Linksys Wired Router :: BEFSX41 Web UI Access?
Feb 4, 2012
I've been struggling to resurrect an older V1 BEFSX41, which suddenly decided to suffer continuous collisions and loss of link. Had been running for several years. I reflashed the firmware with TFTP to 1.52.16.4, and reset for 30 seconds, and re-powered. I am unable to get any response form the web UI. I can ping 192.168.1.1, and obviously push the BIN image to it, but the UI doesn't give any sign of life - not even an error - just blank.
View 1 Replies
ADVERTISEMENT
Feb 17, 2011
I am trying to configure a BEFSX41 router which sits behind a Motorola SB 5120 cable modem. Somehow it now shows DNS entries on the basic setup page. Comcast advises me to zero out all those entries. When I make the attempt a message pops up saying the entry is invalid, and when I close the warning the entry reverts. The router is set to get its IP address automatically from the SB 5120.
View 3 Replies
View Related
Mar 13, 2011
I have been reading posts on this board that state that after upgrading the firmware on a router that you must re-set the router and re-configure your connection. I have just downloaded and installed the latest firmware update for the BEFSX41 (1.52.16.4). When the installation was complete, my network connection dropped out. I then got a "searching for ip address" icon in my notification bar. The connection then completed and my network seems to be running as it should. When I check the set-up screen for the router, it shows the new firmware version. Do I still need to re-set the router? I'm a bit confused by all of this. I have Comcast cable for my isp.
View 2 Replies
View Related
Jul 12, 2007
What the Firewall throughput is for the BEFSX41.
View 9 Replies
View Related
Mar 19, 2011
BEFSX41 Firmware Version to upgrade, version 1 or 2?
I've been using this router since 2006, upgrading the firmware to version 1.52.15 when released in 2007. At that time I think I selected the edition 1 rather than edition 2. Basing decision on the fact that the device had no indication of which model version was correct indicated on the manufacturing labels on the bottom. So I assume edition 1.
Is there any way to tell which hardware release I really have? Maybe by MAC address, or Serial number?
Have not had any problems with the 1.52.15 firmware version, however, I have seen numerous log entries for the following:
2011-03-20 11:45:23 ii=MAX_HTTPSESS2011-03-20 11:45:33 ii=MAX_HTTPSESS2011-03-20 11:45:39 ii=MAX_HTTPSESS
and
2011-03-20 10:53:09 UDP from 202.103.52.147:5060 to nnn.nnn.nnn.nnn : pppp(my ip address & port) followed by 2 to 10 of the following entries:2011-03-20 11:01:33 500 _upnp_Disable
the sending URL indicated as a PRC (Chinese) university with negative traceroute results, nothing really alarming as nothing is getting inside the firewall. Just packets dropped from the senders IP. I am keeping track of the pattern and activity levels.
Will probably just block the whole addy range at the router firewall and PC firewall. AT&T is totally ineffective in blocking this sort of back alley activity.
I've seen only one brief and somewhat dated reference to the "ii=MAX_HTTPSESS" entry and will tackle that issue after updating the firmware to 1.52.16, I haven't found any authenticated tech references for this. I can only make some educated guesses on tweaking HTTP settings.
View 2 Replies
View Related
Jun 6, 2009
I'm trying to upgrade the firmware of a BEFSX41 wired router from version 1.43.3 (apparently the first revision after the original realease) to 1.52.15 (the latest I found), but I can't get it to finish. I'm using a Mac with all the latest versions of OS, Safari, and Firefox. When I use Safari to initiate the upgrade, it get's to the point where it says "Please wait ! Setup will take a few minute _____" and nothing else happens after that, even after waiting 30 minutes or more. When I use Firefox it gets to the same "Please wait" message, then a few minutes later Firefox displays an error message "Connection Interrupted: The connection to the server was reset while the page was loading. The network link was interrupted while negotiating a connection.
