It is a wired, not wireless connection. The light isn't even coming on for the port it's plugged into. I tried a different cord, a different port, upgrading the firmware, and restarting each device. Nothing has worked so far.
View 9 RepliesI have WRT54G router. The VIZIO VBR231 unit finds the network OK and indicates it is connected, but nothing will stream, and when I run a Network Test it gives me this 3 line error:
Connection to 0.0.0.0... successfully established
Resolving... could not be established
Please check your connection and try again.
The VIZIO support folks were not beneficial at all, and said something about Port 80 or Port 43 not being open or available. When I talked to linksys support, they said I needed to add the VIZIO player's IP (which appears to be 0.0.0.0 in the system settings). I poked around a bit, including the Port Forwarding tab on the router setup, but could not see a way to assign 0.0.0.0 to one of these ports, and I am hesitant to experiment.
I'll probably just return the unit to Costco, but I'm trying this forum as a last ditch effort. BTW I have a VIZIO internet TV that I love, and that had absolutely no problem at all connecting to the wireless.
I have a WRT54G router and for some reason I'm unable to receive the media stream at my home, but when I connected to my friends N-type router it works fine. I have no other connectivity issues. The only thing that I remember doing that may have caused this was to upgrade my firmware because my droid phone wouldn't connect.
View 8 Replies View RelatedI use a Cisco 871W router for my office in home -- I have Wifi working and want to add my new Blu-Ray player to the network -- I bought a WAP54G to use as a wireless bridge assuming i woudl just connect the WAP to the BLU-Ray with a ethernet cord. The instructions for installation of the WAP include connecting it to my router for the set up but the installation disk says it is not recognizing the WAP. I use Brighthouse for my ISP and the connection sequence is BH Modem to teh Cisco 871W -- the 871W directly connects to my CPU and to a Net gear FS105 fast network Switch -- the swicth connects to my VOIP phone , HP printer and external HD back-up system -- there is an open port onthe FS105 and two open LAN ports on the 871W.
I tried to install the WAP but connecting it to both the router and the swtich without luck. Is the WAP what I need to connect the Blu-Ray --- am i missing something in the set up?
I've switched over from a d-link dir-655 router to the v1 4200. I've been playing around with the 4200 and trying to get it connected to my tv all night long. I have two laptops and two iphones connecting with no issues. I cannot for the life of me get the tv (GT30) to work. It picks up three signals, the 2.4 signal, the 5 signal and the guest signal. The only one that will even connect to the internet is the guest signal. When I run the connection test, however it will not connect to the vierra connect server. I've tried setting it up manually, and anything else that seems obvious. I had no issue with the dlink router at all.
View 1 Replies View RelatedWe are running our internal network on the 192.168.1.x range.
We have just installed a new control system which is running on a closed 192.168.0.x network (no internet access).
What we need to do is use the WRT54G to connect the 2 networks together so that we can VNC into one of the computers on the control system network so that it can be managed.
I have tried connecting the two networks by plugging the 192.168.0.x network into the WAN/Internet Port on the WRT54G, and setting the "Internet Connection Type" to "Static IP" and setting the "Internet IP Address :" as 192.168.1.200 (the main PC I need to VNC into) but cannot ping any of the other computers..
I have a WRT54G wireless router ... I want to connect a new laptop through it ... but I need either a network key or a password ... cant locate these ..
View 8 Replies View RelatedIt constantly disconnecting and wouldn't stay connected for a long period of time, so I tried messing with the settings and it no longer connects to the internet. It tells me that the settings for this router is not compatible for the computer settings. I have reset the router to its factory settings, restarted the computer, restarted the router but nothing changed. I have tried plugging my computer to the router via ethernet cord and typing in 192.168.1.1 in the address field of Internet explorer and nothing comes up. I also forgot the password to the router!
View 1 Replies View RelatedI wired it all up correctly, and Continue to get "error 322: check router" upon every attempted install. I did some research and tried releasing and renewing IP amongst restarting all networking devices AND PC's. Peculiar enough, I could connect AND get online wirelessly from a netbook, but neither of my 2 PC's could connect via a wire. I got a defective router, is it possible the ports are malfunctioning? because the lights are on, but 3 or all of the 4 lights are continually on when only 2 ports are plugged in
View 5 Replies View RelatedMy WRT54G router locks up 100% of the time when attempting to connect connect wirelessly to a Samsung Blue Player (Model number BD-P3600). I can connect to it with a cable no problem, but when I attempt to do so wirelessly and type in the password on the Blue Ray player, it attempts to connect but the router locks up and all devices connected to it (wired or wirless) lose connectivity
View 1 Replies View RelatedI can't get my Epson Workforce 615 (610 series) All in One Printer to connect to my WRT54G router. I was on the phone with Epson for over an hour and renetered my SSID and security code 4 times. They said it was something about the router not letting it connect. The printer sees the SSID and I put my laptop in the same location as the printer and it has very good signal strength. I even took the printer back and got another one. The router does not have MAC filtering enabled.
