Linksys Wired Router :: BEFSX41 - Slow Downloading And Uploading On UTorrent
Dec 30, 2011
I have an issue with slow downloading and uploading on u torrent with my wired router linksys BEFSX41. I thought it may be because I didn't set port forwarding on the specific ports the u torrent use.
But every time When I try to set new port forwarding rules on my router's control panel its asks me for a password and user. Although I know this password and user it will keep asking me about them without saving the new port forwarding settings.
View 1 Replies
ADVERTISEMENT
Mar 21, 2013
I use in my network Linksys 4200v1 (newest firmware) and Sipura SPA 3000 ( 3.1.20(GW)firmware) and SPA 122 (1.1.0(011) software version as my phone adapters.My voip phones are working great until I start to download or upload some files, watching on-line tv.How and where should I set up above routers to have the same great quality voip while uploading and downloading at the same time?
View 4 Replies
View Related
Feb 4, 2012
I've been struggling to resurrect an older V1 BEFSX41, which suddenly decided to suffer continuous collisions and loss of link. Had been running for several years. I reflashed the firmware with TFTP to 1.52.16.4, and reset for 30 seconds, and re-powered. I am unable to get any response form the web UI. I can ping 192.168.1.1, and obviously push the BIN image to it, but the UI doesn't give any sign of life - not even an error - just blank.
View 1 Replies
View Related
Feb 17, 2011
I am trying to configure a BEFSX41 router which sits behind a Motorola SB 5120 cable modem. Somehow it now shows DNS entries on the basic setup page. Comcast advises me to zero out all those entries. When I make the attempt a message pops up saying the entry is invalid, and when I close the warning the entry reverts. The router is set to get its IP address automatically from the SB 5120.
View 3 Replies
View Related
Mar 13, 2011
I have been reading posts on this board that state that after upgrading the firmware on a router that you must re-set the router and re-configure your connection. I have just downloaded and installed the latest firmware update for the BEFSX41 (1.52.16.4). When the installation was complete, my network connection dropped out. I then got a "searching for ip address" icon in my notification bar. The connection then completed and my network seems to be running as it should. When I check the set-up screen for the router, it shows the new firmware version. Do I still need to re-set the router? I'm a bit confused by all of this. I have Comcast cable for my isp.
View 2 Replies
View Related
Jul 12, 2007
What the Firewall throughput is for the BEFSX41.
View 9 Replies
View Related
Mar 19, 2011
BEFSX41 Firmware Version to upgrade, version 1 or 2?
I've been using this router since 2006, upgrading the firmware to version 1.52.15 when released in 2007. At that time I think I selected the edition 1 rather than edition 2. Basing decision on the fact that the device had no indication of which model version was correct indicated on the manufacturing labels on the bottom. So I assume edition 1.
Is there any way to tell which hardware release I really have? Maybe by MAC address, or Serial number?
Have not had any problems with the 1.52.15 firmware version, however, I have seen numerous log entries for the following:
2011-03-20 11:45:23 ii=MAX_HTTPSESS2011-03-20 11:45:33 ii=MAX_HTTPSESS2011-03-20 11:45:39 ii=MAX_HTTPSESS
and
2011-03-20 10:53:09 UDP from 202.103.52.147:5060 to nnn.nnn.nnn.nnn : pppp(my ip address & port) followed by 2 to 10 of the following entries:2011-03-20 11:01:33 500 _upnp_Disable
the sending URL indicated as a PRC (Chinese) university with negative traceroute results, nothing really alarming as nothing is getting inside the firewall. Just packets dropped from the senders IP. I am keeping track of the pattern and activity levels.
Will probably just block the whole addy range at the router firewall and PC firewall. AT&T is totally ineffective in blocking this sort of back alley activity.
I've seen only one brief and somewhat dated reference to the "ii=MAX_HTTPSESS" entry and will tackle that issue after updating the firmware to 1.52.16, I haven't found any authenticated tech references for this. I can only make some educated guesses on tweaking HTTP settings.
View 2 Replies
View Related
Jun 6, 2009
I'm trying to upgrade the firmware of a BEFSX41 wired router from version 1.43.3 (apparently the first revision after the original realease) to 1.52.15 (the latest I found), but I can't get it to finish. I'm using a Mac with all the latest versions of OS, Safari, and Firefox. When I use Safari to initiate the upgrade, it get's to the point where it says "Please wait ! Setup will take a few minute _____" and nothing else happens after that, even after waiting 30 minutes or more. When I use Firefox it gets to the same "Please wait" message, then a few minutes later Firefox displays an error message "Connection Interrupted: The connection to the server was reset while the page was loading. The network link was interrupted while negotiating a connection.