View 9 Replies
View Related
Feb 12, 2010
BEFSX41 V2.1
Firmware: 1.52.16
The manual states how to create an inbound traffic policy but if you follow the directions there is no place to select inbound traffic.From the manual: To Create an Inbound Traffic Policy1. Enter a Policy Name in the field provided. SelectInbound Traffic as the Policy Type.2. Enter the IP Address from which you want to block.Select the Protocol: TCP, UDP, or Both. Enter the portnumber or select Any. Enter the IP Address to whichyou want to block.3. Select Deny or Allow as appropriate.4. By selecting the appropriate setting next to Days andTime, choose when the Inbound Traffic will be filtered.5. Lastly, click the Save Settings button to activate thepolicy.When finished making your changes on this tab, click theSave Settings button to save these changes, or click theCancel Changes button to undo your changes.I want to filter out a range of ip addresses from trying to connect to my network.
View 3 Replies
View Related
Dec 30, 2011
I have an issue with slow downloading and uploading on u torrent with my wired router linksys BEFSX41. I thought it may be because I didn't set port forwarding on the specific ports the u torrent use.
But every time When I try to set new port forwarding rules on my router's control panel its asks me for a password and user. Although I know this password and user it will keep asking me about them without saving the new port forwarding settings.
View 1 Replies
View Related
Jul 30, 2011
I have a BEFSX41 connected to a Motorola SB6120. I changed my plan for a hgih speed, but did not see it.Had a tech out and we found when direct connected to my computer, I get 50 Mbps. When connected through the router, about 9 Mbps. I swapped cables, but still the same.
Is there any way to determine the connection speed on the Internet port? It seems that it only running at 10, when both the router and modem support 100.
View 4 Replies
View Related
Aug 19, 2011
I have a Linksys BEFSX41 wired router. If I wanted to connect a second computer to my router, what would be the maximum length of cable I can use without experiencing any problems ?
View 3 Replies
View Related
Jan 10, 2012
I have the Linksys BEFSX41 wired Firewall router. My ISP is Verizon DSL. The DSL modem is a Westell 6100G. I have the wall phone line connected to my modem. The output of the modem is going to the input of my Linksys router. I have two computers connected to the router outputs. In order for me to see the output or configuration of my Westall modem, I have to go http://192.168.1.1. In order for me to see the configuration of my Linksys router, I have to enter http://10.10.10.1. When I look at the instructions for setting up and configuring my Linksys router, it never mentions the above 10.10.10.1 address, but instead it tells me to enter the 192.168.1.1 address. I have never done this because when I powered both units for the first time, and it worked, I noticed then that my Linksys address was the 10.10.10.1. Why is it then that none of the settings or instructions for the Linksys router never mention to enter the 10.10.10.1 address as oppose to the one the do call out to enter which is the address for the Westell modem? What would happen if both addresses on both devices were the same?
View 2 Replies
View Related
Aug 7, 2006
I recently installed a WRT54G wireless router however I has this same question about my BEFSX41 Wired router.
View 9 Replies
View Related
Sep 12, 2011
I have a BEFSR41 V2 router connected to a westell c90 modem and my provider is Bellsouth.net (AT&T). I have the modem set to PPPoE and DHCP enabled. I am using the router as a gateway. The router's status page indicates that is communicating with the modem. Release and renew works and I can detect the addresses of the modem. I just can't pull up websites. I am wondering if this router (12 years old) is not compatable with the service.
View 1 Replies
View Related
Nov 24, 2009
I have a RV042 router and we are trying to set-up our OWA for outside access. I can't figure out which ports or which page those ports are on to open them. We are a small company and we do not have IT except for ourselves. The internal network works fine but i can't get the Exchange access from outside.
View 2 Replies
View Related
Apr 19, 2009
BEFSR81 v3.0.I selecting Enabled UPnP and now I cannot access the router. When I enter the default admin for the password in the Authentication Required screen. I get the following screen: 401 Authorization RequiredThis server could not verify that you are authorized to access. Either you supplied the wrong credentials(e.g., bad password), or your browser doesn't understand how to supply the credentials required.I didn't enter anything new into the username or password fields.
