov 16, 2011
I have a linksys router WRT54G connected to a modem supplied to me by Time Warner Cable. Just last night, for some reason my internet stopped working. After calling Time Warner Cable internet support, I found out that the modem is working. If I connect my laptop (Dell model which is running on Windows 7) directly via cable to the modem, I can connect to the internet. BUT if i connect my modem to the router, and then connect my laptop via cable or wireless to the router, I can't connect to the internet. When I open up my network window on the computer, I see that my laptop is connected to the router and the router is connected to the internet but I can't connect to the internet. I tried calling linksys customer service and my insurance ran out so yea ... On the laptop, i ran a troubleshooting program and it gave me an error stating that it failed to connect to the DNS server and I should contact the internet provider. Time Warner Cable told me that if connected to the modem directly, I could access the internet indicating that there's an error in the router.
View 1 Replies
View Related
Sep 5, 2008
I have a linksys system WRT54G at home. I had no problems with the Linksys router until about a month ago when I decided to make it a secure network. I run three computers of the wireless router (1 desktp and 2 laptops) Since making the wireless network secure I can not connect with my business laptop IBM Thinkpad X40, but thother e computers work just fine.
View 8 Replies
View Related
Jul 8, 2011
My 'network' looks like this:
Â
CABLE MODEM ===> WRT54G
WRT54G Port1 ===> PC
Â
PC is running Windows/XP sp3 with all updates installed. It has no wireless adapter.WRT54G model number sticker shows ver.2. I don't think the firmware has ever been upgraded.This used to work. What has changed? The laptop that used to connect wireless is dead. I now have a 2nd PC that sits on the same table as the old PC. It has no wireless adapter at this point, but eventually either it, or the old computer, will be getting its internet connection wireless-ly, as the computers will be physically in separate rooms. I can't see how these changes would affect the operation of the router.
View 9 Replies
View Related
Sep 26, 2012
I had connected my WRT54G to my wireless router by disableing the DHCP on WRT54G. It worked great until recently. Now I upgraded my linksys box to the latest and greatest AC1750. Iwant to use complete features of AC1750 router. So to do this, How do I connect Verizon Model(its modem+wireless router) to this Router and have AC1750 drive everything.
View 1 Replies
View Related
Nov 18, 2011
I have a Linksys wrt54g wireless router.I have my modem connected to it through ethernet. All of the lights on my modem are on, except for the standby light which isn't supposed to be on. My router says it has internet and it says wlan is active. But still no internet. I get local only. I went on my setup page for my router. I went to status and its telling me that my ip address, subnet mask, and default gateway are all 0.0.0.0 All 3 dns spots are blank. I did a dhcp release and renew. Still all 0's. I did factory defaults. Still nothing. I did ipconfig /all on my desktop and its listing my dns, my default gateway, my dhcp server, my ipv4 address and my dns suffix.
View 6 Replies
View Related
Sep 22, 2011
Router: WRT54G
Network: 802.11g (and I'm using WEP)
Wifi Adapter: Intel R Centrino R Ultimate-n 6300 AGN
No. of devices connected to wireless network: 5
My problem is that whenever 2 devices have joined the wireless network, I will not be able to do so despite placing the laptop or iPhone right next to the router, hence getting excellent signal strength. Or, if I am already connected to the network, I get knocked out repeatedly. I don't think it is a hardware or software issue because I'm still able to connect and get a very stable connection after someone leaves the wireless network.This is getting frustrating and I have tried all ways and means to resolve this but to no avail. Is this about some setting that I can tweak, e.g. to allow more users onto the network? But this has already been configured to '50'!
View 7 Replies
View Related
Oct 12, 2010
I am replacing a WRH54G with a WRT54G. Â First I unplugged everything and waited 5 minutes. Then I plugged my ethernet cord from the DSL modem into the WRT54G. Then I plugged in the DSL modem. I waited for the lights to stop blinking. Then I plugged in the WRT54G and waited for LEDs to show connection. Then I plugged the ethernet cord from the WRT54G to the computer. Then I turned on the computer. I was able to access the Interface for the WRT54G but I was not able to connect to the internet. I tried power cycling multiple times both the DSL modem and the WRT54G. I was unable to access the internet. Finally I plugged the WRH54G back in and everything worked fine. why the old WRH54G can connect to the internet and the WRT54G cannot?
View 9 Replies
View Related
Nov 19, 2011
My router used to work. I updated the firmware to 4.21. xx and after that I can't connect to internet.When I connect directly to modem, I can go to the internet . I power recycled etc but when I connect to the router, it says limited connectivity. It shows autoconfigurtion ip:169.254.251.135. I don't know why this is so.I don't have the setup cd disk but I read the users' guide and it seems that I really don;t need the cd. But no matter what I do , I can't get to 192.168.1.1 .
View 4 Replies
View Related
Nov 23, 2007
I just switched from DSL to Cable and now i can't get internet to the Linksys router. I can connect to it from a wireless laptop but just not get on the internet I've read other posts about doing the "clone mac" address and doing the power cycle but still cannot get the Linksys to respond. I enabled the WRT54G to clone the mac address and have spent about 10 hours in two days trying to get this to work and looking online, etc....
View 7 Replies
View Related
Aug 28, 2011
I have a wrt54g v5 router. I cannot connect to the internet through my router. I called the cable company and they told me that the router probably reset from a power outtage and reconnect. i power cycled, i tried to log onto the router via 192.168.1.1 but the connections were spanish to me.