View 9 Replies
View Related
Feb 12, 2010
BEFSX41 V2.1
Firmware: 1.52.16
The manual states how to create an inbound traffic policy but if you follow the directions there is no place to select inbound traffic.From the manual: To Create an Inbound Traffic Policy1. Enter a Policy Name in the field provided. SelectInbound Traffic as the Policy Type.2. Enter the IP Address from which you want to block.Select the Protocol: TCP, UDP, or Both. Enter the portnumber or select Any. Enter the IP Address to whichyou want to block.3. Select Deny or Allow as appropriate.4. By selecting the appropriate setting next to Days andTime, choose when the Inbound Traffic will be filtered.5. Lastly, click the Save Settings button to activate thepolicy.When finished making your changes on this tab, click theSave Settings button to save these changes, or click theCancel Changes button to undo your changes.I want to filter out a range of ip addresses from trying to connect to my network.
View 3 Replies
View Related
Jul 30, 2011
I have a BEFSX41 connected to a Motorola SB6120. I changed my plan for a hgih speed, but did not see it.Had a tech out and we found when direct connected to my computer, I get 50 Mbps. When connected through the router, about 9 Mbps. I swapped cables, but still the same.
Is there any way to determine the connection speed on the Internet port? It seems that it only running at 10, when both the router and modem support 100.
View 4 Replies
View Related
Aug 19, 2011
I have a Linksys BEFSX41 wired router. If I wanted to connect a second computer to my router, what would be the maximum length of cable I can use without experiencing any problems ?
View 3 Replies
View Related
Jan 10, 2012
I have the Linksys BEFSX41 wired Firewall router. My ISP is Verizon DSL. The DSL modem is a Westell 6100G. I have the wall phone line connected to my modem. The output of the modem is going to the input of my Linksys router. I have two computers connected to the router outputs. In order for me to see the output or configuration of my Westall modem, I have to go http://192.168.1.1. In order for me to see the configuration of my Linksys router, I have to enter http://10.10.10.1. When I look at the instructions for setting up and configuring my Linksys router, it never mentions the above 10.10.10.1 address, but instead it tells me to enter the 192.168.1.1 address. I have never done this because when I powered both units for the first time, and it worked, I noticed then that my Linksys address was the 10.10.10.1. Why is it then that none of the settings or instructions for the Linksys router never mention to enter the 10.10.10.1 address as oppose to the one the do call out to enter which is the address for the Westell modem? What would happen if both addresses on both devices were the same?
View 2 Replies
View Related
Oct 3, 2012
I have a Dell Latitude D530 - I am only able to,download at a speed of 2.95 while I can upload at nearly 7,My PC that is attached to the same provider will,download at 7.84 and upload at 7.96.
View 7 Replies
View Related
Sep 29, 2011
I set up the e1500 and everything worked well, my download speed over the wifi was something like 50mps, now its down to .3 mps over the wifi. When I'm hardwired to the router the speed goes back up and everything is fine. The only problem is the wifi. Its not the ISP because my roommates aren't having a problem with their wifi at all. I haven't changed anything on my computer except updated some drivers since I set up the router. My network card drivers are up to date and so is the router's drivers. I'm also doing all this about 5 feet away from the router.
I have a Dell XPS L502x running win 7 64 bit.
View 9 Replies
View Related
May 25, 2012
Before 2 - 3 days I bought a PC with wireless lan (RP-WP5122E WL-N PCI-E ADAPTER). I have and laptop, too. My router is Linksys WRT160NL. The laptop have a wireless card with G standart. On speed test makes 14 - 17 Mbps download, which is normal. When I try to download something on my PC maximum speed is 400 - 600 kbps, on speed test is 2 - 4 Mbps. When I connect my PC with cable to my router speed was 10MB/s (80 - 85 Mbps). I try to change channels on wireless network, but there is no change. I downloaded the latest drivers for this WLAN, but the speed is the same. I change the slot on the mainboard and to flash the firmware on my router, but there is no change.