View 5 Replies
View Related
Jan 14, 2011
Have an Actiontec GT704 feeding DSL into a BEFSR41 which is connected to a WRT610N. Can access internet, modem and wired router from desktop. Can access wireless router from laptop. Cannot access internet from laptop or wireless router from desktop. Changed ip address for wireless router to 192.168.2.1 so no conflict with modem or wired router.
View 3 Replies
View Related
Jun 23, 2012
I have configured 2 RV042 VPN with different ISP. Tunnel connected successfully and i can ping each other router but i can access clients which are connected to router. I have added rules also in firewall.
View 1 Replies
View Related
Oct 12, 2011
1. Just got a new DLINK Xtreme N DIR-825 Router. Directly connected this to the internet.
2. Currently, the Linksys WRT54G (1st Generation) is connected to the DLINK by an Ethernet cable to one of the 4 ports on the back.
3. The Linksys further splits the signal to another 2 computers and a NAS by hardwire.
4. The internet is still getting through to all the computers, but the computers are not able to access the NAS or each other.
5. I can't seem to open the WRT54G's access (192.168.1.1) because (I thin) the new DLINK uses a local set of IPs that are 192.168.0.1xx.
I can login to the NAS using its IP, and I can see it on the 'Network Places' of the computers ,but when I try to connect, it says the drive is moved, etc. etc.I use a variety of computers / O.S's on this system: XP (2) hardwired, Win 7 (2) hard wired, Win 7 (1) wireless, Mac OS X Snow Leopard (1) Wireless, plus various other wireless devices (phones,Wii, etc.).
NAS is a Synology DS411+
1) Get logged into my Linksys
2) Get the NAS accepted by other computers on the network.
View 3 Replies
View Related
Apr 4, 2011
We have an RV042 router.I'm looking for a solution where my drop-in clients would have their own WIFI key to access Internet, with no access to our LAN.
-Can I place a Wifi AccessPoint on the DMZ so my drop-in clients use it to connect to the WEB.
-While putting another Wifi AccessPoint on a regular LAN port for Employees to use and stay within the LAN?
View 2 Replies
View Related
Jun 28, 2012
I upgraded from a E2000 to a EA4500 today and I am experiencing slow wired WAN speeds. On my E2000 I get approximately 60Mbps down and approximately 2Mbps up, and when switching over to the EA4500, I can only manage about 20Mbps down and about 2Mbps up. I can switch back and forth between routers and replicate the results every time
View 7 Replies
View Related
Jun 2, 2011
I have a RV042:Firmware Version : v4.0.0.07-tm (Aug 19 2010 19:19:50)PID VID : RV042 V03 .Configured with a internal LAN address (10.0.17.0/24) and ISP PPPoE External address on WAN1.I´ve configured a VPN with a remote location (Fortigate 4) and after the VPN starts up the RV042 cannot ping any machine in their local network (using the diagnostic, all pings failed in 10.0.17.0/24) and no machines in that network can PING and access or manage the RV042
The only way to manage the RV042 after VPN starts UP is using a machine in the other side of the VPN (The Main office)If i force the VPN down, the connectivity begins to work, but as soon the VPN starts up again, the local/LAN connectivity loses again.
View 1 Replies
View Related
Jul 20, 2011
We have an RV042 as main router.We have a netgear WNR2000v2 as WIFI router.We would like to offer our drop-in customers an internet access. But without letting them into our network.
View 1 Replies
View Related
Dec 7, 2011
i have 2 rv042 with a vpn tunnel between them.the problem is that i can't access https over the VPN !if i telnet 192.168.10.1 443 through the VPN, it's not working either. if i telnet 192.168.10.1 443 in my 192.168.10.0 network it's working so it's reall the VPN tunnel the problem.
