I have a Linksys WPC54GS Wireless adapter with Speedbooster (hardware version 1.1) & I lost my installation CD. I just installed a fresh copy of Windows XP Home Service Pack 1 and I am using a Dell Latitude C810 laptop. The card is the PCMCIA model. I cant get any assistane from Linksys because my warranty expired and I dont have the funds to buy a new card right now, so how I could get this one working again?
View 2 RepliesI had this card working on this notebook with Windows XP, but with only 256mb ram it ran too slow. So I went back to 2000 on it. But I can't get the card to work, I've tried using the setup, the link light on the card does flash on and off. But in the linksys program just says no association with access point and says WPC54GS is inactive. I tried just installing the driver when it detects it but that didn't work. Also I try to start the wireless configuration and just get error 1747 the authentication service is unknown. What do I need to do to get the card working on here so I have internet access?
View 5 Replies View RelatedWe bought an Wireless-G Notebook Adapter with SpeedBooster (WPC54GS: [URL] for an laptop ( HP Pavilion dv6137eu : [URL] for my sister. at the specifications of the laptop, it tells me (translated): Pc card slots: 1 ExpressCard/54 slot (also supporting ExpressCard/34) first question: is that slot the right one, fitting the cisco wpc54gs?
if we bought the right thing, whats wrong then? : The problem is, she installed everything like how its told in steps 1a-g of: steps [URL] then she plugged in restarted like the next step told. even after a new restart, the laptop seems to not recognise the card. even the power light isn't light up. Is the power light only light up when its also installed and recogised by the computer? or does it have to light up from the moment its connected to the slot? we couldn't also find it at the device manager:
the network adapters we found are, i think, the build in ones. at what folder at the hardware tree had the card in de bus has to appear? i dont know what the only device thats not recognised here, must be, but we cant install it with the cdrom of the cisco card, so i dont thing it is the cisco card?
I just installed windows xp pro 64bit and i am not able to use it im guessing because i need the correct driver, ive tried looking around but couldnt find anything. I also try it working with Windows 7 ultimate (64bit) and i could not get it working on that either.
View 4 Replies View RelatedI've been using my AE1000 for about a month now with absolutely no problems. Yesterday it just stopped working, I removed it from the USB port and just about burned my fingers on the metal part that plugs into the USB port. BTW I am on Windows 7 64-bit.
Now it won't work. I've tried reinstalling the driver and the device just blinks in the "Devices and Printers" control panel. I removed it again and it was very hot to the touch after only being in the port for about a minute.
Ive been using my linksys wusb54g network adapter for a while. I have windows vista and until today it has been working fine. I reinstalled my OS because i had been having blue screen of death problems. Now that i've done this, i cant seem to get my adapter to work againIve seen a bunch of sites saying i need to install ralink rt2500usb or something, but the links for it never work as these pages are several years old.I cant figure this out. All i need to do is get my internet working and this adapter just doesnt work. Theres no support for vista i guess.
View 9 Replies View RelatedWhen I insert the disc for my new AE1000, the setup opens automatically and begins to run. Before even letting me read the software end user license agreement, I get a screen that says the following: "Our Customer Support team can assist.Your Linksys Adapter was not successfully set up."I can not figure out any way to keep this message from showing up.
View 4 Replies View RelatedI have tried to install a usb network adapter wusb100 ver.2 under win7 x64 and win7 x64 sp1(two different machines). I have installed and downloaded the latest drivers ( Driver11/09/2009 Ver.3.0.3.0 (64-bit)). Device manager reports everything is fine, but i can't find the adapter anywhere in the Network and Sharing Center on both machines, not even if i run ipconfig it won't show up. As a result of course there is no wireless connection available. Although adapter has worked fine when tested under win7 x32. But win7 x32 is not my case.
View 1 Replies View RelatedI am trying to connect a linksys adapter AE 1000 in my XP SP3 but during the CD-instalation appears that error:
AppName: setup.exe
AppVer: 1.1.10049.0
ModName: kernel32.dll
ModVer: 5.1.2600.3541
Offset: 00012a6b
And then a microsoft error windows shut down the installation.
