I can connect to skype but i can't browse anything in the internet. I'm using a CISCO WRT54G2 wireless broadband router.I cannot ping also but im online in skype or chatting application.
View 5 RepliesI have this router back in my home office for my wife's Mac laptop. I recently purchased a new Sony TV with internet access capability and was hoping to gain access through my router, however during set-up attempt it will not connect. My wife is able to use her laptop in the same area as the TV.
View 3 Replies View RelatedWhen I connect the ethernet directly to my mac the internet works fine, but when I try to connect through my Linksys WRT54G2 V1 Wireless-G Broadband Router I can't connect to the internet. Omitting a few minor problems, my router has been working fine for the past year and a half. Recently it started giving me trouble so i have started trying a number of things to fix it, but I'm no expert in this category. The other day i tried updating the firmware which actually worked for a couple of hours, but then stopped working again.
View 3 Replies View RelatedBeen trying to connect to the internet through the modem with ethernet cabe and it repeatedly does not connect. I've set up teh router with the linksys setup program and still nothing.
View 1 Replies View Relatedrecently my internet got disconnected, they reconnected my internet configured my modem when i tried to connect my router ,it would connect to my comp but it said there was no internet. I reset it to factory settings via ip address and then threw the button on the router when i installed software it keeps saying that the router cannot recognize the internet and i should contact my internet provider, but my internet is working when i connect it to the comp directly?
View 4 Replies View RelatedI have a WRT54G2 router and when I try to connect to the internet, both wired and wirelessly, my network icon gives me a "No Internet Access" yellow sign icon. I have successfully connected to the internet by directly connecting to the modem and I have connected to other wireless networks using this computer so I have pretty much narrowed the problem down to the router. I have already perform a firmware upgrade to the latest version and did a hard reset of the router and setting it back up, to no avail. One problem I ran into while I was setting up though was that I can't even set it up with the WiFi-protected setup so I had to set up the password and stuff manually, as I have always done successfully in the past. I've never had a problem with this router in the past and so I think this router may be due for a replacement. I have contacted support through live chat and all the options they're giving me is either pay $25 to talk to someone about this or go through troubleshoot section.
View 2 Replies View RelatedI have A a linksys WRT54G2 and am trying to connect it to my wii. I had my Wii search for an access point And it found my router. I put in my password and it was accepted but I am still Not Connected to the internet.
View 3 Replies View Relatedi have a WRT54G2 and i have it plugged in. i want to avoid downloading things but i had this thing working a month ago, it says its connected but no internet connection.
View 3 Replies View RelatedMy computers will not connect through to the internet. It's not the modem, because if I connect my desktop directly to the modem, it connects fine (which is how I'm typing this now), but if I plug in the router, my desktop and my laptop (wireless) will show they're connected to the network, but that there is no internet connection available. Support won't troubleshoot because I've had my router 1 year and 10 days (which I think is a crock of **bleep**) and the "Guide Me" thing is just running me around in circles. I'm so pissed off I'm about to throw the router through a window and buy another (*NON*-Linksys) router, rather than pay $30 for one time tech support (which, with my luck, the same thing would happen again in 3 months, and the same directions wouldn't work then). I've done a factory reset, and set up the router from scratch, done a firmware upgrade, everything, but it still won't connect
View 1 Replies View RelatedI recently purchased one simply because we needed a wireless router with my roommate using a new laptop. Installation went by without a hitch but when it came to actually using the internet, it was so sluggish that it was impossible to use, on either computer. In fact, I had to disconnect the router and go directly from the modem to even make this post.
I've upgraded the firmware and I thought it was fixed because the internet seemed to be moving at a decent pace (loading pages, speed tests), but then it went back to moving incredibly slow if not timing out altogether. There was a problem with random disconnects but that was something that the firmware upgrade did seem to fix outright.
I recently purchased one simply because we needed a wireless router with my roommate using a new laptop. Installation went by without a hitch but when it came to actually using the internet, it was so sluggish that it was impossible to use, on either computer. In fact, I had to disconnect the router and go directly from the modem to even make this post.
I've upgraded the firmware and I thought it was fixed because the internet seemed to be moving at a decent pace (loading pages, speed tests), but then it went back to moving incredibly slow if not timing out altogether. There was a problem with random disconnects but that was something that the firmware upgrade did seem to fix outright.
Lose internet connection at least once a day. Each time regaining by unplugging power cord for approx. 10-12 seconds. Is this a router failure and maybe needs replacing or ?
View 2 Replies View RelatedMy PC will connect just fine, but it is the only device on my network that the router will allow internet access. The router will allow other devices (DVR, laptop, nook) to connect to it, but won't allow those devices to connect to the internet. Each device will show the same error, - "connected to linksys - no internet". I've reset the router many times with no results.