View 1 Replies
View Related
Mar 10, 2011
I have an RV042 Router and did a one-to-one NAT mapping for my server using an additional external IP I received from byt ISP, pointing to machine 192.168.2.5. I am now successfully able to access the machine via the external IP without issue, however the server is no longer able to ping any external IPs?
the machine has been assigned a static IP of 192.168.2.5 and static DNS servers.
View 1 Replies
View Related
May 31, 2012
I am trying to connect a LAN to the internet via an RVS4000 for remote access to the LAN and cannot connect to the RVS4000. I am using a static WAN address, entered it in the WAN setup area (subnet, gateway, etc.). I do not use DHCP as all the LAN units are static addressed. I rebooted, etc. but cannot see the router externally (I am pinging from a remote site).If I plug my laptop into the WAN cable and set the laptop to the WAN adress, I have no issues. I have checked the cables (all CAT5e shielded), checked both straight through and crossover cables, and have no luck.
View 1 Replies
View Related
Jun 23, 2012
I have configured 2 RV042 VPN with different ISP. Tunnel connected successfully and i can ping each other router but i can't access clients which are connected to router. I have added rules also in firewall.
View 1 Replies
View Related
Jan 22, 2011
My router is a Linksys BEFSR81.Recently I installed a proxy server and now I would like to setup my router so that only the proxyserver (HTTP traffic) can connect to the Internet.
View 3 Replies
View Related
Mar 15, 2011
Does it support SSL VPN? As I would like to have secure web access without installing other software.
View 1 Replies
View Related
Dec 28, 2011
I own a BEFVP41 v2.1. Under "access restrictions" I set days and time when access to internet it is allowed. Also applied "Website Blocking by URL Address" and "Website Blocking by Keyword" however some users are now getting access to the internet. I must also mention this settings: Firewall protection it is enable. Router DHCP it is disable and we use static IP address for the PC´S so I established IP range to apply the restrictions. I also try blocking with MAC address of the PC's.Everything else it has default settings. Internet wire goes first to the router and then to the LAN switch. What am I missing?
View 4 Replies
View Related
Jan 4, 2011
I am using the default configuration at this point. I just connected 1 computer using the default IP with DHCP on the RV042 router. 192.168.1.0/255.255.255.0.I connect my wildblue satalite modem using a static IP address 75.106.203.xxx / 255.255.252.0 I can ping the RV042 router and the static IP address of the wildblue router but I can't ping the gateway on the wildblue side. Either from the PC or the Router diag tools.
View 1 Replies
View Related
Nov 13, 2007
I have a BEFSR41 V2 working as dial in ADSL connection.While I changed my settings of the UPnP in the router I lost access to the admin page. Well most strange is that everything is working.I kept my internet access as well as the computer and printer access.The only thing I lost is access to the router admin page.The password it was not defaulted to admin, neither kept the password that I had set up.
View 9 Replies
View Related
Oct 31, 2011
I have a problem with my Router WRT120N wen I connect to router with wireless are wired it`s not giving me Internet access but the light on the router of Internet is ON if I put the internet cable directed to my computer give me internet.
View 2 Replies
View Related
Jan 4, 2012
I have a Cisco Linksys E2500 modem and I cannot access Zoneminder which is essentially a Linux Security video DVR software package. It is running on a Ubuntu Linux server.
I have HTTP port 80 forwarded to the the static IP address of the Ubuntu server but I repeatedly get a error indicating that the connection timed out whenever I try to access Zoneminder remotely as in remotely accessing it from a coffee shop.
I have absolutely no problem accessing Zoneminder when I on my home local LAN.
I can access other software from remote locations on port 4369 with a TCP preferred protocol setting. That is, port 4369 is forwarded to another Windows workstation with an assigned static IP address. Absolutely no problems with port forwarding of 4369.
Also, I've tested port 80 on the YouGetSignal website which is used for testing port forwarding. The website indicates that port 80 is closed. But when I test port 4369, the website reports that the port is open. Zoneminder which uses port 80 is fully operational when I test port 80 via YouGetsignal.
My ISP has told me that they do not block any ports including port 80.
View 7 Replies
View Related