View 1 Replies
View Related
Nov 7, 2011
First this is my setup, i have a 100x100 mb fiber pipe at a location i am working at. i am comming out of a cisco fiber router to ethernet. i am coming straight from the fiber switch to the computer at a 1gb connection. So my problem is when i try to upload to my ftp server via windows explorer i can never get about 1.5mb, but if i upload via command prompt it goes at about 60mb upload, so the pipe is good. So you say why dont you just use the command prompt, well i have specialized gear here that run xp emmbedded and it does this via the windows explorer. I have tried 4 other computers and they all do the same thing. I tried a UDP video stream and worked at over 10mb stream. but all the ftp uploads cap out at 1.5mb.
View 3 Replies
View Related
Jul 12, 2012
I am having difficulty uploading files on the internet because the speeds are so slow. My download speed is 23.88 MBPS, bu upload is .3 mbps. This seems to be a recent problem. The other computers on the network get upload speeds of 5mbps and do not have any problem, so I think there is some problem unique to this computer, and not a network problem. I can't back up my files because the speed is too slow.
View 8 Replies
View Related
Jan 7, 2008
how to block uTorrent on the WRT54G router??? My roommate is killing my internet speed and he already had his last warning so i need to block torrents on my router
View 9 Replies
View Related
Feb 10, 2011
I'm experiencing quite a slow vpn performance. I've tested different scenarios.* Windows XP with built-ín pptp client and Shrew ipsec client* Linux built-in pptp* wireless and wired connections? I never managed to go above 1MBps neither with windows or linux. I managed to go up to 3MBps using the Shrew client.I've also checked mtu settings and everything seems to be fine.
View 1 Replies
View Related
May 20, 2007
Having a problem everytime I try to use load balance on my Rv042 it is slow as a dog and sometimes wont connect at all. if I run in smart backup mode its fine. removed firewall rebooted everything tried numerous configerations upgraded to the latest frimware just about to be convinced
View 2 Replies
View Related
Jan 17, 2011
Very slow transfer speeds problem with this router. When I put the router in the system, my transfer speeds drop from 12 Mbps to 3 Mbps. I've updated the firmware to the latest version but that doesn't work. The most frequent suggestion is to upgrade the firmware which I have already done.
View 5 Replies
View Related
Jun 28, 2012
I upgraded from a E2000 to a EA4500 today and I am experiencing slow wired WAN speeds. On my E2000 I get approximately 60Mbps down and approximately 2Mbps up, and when switching over to the EA4500, I can only manage about 20Mbps down and about 2Mbps up. I can switch back and forth between routers and replicate the results every time
View 7 Replies
View Related
Feb 15, 2013
I have an E1200 acting soley as an AP. Everything works just fine, but when I try to copy files from one wired computer(both Windows 7) to another one on the same router(the E1200 in this case), the network utilization is only about 4%. If I take one of the computers off its wired connection and make it wireless, the utilization goes up to about 50%. Also if I take one of the compuyters off this router, and make a wired connection to my main router(which is connected via a wired connection to the E1200), the network utilization goes up to 50%.
View 3 Replies
View Related
Feb 15, 2012
Set up my new E4200V2 last night, everything appeared to be working but while streaming videos over wired LAN I get short hiccups over wired. While streaming videos, a few second long pause is really, distracting, this is a deal breaker and my previous router (DIR-655) had no issue streaming any videos. The wiring has not changed, only the router.I set up a ping between two wired linux boxes, and get: [code]
Whoa, 10 ms over gigabit LAN. This is crazy, but doesn't tell us much. The 10 ms was one out of hundreds of pings, so its only intermittent. This might explain the hiccups, but this router doesn't appear to log anything, so its hard to say.Next was scp transfers, which never exceed 15MB/s, in either direction. For gigabit, wired LAN this is awful, with my previous DIR-655 I would get at the very least 40 MB/s, in all situations.Next up, iperf. I set up iperf on the two hosts, and iperf reports reasonable gigabit speeds. [code] Tonight I am thinking of reverting to an old firmware, doing a hard reset and seeing if it persists, and if no ideas come up in this forum, it is getting returned, 15MB/s over gigabit lan is terribly broken.
View 5 Replies
View Related
Feb 8, 2011
I am using a Cisco RVS 4000 to test a new 10M/10M internet connection. I'm having a small problem performing the ISP's speed test (speedtest.cavtel.net). The download test consistently gives me 10Mbit/s, full speed for the connection, however the upload speed is usually about 5.5 Mbit/s. My ISP has been onsite and has checked the lines and tested directly, and we have determined that if connected directly we can test to full upload speeds, but when the RVS is connected, we cannot get full speed.