I got the D-Link router setup and with the network key. When i tried to type the network key in my pc(which has the adapter). it gave me an error.Network key password need to be 40 bits or 104 bit depend on network configuration. This can be 5 or 13 ascii characters or 10 or 26 hexadecimal characters". what does it mean? because the network key work with other pc..but not my pc with WMP 54G. reason?
View 3 Replies View RelatedJust got a new router. All of my devices connect fine to it except for the desktop that is using an external Linksys wireless adapter (WUSB54AG).The desktop is running Windows XP (Home Edition) SP3.The latest driver for the adapter has been installed (3.0.18.0).I am able to connect if security on the router is turned OFF.The router has 3 security options:
1) WPA-PSK (TKIP)
2) WPA2-PSK (AES)
3) WPA-PSk (TKIP) + WPA2-PSK (AES)
My understanding (from Linksys tech support) is that the device SHOULD be able to connect using WPA-PSK (TKIP). My Linksys Monitor indicates that the device is connected to the access point but not the internet (when I used WPA-PSK (TKIP). The IP address that is assigned is 169.254.3.129 and not the expected 192.168.1.x.When I turn security OFF on the router, the device can connect and I am assigned a "good" IP address (192.168.1.x).
I have 2 pc, one with windows xp SP3, and one with Ubuntu 10.04 Until 1 month ago on ubuntu it worked via a patch founded online, from 1 month on ubuntu it doesn't work anymore. Before I used a cable for xp and wireless for Ubuntu. Now I use cable for ubuntu and I try with key usb on windows xp sp3, but doesn't work, I see led, System says that connected, but If I do ping to a site via dos terminal it doesn't work. It doesn't work also if I use internet explorer to see google, but system says connected via linksys.
So I need to solve issue with windows xp, then I hope to solve also for Ubuntu.
My AE1000 has worked for about 2 weeks, but just stopped working. Have tried to reinstall but it won't recognize the adapter. I can't click the "next" button to continue the installation. I have chagned the USB ports and restarted the computer. But it still wont install. I have Windows Vista. I also have Norton, do I need to uninstall this?
View 1 Replies View RelatedAll Installed my AE1000 this evening, after two go`s got it to work BUT the Cisco installer comes up with "Our customer support team can assist Your Linksys Adapter was not successfully setup." but it is working .. I never got the screen with the four "bubbles" (as per the instructions here on the Cisco website)
PS Running Win7 with AVG security
I have a E2500 router and just got this AE3000 adapter. Thought that would bump up the wireless signal for using my laptop at the other end of the house about 75 feet from the router. The new E2500 Wireless N has been a big improvement. The AE3000 installed perfectly and shows up as working properly. It's just that the signal strength on my laptop shows 2 bars and the signal strength for the adapter shows 2 bars.
View 2 Replies View RelatedI've had the AE2500 adapter for a few weeks now, and it's worked fine up to this point. When I started up my computer today, however, it wouldn't connect to the network. I've uninstalled the software that came with the adapter and I've tried to reinstall it. However, when I got to the installation step to insert the adapter, the computer would not identify the AE2500. I've tried updating the drivers through the device manager, but I received an error stating that "a device attached to the system is not functioning".
View 6 Replies View RelatedIt used to work, but just stopped. We have tried to reeinstall but it won't recognize the adapter. I cant click the next button to continue installation. I have changed USB ports and restarted the computer. I have unstalled Norton 360. But it still won't install.