View 1 Replies View Relatedmy router's wifi has no internet access tried hard reset and firmware upgrade. but i can used it when i connect my laptop on the lan ports.
View 3 Replies View RelatedI'm trying to configure my Linksys WRT54G2 router as my primary router and have my Actiontec just used for the my FIOS TV (eg VOD, widgets, guide). I've googled many HOWTO's on how to do this but I just cant get it working. So setup up will look like this in th end:
(DHCP Server)
(Wireless) (Only TV)
Internet >> WRT54G2 >>> Actiontec >>> PC/Laptops
|
FIOS TV -------------
how to set this up? I understand that the STB devices configured on my Actiontec routers is actually my TV receiver and currently configured with the following IP addresses:
IP-STB1:Connection Type: Coax
192.168.1.100
IP-STB2:Connection Type: Coax
192.168.1.101
IP-STB3:Connection Type: Coax
192.168.1.103
I have COAX Ethernet setup so everything is going through ethernet per Verizon phone tech.
Actiontec Firmware Version: 4.0.16.1.56.0.10.11.6
WRT54G2 = DDWRT firmware
I've tried the following HOWTO's to no avail.[URL]
My WRT54G2 v1 does not automatically connect to the internet on computer start-up. The computer will say "Connected, No Internet Access" In order to fix it I have to unplug the router and then plug it back in. This happens to any computer that tries to get online from a cold start-up. The router must always be unplugged, then plugged back in, then it will have internet access (and will generally maintain it throughout the session and even if the computer is restarted, i.e. warm boot). I have downloaded the latest firmware uprade.
View 9 Replies View RelatedI have a very annoying problem with my Linksys WRT54G2.When I connect a wireless device (laptop, phone, TV, Ipad) to my wireless network I only see a Local connection, no connection to internet. After resetting the router (power off for several seconds) the internet-connection is available again.I have to do this every 1 - 2 days.
View 7 Replies View RelatedSo I've had this problem before and normally I solve it by simply unplugging everything from my modem and router but ive tried that this time several times to no avail. The internet suddenly cut out one day and when I did my usual unplugging thing it came back unbearably slow.Right now I'm running off a motorola SB5100 Surboard modem and a linksys WRT54G2 router and its not my computer, everyone in the house is getting terrible speed.
View 10 Replies View RelatedI have a Linksys WRT54G2 V1and I am trying to hook it up to my broadband modem after hooking up the connections it still does not recognize?
View 2 Replies View RelatedYesterday my wireless internet suddenly stopped working. I plugged the ethernet cable directly from the modem to the computer and everything was fine, so I reset the router, reconnected it to the modem, and went to the setup page 192.168.1.1. I reconfigured the router on the setup page, leaving all previous settings the same (except I renamed the network from linksys to our own name and reconfirmed the WPA Personal password). My computer can connect to the wireless network but I can't go online.
View 9 Replies View RelatedReally not grab Router Gateway, even as did the 30-30-30 reset because I had all the lights on, and is still in trouble. I am currently connected via ethernet to the router only. And yet not grab us Links Home door. The lights now are Power, WIFI and Port 4.
View 2 Replies View RelatedI have a WRT54G2 v1 (no new firmware available) with a cable-modem connection (Motorola Surfboard), every thing works perfect but when my ISP goes down and then back up I cannot get the router work, LAN or Wifi connection. I have ping response to the router and I'm also able to get into the admin page. The only way to recover is restarting the router and sometimes releasing DHCP and then Renewing it, and the Wan connection actually gets the same IP it had before.
View 3 Replies View RelatedI'm not really computer savy and I have an old wireless G Broadband router model # WRT54G2 V1 .
View 1 Replies View RelatedWent away on vacation for a couple of weeks and when I got back my Linksys WRT54G2 has lost it's configuration. It's showing a WiFi signal, but is no longer password protected.
I've tried connecting with a desktop on the same network, to 192.168.1.11, but that address is not connecting. I tried to reach it with my iPad wirelessly, and it's giving me the login screen, but not allowing me to login. I tried to use the reset button on the back to reset it to the factory default, but then I should be able to login with no username and the password of "admin", correct? But that's not getting me in either.
I'd like to get this network password protected again and not offer a signal to all of my neighbors.