View 2 Replies
View Related
Jul 29, 2006
I am havng a problem with my WRT54G v5. I have 2 laptops that cannot connect to the internet using wireless. I connect them to my home lan using wireless and look at files on other computers but no internet. When I connect the laptops using ethernet they both access the internet fine. I also have 3 desktops (using ethernet) which work fine. I have tried the followingTurning off wireless security and laptop wire wallsDownloading latest firmwareChecking TCPIP settings Using a WRT54G v6 router - same problemIpconfig shows connection to the router at 192.168.1.1 and an address of192.168.1.100. I can ping 192.168.1.1 successfullyMy internet provider is VerizonThis worked at one point in time (May) but has not worked since June.
View 8 Replies
View Related
Dec 29, 2011
wrt54g wireless router so we could get Netflix through our Wii. I have a one year old Compaq and am running Windows 7 with a wireless Internet connection through my service provider. I installed the router with no problems and was able to get online with the Wii. However, I am no longer able to get Internet access on my desktop. It shows that my Internet is connected, but it shows "No Network Access". I had gotten on fine at first, then I went to the 192.168.1.1 site to configure my data. I changed my time zone and then went to secure my connection. I cannot remember the exact option I chose, but I think it was something like WAP2 Personal. As soon as I selected that the screen froze and I can no longer access that site or get online through the router.
View 3 Replies
View Related
Aug 28, 2011
I went to set up a passowrd on the my WRT54G. I actually clicked SES and pretty sure i pressed reset security. Does this reset the router to factory default? Or the security settings to factory default?I didn't save after realising that I had done wasn't going to change my password.Now I can't access the internet. I have tried everything, resetting, restarting, waiting, banging my head aqgainst the wall.I have another router, an E1000. This will not connect either. internet works fine when hardwired to the modem.
View 2 Replies
View Related
Aug 5, 2011
I have a WRT54G wireless router and it goes through periods where it constantly has to be reset cause it keeps dropping the internet connection. Once you do a power cycle it starts working right again. But sometimes goes out 5mins later.I have the router hooked up to a Windows XP computer via an ethernet cable...and I have 1 Windows Vista laptop, 2 Android phones and a PS3 connected via wireless.The PS3 is set up following these directions: (not sure if this is what's screwing it up)
Â
"Step 1:Open a web browsersuch as Internet Explorer.
Step 2:Go to the Address bar and enter your router's IP address ("192.168.1.1" is the default IP of most Linksys routers) then press [Enter].
Step 3:When the router's web-based setup page appears, click Applications& Gaming then click DMZ.
Step 4:Select Enable on DMZ and under DMZ Host IP Address enter the PlayStation®3's IP address.
- Try 192.168.1.10 or 192.168.1.20 Save Settings.
- This IP address will need to typed in manually during online setup on ps3. I think its the first address you enter (I think this is the game's IP address).
- Use 192.168.1.1 for the wireless router's IP address on your PS3.
Step 5:Now, click Administration and Disable UPnP. Make sure you also disable UPnP on your ps3 online setup. Save Settings.
Step 6:Click Status. Write down the DNS 1: dns number and DNS 2: dns number on a piece of paper. You will enter these for DNS 1 and DNS 2 numbers during online ps3 setup. NOTE: The IP address listed on the Status page for your wireless router is not used for any setup on your ps3. Remember, to get into ps3 online setup, you have to choose Manual during setup so you can enter these numbers.
Step 7:The WP key crap and whatever during online setup should be skipped unless you specifically setup some kind of password for your wireless router when you installed it. I didn't and just left that part blank and skipped over it.That should get your wireless router and game setup. If you're still stuck, drop me a message.And, remember to do this setup after that:Linksys has a great tech support at their site. url...
I have a ps3 and did all of the wireless and ps3 online setup for it using their site technical support. Doing that seemed to throw a monkey wrench into my internet connection a while after that. I just left all of my game settings in place and did this: Logon on to your wireless router. To do this, you will probably go to url.. by typing this address into your address box on your internet explorer. Logon. If you don't know how to logon, go to and follow the instructions in technical support.
View 1 Replies
View Related
Jul 4, 2011
I just got a Linksys router from a moving neighbor. Â The router is a Linksys WRT54G v5. She didn't have the power adaptor, so I found one that is 12VDC 500mA and it works. Â The factory resetted the device. Â I always get a signal, but it has that little error sign on it. Â It says my internet connection is broken. Â I believe this is caused by a bad ethernet port, but I have gotten into the internet sometimes. I have another router but it doesn't work either. On the other router I get a signal that as no error sign and says "Internet Access" but I still cannot access the internet. Â My laptop's network card works.
View 2 Replies
View Related
Sep 25, 2011
I have a problem with my new Galaxy S2 and getting Internet connection trough my Linksys-router. I can connect to the router and my S2 shows and says my WIFI-connection is OK. But still I can't get any Internet-traffic to my S2.The wireless router is working OK for my old IPhone and MacBook Pro, but not for my S2. I have tried the S2 on other wireless access points, and it is working fine.I have tried a lot of different wireless settings, but nothing seems to fix the problem.From my S2 I can ping the IP-addresses of the router, all DNS, gateway and IP-address of the router. I can also ping the phones IP-address from my router. But I can't ping anything "outside" the router.Here are some data:
Router: WRT54G 
Hardware-version: 2.2
Firmware Version: v4.21.4 
View 3 Replies
View Related