View 5 Replies View RelatedI am trying to connect a Zodiac iAqualink wireless pool equipment controller to my home network (WRT54G) without success. This is a 802.11b device. My router is set to mixed mode. What I have tried:
1. Set it up as suggested in the instructions: WEP2 security, double checked SSID and password
2. Set it up without wireless security
3. Changed channels
4. Set mode to 802.11b
In all cases the LED on the iAqualink that is supposed to indicate that it is connected to the network illuminates properly, but I can never find the device using EasyLink Advisor.
Running Win XP (no service pack), WPA personal. Two other computers connect fine. On an old laptop running Win XP the network card sees the router, but when I enter the correct passcode (16 character) I get a message saying the code must be 13 characters. How can a connect this computer without disabling the other two wireless devices running through the router?
View 2 Replies View RelatedI've got a WRT54G v6 that is password protected via WPA2 Personal TKIP+AES, and SSID broadcast enabled. In the Status menu > Local Netork > DHCP Clients Table there is a MAC Address listed that none of my devices have.
View 6 Replies View RelatedI've been having a ton of problems with fixing my connection with my wireless network. A few months ago, I lost connection on my desktop computer and I reconnected... however, it didn't actually connect. When I hovered my cursor over the Wireless Network Connection icon, it just said "Acquiring Network Address" and never connected. I got onto my laptop and did a quick search on the problem. A few wrong moves later, and I couldn't even find my wireless network.
Despite all of my attempts at creating a connection, I still have no internet. I've even tried plugging my computer into my WRT54G router via cable, and still no connection. It's not the router that's the problem, though, as my two other computers and xbox have perfect internet connection.
I use Windows XP, I use a WRT54G router, I have Mediacom high speed internet, and that's about all I know.
I have a linksys router WRT54G connected to a modem supplied to me by Time Warner Cable. Just last night, for some reason my internet stopped working. After calling Time Warner Cable internet support, I found out that the modem is working. If I connect my laptop (Dell model which is running on Windows 7) directly via cable to the modem, I can connect to the internet. BUT if i connect my modem to the router, and then connect my laptop via cable or wireless to the router, I can't connect to the internet. When I open up my network window on the computer, I see that my laptop is connected to the router and the router is connected to the internet but I can't connect to the internet. I tried calling linksys customer service and my insurance ran out so yea ... On the laptop, i ran a troubleshooting program and it gave me an error stating that it failed to connect to the DNS server and I should contact the internet provider. Time Warner Cable told me that if connected to the modem directly, I could access the internet indicating that there's an error in the router.
View 1 Replies View RelatedI have a PC network in house using a netgear router. One of the PC is cable-connected to the router and the other using wireless network adapter. Now I have a Sony Blueray player which support network connection. How do I connect it to the network?
View 1 Replies View RelatedWe're using our Sprint hot spot and want to make a wireless connection to the TV...can I use the AE1000 for this? If not, what do I need to use?
View 2 Replies View RelatedI have a linksys system WRT54G at home. I had no problems with the Linksys router until about a month ago when I decided to make it a secure network. I run three computers of the wireless router (1 desktp and 2 laptops) Since making the wireless network secure I can not connect with my business laptop IBM Thinkpad X40, but thother e computers work just fine.
View 8 Replies View RelatedI recently purchased the Magnavox MBP5130/F7 Blue-Ray player. I have been trying to get the player to connect to my wireless network so that I can stream Netflix. I am using a Linksys router. It seems to be a similar problem to the one that Adie of Texas was experiencing. I looked through that thread and did the same things but still cannot get it to connect to the internet. It will connect to the wireless network but will not connect to the internet. The first night I purchased it I some how got it to connect and it updated. Since then I have been out of luck.
View 5 Replies View RelatedI had connected my WRT54G to my wireless router by disableing the DHCP on WRT54G. It worked great until recently. Now I upgraded my linksys box to the latest and greatest AC1750. Iwant to use complete features of AC1750 router. So to do this, How do I connect Verizon Model(its modem+wireless router) to this Router and have AC1750 drive everything.