View 3 Replies View RelatedI recently purchased the WET610N Wireless Bridge to use with my Samsung BD-P1590 Blu-Ray Player. The player has a few built in apps that include Netflix, Bockbuster, Pandora and YouTube. I successfully setup the bridge and hooked it up to the blu-ray player. It wasn't that hard. All the internet apps on the player work fine except Netflix. The first time I use the netfix app, it is supposed to give me a code that I use to register the device with netflix. However, I get a message that Netflix is temporarily unavailable. I have called netflix and they assure me that this is not the case and that it is most likely my wireless setup. The troubleshooting on Samsungs website points to the same thing. With that said, I disconnected the player from the wireless bridge and wired it directly to my router. Netflix works just fine then. Below is a list of things I have attempted:Disable the firewall on the router to see if it was blocking the app. (had the same results)Checked my firmware on all my devices (they are all current)Powered down all my devices and started them up back up starting with my DSL modem and ending with he blu-ray player (same results)Configured the bridge and player to use a static IP vs using the IPs automatically assigned by the router. (same results)Disabled aggregation on all WMM categories. I don't think the WRV54G router supports aggregation,, so I though this might cause a conflict with my setup. (same results)Enabled the broadcasting of SSID (same results)Chatted with linksys support. They basically checked to see if I had the latest firmware and that the bridge was working. They then recommended that I exchange the bridge for a new one. (I have not exchanged it for a new one yet, just because I am not convinced that there isn't something else wrong with my setup)My Configuration
DSL Modem --> WRV54G Linksys Wireless Router --> WET54G Wirelss Bredge --> Samsung BD-P1590 Blu-Ray Player
Router is broadcasting in Wireless G only on channel 1
Using WAP-PSK encryption
I am not sure if the problem lies with the routewr or the bridge. I am hoping someone out there can confirm that the WET610N truly does work whne using it with a BD-P1590 blu-ray player. This would lead me to believe that there is something wrong with my configuration or with using it combination with my older router. I would like to note also, that I have had one instance where BD Live didn't work. However, it has worked on other disks.
This PC I am on refuses to work with USB wireless adapters of any shape or size. I have currently tried using 3 Belkin USB wireless adapters, both for 802.11g and 802.11n. I know there is no issue with the USB adapters as I have tried these in a friends computer of EXACTLY the same version of Windows 7 (64 bit Professional). I have tried simple changes, such as switching off Anti Virus and Firewall settings. I have also tried updating drivers, going through setups multiple times, restarting my PC more times than I care to count.The problem I am now facing is that the USB Wireless Adapter seems to be installed, according to the Adapter List in Device Manager, which is showing no Yellow Triangles in any lists, all seems fine there. No connections can be found, and it cannot be the range, as I am currently sitting in a built up area housing multiple connections that can be found from the same spot as where my PC is.
I am currently using a Belkin USB Wireless Micro Adapter Surf N150 ( url...), and I know that the USB adapter aforementioned is in no state of malfunction, as having used it on different machine.Using a Gigabyte M68MT-S2 motherboard and have had not USB troubles until now. I have never tried configuring my PC for wireless setup previous due to always having been able to connect through a wired connection up until now.
I am having problems with any type of Network Card or Network USB adapter working with my PC running Windows 7. I had a LinkSys WMP54G PCI card working on this computer about a year ago as I was needing to use a wireless connection but then I didn't use it for 6 months. When I went to use it again, it wouldn't pick up connections at all.Thinking it was an issue with the card, I picked up a Edimax 7612UAn USB adapter thinking it should work out of the box. When I plug the USB adapter in, the standard Windows driver installation tries to run but an error message occurs stating "Device driver software was not successfully installed" accompanied by "Realtek RTL8191SU Wireless LAN 802.11n USB Failed". If I try to install the drivers manually, nothing changes and in Device Manager the following error message is displayed under Device Status "This device is not working properly because Windows cannot load the drivers required for this device. (Code 31)".
View 3 Replies View RelatedI am having problems with any type of Network Card or Network USB adapter working with my PC running Windows 7. I had a LinkSys WMP54G PCI card working on this computer about a year ago as I was needing to use a wireless connection but then I didn't use it for 6 months. When I went to use it again, it wouldn't pick up connections at all. Thinking it was an issue with the card, I picked up a Edimax 7612UAn USB adapter thinking it should work out of the box. When I plug the USB adapter in, the standard Windows driver installation tries to run but an error message occurs stating "Device driver software was not successfully installed" accompanied by "Realtek RTL8191SU Wireless LAN 802.11n USB Failed". If I try to install the drivers manually, nothing changes and in Device Manager the following error message is displayed under Device Status "This device is not working properly because Windows cannot load the drivers required for this device. (Code 31)".