I've tried to connect my father's laptop and my father's girlfriend's daughter's PC to my Linksys Wireless Router, model #WRT54G2 V1. So far, I have steady and fast internet access on my PC which so far I've only gotten my father's laptop to connect through. However, I can't figure out how to get her PC to get internet access through my router. I'm mediocre at configuring computers, and I'm absolutely terrible at routers. :/ There was the possibility that her computer isn't new or advanced enough or whatever to be compatible with a wireless router, but at the same time she has a Wireless Network Setup Wizard app. in the control panel area, so wouldn't I be correct in assuming that if a computer has a wizard dedicated to it, it is compatible? I've run Wireless Network Setup Wizard as well as just plain Network Setup Wizard, and I've had them both read that it was successful connecting to my Router's network...but where do I go from there? I've never had to mess with a PC before so I'm not entirely sure. She has a modem, which can not be plugged into the phone jack at the same time as my modem otherwise we both do not have internet access, however if one of us plugs in that person is fine, so that's when I figured I'd try to get her PC into my network with my dad's laptop. Also, we have a Broadband connection setup through Verizon, if that matters at all. Does she need a modem to hook up to my network at all? If so, does that modem need to be plugged into the phone jack? If required I'll give her OS and PC specs and such, but from what I know just being on her computer she runs Windows XP as an OS and her computer is an "eMachine".
View 9 Replies View RelatedI have been having trouble with my wireless router for the past month and not sure what is up with it. I have recently moved and got it working for a day then the wireless did not work and i was not able to access the setup webpage either. What I ended up doing was upgrade the firmware to the newest one and it worked well for about 2 weeks but then started again and the only way it works is to reboot the router but then the next day it will not work.
View 3 Replies View RelatedI upgraded to v1.0.0.4 because on v1.0.0.1 all of a sudden my router's internet connection to my wifi devices was 'becoming stale' and I would lose internet connectivity even though i was still connected to the router. The only way to get my router to get the browser to load pages again was to go to Status and release then renew dhcp.
After upgrading, it does it less often. The problem now is that when my devices detect the network, they are all forced to re-enter the password. Well, all iOS devices. My macbook air doesnt require me to re-enter the password but it does not automatically connect to the network even though it is set up to do so and does so with 3 other networks from offices and other houses.
In other words, my only problem is with my wrt54g2 at home. My iOS devices must be told everytime to connect to that network (they wont connect automatically) and the password must be re-entered everytime. This only happens with this router. And my macbook air has to be told to reconnect to this network although it DOES save the password for it.
What could be the problem? I already changed the patch cable from my modem to my router. That didnt do much.
i want to set up a security password for my ciscoWRT54G2 V1.5, but when i go to the setup page click on wireless security and choose WEP it says disabled over and over again..
View 5 Replies View RelatedI've design a network with wrt54g2 router, and I'm configured with IDIRECT MODEM and its providing dhcp and it's working properly. But I want to provide static IP to my clients.
View 9 Replies View RelatedI bought a Linksys-Cisco wireless G Broadband Router model # WRT54G2 some time ago, and I never installed it. Now I cannot find the set up CD-ROM or the user guide CD-ROM. Is there a way to down load these from the product site...
View 9 Replies View RelatedI installed a Linksys WRT54G2 router earlier this year and set my Siemens modem from AT&T(Actually from SBC before the two merged) in bridge mode. I did this so I could change the NAT setting on our internet, which was interfering with my Xbox. It worked for about 4 or 5 months with little to no problems. Recently, however, the internet has been disconnecting and when I check the status page on the router it says it is disconnected. Sometimes clicking on the connect button will work, but usually it will say "Connecting" and keep refreshing the page for a little while without any change, then give me a message saying it couldn't get the IP from the PPPoe server. Turning it and the Siemens modem on and off and fiddling around seems to solve the problem, but only temporarily. Interestingly enough, I don't think it ever interferes with my Xbox. Until recently, the Xbox was set as the highest priority on the QoS page, but I changed the computer to the highest priority and it hasn't worked. In addition, the small, thin green light bar just below the Linksys logo on the top of the router has just recently started changing to orange occasionally
View 9 Replies View RelatedI am trying to password protect my router but when I go into wireless> security mode and click on WPA or any of the other choices it goes back to disabled.
View 3 Replies View RelatedA couple of days ago I noticed my download speed (from my own webserver) has slowed down. I checked my wireless connection and saw that the radiotype was now 802.11g instead of 802.11n, what is always has been. I looked at the Wireless configuration in the router's webbased config panel, but the only things listed there are "Disabled", "Mixed", "Wireless-G Only" and "Wireless-B Only". A scratched my head a bit, wondering wether or not I really bought an N router or just a G router. But IIRC I really bought an N router. It said so on the bill. Also, when I check the user manual, page 14 says I should be able to select "Wireless-N Only".
View 5 Replies View Related