View 1 Replies View RelatedI recently bought the Panasonic Viera THL37S25A TV and wanted to connect it to my home network. Just wondering whether the WUSB600N USB adapter will be compatible with the TV.
View 2 Replies View Relatedim moving into an apartment that provides internet via a wireless hotspot (is PW protected and has WPA2 protection). I would like to be able to connect a router to it and then wire my printer, Media server and Roku device to my router.im guessing I will have to somehow bridge my router to the wireless hotspot. I would like the ability to then broadcast my own wireless network from my router, and have my mobile devices connect only to my router, which is in turn connected to the internet via the hotspot.can use the mfg firmware or be open source firmware, doesnt matter to me.I currently have a Netgear WNDR3700 and a spare WRT54G with DDWRT.
View 3 Replies View RelatedI have an E3000 with an external hard drive attached via USB with several movies saved on it as ISO's. How to stream a movie to my wireless blu ray player, Sony S580. I was able to stream the iso to a netbook attached to the LCD tv by using VLC on the netbook. The only videos I can access on the blu ray player that are on the external hard drive are home videos I converted to DVD quality before uploading, they're not HD. I can access pictures and music on the blu ray from the external hard drive as well. I tried converting an iso to MVK but was unable to access/find it using the blu ray player.
View 2 Replies View RelatedI am unable to see my network media player (wired CAT6 or wireless) using the SAMBA Share feature. My UPNP works fine. I do not have this issue when I am using the Linksys WRT54G or a Netgear WNDR3700 (I returned it to give the E3000 a try) - so I know all my share persmissions and device firewall is turned off. How do I get it to work with the E3000? I want to be able to transfer and stream media files to my media player using SAMBA. Usually my network media player automatically detects SAMBA Servers/Devices and adds it to its list for me to access. But when I use the E3000 that is not the case.
View 4 Replies View RelatedI am unable to get this to hook up my vizio dvd player to wifi
View 2 Replies View RelatedI have an e1200 Linksys router hooked up and working well, a wired connection to my first computer a wireless connection to my second (laptop) in the basemen and to my HDTV. My question is what Linksys device would I need to enable me to get a wireless connection in the basement to then hardwire connections to my Blue-Ray player and my HK AVR-3650.
View 2 Replies View RelatedI am not wanting to use my router as I have disconnected it all together. I ran an ethernet cable from the back of my dvd player to another room where my computer is. I plugged ehthernet cable to computer. And dvd player saying no network.
View 1 Replies View RelatedIm trying to connect my Magnavox MBP5220F Blue Ray Player to my Netgear N300 wireless router, with no luck. It keeps saying DHCP not acquired.I did the ipconfig/all, and here are the results. [code]
View 1 Replies View RelatedHow do I connect one dvd player to four direct tv boxes?
View 1 Replies View RelatedI've bought a LG HR536D Blu-ray player w/ HDD, and it has DLNA compability, but is well out of range for a wired connection to my wireless router. So, I thought since that all the things that I'd like to watch are on my laptop (Win 7 64-bit) which is in the same room, within reach for an ethernet connection. I have plugged in the ethernet cable, but predictably, they won't talk to each other. And I have no idea how to make them do so. I messed around with matching the IP Addresses, and Bridging the connection with my Wireless connection, but to no avail.
View 1 Replies View RelatedMySony BDPS570 will not pick up the wireless signal from my router which is sited about 12 feet away through two breeze block walls. A laptop placed next to the BDPS570 has no difficulty in making a connection. In the past I have overcome this problem by using two Netgear AV200 Powerline devices. However, I now require the Powerlines for a TalkTalk Youview connection and am looking for a cheap and elegent method of reconnecting the BDPS570. I could just buy another ethernet cable and swap it for the Youview one when I want to use the 570 but that seems a bit of a fag
View 3 Replies View RelatedI have the E1000 Linksys Router and I am using a network cable to connect to my Sony Blu-ray BDP-S370. When I watch HULU through the player it kills the entire internet connection for all PCs. I have to unplug the router in order to restart it. Everything will also work just fine until the next crash.Here's the thing, I'll watch a bit of the show and see the commercials and the router will only crash when it comes back to the show. If I watched 100 commercials they would not crash, but as soon as it returns to the show CRASH. Restart and we watch again.
View 2 Replies View Related