We've tried different cables, reseting to factory defaults, updating firmware, changing port settings, and toggling most of the other setting on the router. Some settings do have a minor effect on the upload speed, but nothing that gets me back up to 10Mbit/s.
I did notice that there appears to be no way to set speed and negotiation settings on the WAN port. Perhaps I am missing it, because that seems like a possible culprit.
Otherwise, the only only thing I can think of is a warranty return to determine if the unit itself is defective.
View 1 Replies
View Related
Dec 6, 2012
I'm having an issue with my new E1200 routeur : I have a 100mbit/s connection and since i installed the E1200 , the speed is cut in half : Max 50 mbit/s .. ( or if this is an hardware limitation ? )
I have a gigabit network card with my pc , everything is fine on the pc / network side as i had these speed fine ( 100mbit/s ) with my old ISP router , ( wich i switched in bridge mode to use the E1200)
View 3 Replies
View Related
Apr 3, 2012
I have a problem with my download speed. I'm supposed to have a speed of 60 MBPS and when I collect my computer direct to the modem I received it but with my e2000 router, the 3 computer connected to it can't reach more than 30 MBPS. I just updated the firmware of the router to the newest version but nothing changed.
View 2 Replies
View Related
May 19, 2012
I have a E3200 Router and when the computers are connected directly to router (Wired) the speed is SLOW and when computers are connected via wireless the speed is fast (normal). What can i do to have the wired computer with same fast speed as wireless?....i'm i missing something?Here are the speed results:
All wired computers connections (total of 4) downwload speed ranging from 8 Mbps to 13 Mbps.
All wireless computer connections download speed stable at 49 Mbps.
View 2 Replies
View Related
Jun 25, 2012
get a new router. but lets give it a try. I read many many post on how to optimize the speed of the router but none worked so far.I got a great wired Internet connexion hitting between 45 to 60 Mbps[URL] the wifi is crazy slow on Iphone, Macbook pro and iPad staying between 3 to 8 Mbps....
I tried to change all of the specs, did the firmware update. is there a perfect configuration with the new firmware ?
View 9 Replies
View Related
Jul 3, 2012
I have a problem with my new router. I connected't my iMac (27" 2010) and NAS Synology 1511. My problem is the slow connection between mac and router - only 100Mbit (ethernet port on mac is 1Gbit), strange thing... my NAS have 1Gbit with no problem, and the mac is not. I trying manual configure - forcing speed to 1Gbit, but then is no connection at all. I'm also trying changing wires, but no change. Im buying special ethernet cable cat 6 - also no change. Changing ports on router - result the same.
View 7 Replies
View Related
Aug 20, 2011
Yesterday, I changed my old belkin n1 router with Linksys WRT54GL router. Ever since them my upstream speed is really slow. I did the speedtest its like .5mbit. My downstream speed is just fine. This issue is only on wired computers, upstream speed on wireless computers is just fine.I retested router & modem several times, my upstream speed is normal when I connect cable directly from modem to my computer.Current Firmware Version is 4.30.14 build 5.
View 1 Replies
View Related
Nov 14, 2012
I'm owner of Cisco RV082 router and I have a problem with firewall setup.I would like to deny internet access on port 80 (all sites) for group of users, and allow them internet access for one site by HTTPS (443)After applying rules internet connection is really slow.. Users have to wait something like a 30 sec for a website..I descovered that the reason for slow internet connection is DENY rule. After disbling DENY rule everything works fine..Now I have a few rules added to firewall:
Priority:1 Action: Deny Service: HTTP(80) Source interface: LAN Source:10.82.0.51-10.82.0.245 Destination: Any
Priority:2 Action: Allow Service: HTTPS(443) Source interface: LAN Source: 10.82.0.51-10.82.0.245 Destination: 80.64.59.42
What's wrong with those firewall settings?
View 1 Replies
View Related
Jun 22, 2011
My newly installed E1200 only sends speeds of about 16 mbps wireless, but sends the ful 60 mpbs when wired. What is going on. Firmware is up to date. Changing the channels didn't do anything. Is there a way to figure out if the problem is with my laptops wireless card.
View 9 Replies
View Related