View 1 Replies View RelatedMy usb devices- whenever I plug my Belkin usb internet adapter in I get an error noise (3 beeps) and the device does not power on. I tried another one (Cisco) from a different PC and got the same error. Tried this on all the ports and updated the drivers. All other USB devices work fine, tethering my phone to get internet for now. Had been using the device without problems for months until getting the error. The error started occurring when I unplugged it and plugged it back in. Using Windows 7 x64 on an HP Pavilion.
View 1 Replies View RelatedJust finally updated my ancient belkin modem to a Netgear D3600WiFi modem router which works really well. However. I have a old G5 Mac without wireless so have always connected through my old belkin modem with Powerline adapters over my house wiring circuit:confused. Unfortunately the powerline adapters no longer work although both lights are flickering on the units. Netgear say they should work.
View 1 Replies View Relatedmaking Windows 7 do what it's supposed to? Seriously, there needs to be a button you can click to roll it completely back to XP.
View 1 Replies View RelatedWhen I get to the screen that asks for the the security password, and after typing in password then at the bottom their is a button for Back and one for Cancel. The button in the middle for Next is not highlited or clickable.
View 2 Replies View RelatedHow to install model WUSB54GSC.
View 5 Replies View RelatedI run the CD setup disk and the driver install correctly.In the "Connecting the Adapter" screen I click next before connecting the adapter,the setup screen just close with out any notification and no icons on the system tray.I shut down the machine, insert the adapter and power on the machine,now I have the monitor icon and a wireless connection icon in the system tray (the Power led is green and the Link led isblink),when I double click on the monitor icon I got the following screen: no available wireless and the refresh, connect and manual setup are disabled.when I click on the "open the monitor" form the right click menu I got the following screen: also nothing to do on this screen.so I think it's was because I don't have any wi-fi around me, I shutdown the computer raise my wi-fi andrestart the machine, now the led in the same status but the system tray icons didn't appears and when Itry to open it from the menu it's run for few seconds without any screen and disappear.
View 6 Replies View RelatedI'm running Windows 7-64 bit. The AE1000 works great so far, in the one day I've had it, and it appears to start itself and connect when turning the computer on (unlike other people on here that I've seen). BUT, it's all pointless if I can't put my computer into standby. The adapter kicks it right back out as soon as I try to sleep the computer.
I've checked the device settings and "allow the device to wake the computer" is unchecked (in fact, it's grayed out). I rarely turn off the computer; I much prefer to just put it in standby. I don't want to have to unplug the adapter every time I do that.
I recently re-installed Windows on my PC, and I had the Wireless-G PCI Adapter installed before I done the re-installation.Now I've re-installed Windows, the adapter doesn't work. Do I have to re-do the whole process again? Also, I didn't actually install it myself, so any detailed step-by-step tutorial?
View 3 Replies View RelatedI'm at a new apt and I can't get Online with vista to download the driver so I've been trying to download it on a droid or iPhone and transfer the file any know any way to do this besides finding a cd? Can I make a cd at a friends house by downloading the driver online? Where can I get the driver?
View 1 Replies View RelatedI picked up a AE3000 for an older laptop, but it will not connect to any network. It is on an older (01') dell laptop running XP SP3. I have tried using the disk and downloading the latest drivers on-line but no luck. It picks up all the networks around me and mine, but it says trying to connect and just can't. I tried it on another laptop and everything works fine. Is there an issue with this adapter and the original USB ports or XP in general? I have checked and rechecked the passcodes, I have deleted all of the profiles and started from the beginning again. I removed my anti-virus program as well as the last effort. Nothing I do seems to make a difference though.This is just used to access the internet on a laptop that is dedicated to a telescope.
View 4 Replies View Relatedi tried down loading drivers but computer still says needs cd.
View 4 Replies View RelatedLike I said my AE1200 adapter keeps disconnecting, it happens about twice a day, underload especially.I already tried to update drivers, reinstall drivers, tweak settings, nothing works, I even turned off power save mode.I'm running WIndows 7 64-bit
View 4 Replies View Related