Linksys Wireless Router :: Print From Living Room Desktop Using WRT120N?
Nov 23, 2011
At home, I have two desktops (bedroom and living room), a bedroom printer, and a WRT120N router. The bedroom desktop is connected to the WRT120N route and the printer is connected to the bedroom desktop. The living room desktop is connected to the WRT120N route. I can print from the bedroom desktop, but cannot figure out how to print from the living room desktop.
How can I print on the bedroom printer from the living room desktop?
View 5 Replies
ADVERTISEMENT
Aug 25, 2011
At home I am using the linksys wireless bridge WET610N to stream media to my livingroom. The setup looks like server <-> Linksys E4200 <-> WET610N. If I connect my laptop to the WET610N i get a speed close to 100Mbit/s. With this speed I can easily view HD movies, by playing them on my laptop. So far so good...But if I instead connect my Popcorn Hour A-100 (a media player) , to the WET610N (instead of the laptop) I get really poor performance. just a few Mbit/s, which is not enough.So my question is, why is the following setup working fine:server <-> Linksys E4200 <-> WET610N <-> LaptopWhen at the same time the following setup is working poorly:server <-> Linksys E4200 <-> WET610N <-> Popcorn HourThe WLAN connection between the Linksys E4200 and Linksys WET610N seems to be fine. The problem I am having seems to be the Ethernet connection/setup between the WET610N and the Popcorn Hour media player.
View 1 Replies
View Related
Dec 26, 2012
I just installed an older router (WRT120N). Purchased an adapter for desktop and wireless connection for destktop works. Cannot get other devices to use the wifi (iphone, ipod, android phone...). I am at a loss. Saw some suggestions about disabling a Upn or something under the router's LAN properties
View 1 Replies
View Related
Aug 23, 2011
I have time warner cable as my ISP, and have a netgear wireless modem hooked up to the only computer in house, in my living room, but I would like to have internet access in my room as well (where my rig will be). What do I need to get? I was thinking of getting a wireless network adapter PCI card, but am a bit concerned that I will then have to deal with laggy connections while online gaming.
View 3 Replies
View Related
Jan 28, 2011
I have a home PC Windows 7 desktop and a Linksys WRT120N wireless router for another computer currently. I need to add a VPN and a desktop work computer (XP) to the above.
View 2 Replies
View Related
Dec 25, 2011
So my family has an E2000 setup near the modem in a room that litterally is a DEADZONE, signal bearly gets in or out of this room. I've argued until I was blue in the face that we ned to rewire the internets inlet to the house in to another room that isn't a deadzone and rune a router from there.They IT disadvantaged refused. We have also an E2500 they say hook it up, maybe it will work better (when your in a concrete and mettal room with a router sitting on a shelf surrounded by book and with a corless phone system hooks up and sitting on top of it... its jsut not going to work. is there a way i can take the E2500 and make it an access point for the E2000?
I figure if I can I would take the E2500 and put int in a better location and jsut have it relay the E2000 internet. Because of the IT limited thought process of most of the people living here I'd prefer that they share the same SSID or atleast make for a simple transition for the apes I live with.
View 6 Replies
View Related
Jan 26, 2011
How do I set up the linksys wtr54G wireless router in the dorm room. When I try setting it up, I can only access the router set-up main page which is 192.168.1.1 then icon status shows that it sends out packets, but my computer doesn't receive any signal or (bytes). So, could it be that there are university restrictions on routers/dorm-room internet? How can I get it to work? I heard I need to set up an access point.
View 1 Replies
View Related
May 7, 2012
What signal strength should I expect when in the same room as the e4200 ?I'm checking signal strength with iStumbler and with option-right click on airport menu icon on my Mac.I'm getting a signal strength of about -55 while in the room with the router.What signal strength should I expect while in the same room, no physical obstructions, etc. ?
View 6 Replies
View Related
May 10, 2011
can i print from a xp desktop through a linux desktop
View 1 Replies
View Related
May 18, 2011
I have a laser printer that's connected to a desktop running Win 7. The printer is set to SHARE. I got a laptop that I want to print from through the desktop. Is this possible? The printer is not wireless and I don't have a print server. I have wireless network running on my Linksys router, but the desktop and the printer are not on it.I have the desktop and laptop on the same WORKGROUP, but when I try to add the printer on the laptop by selecting a NETWORKED PRINTER option, I get an error.
View 2 Replies
View Related
Jan 24, 2012
I just picked up the E3200 and love it. This morning I hooked up my printer via the USB. Everything went smooth until I tried to print something. I thought nothing was happening, but I let it sit for a while. While I was waiting, I was messing around with my network setting in windows. I realized that my network had been set to 'work' for some reason, so I changed it to 'home'. As soon as I did, my printer spit out my test page. (probably 5 min after sending the doc.) I don't know if it was just coincidence or what, so I sent another page and nothing happened (yet).
Is this common to take that long? Is there a way to speed this up?
View 3 Replies
View Related
Aug 5, 2012
Desktop Xp 3 and connected printer, Comcast cable, WRT160N, wireless laptop w/ Xp 3. Printer is only parallel, and is connected to desktop. How to setup all and print wirelessly from laptop through WRT160N to printer on desktop?
View 2 Replies
View Related
Aug 1, 2011
I have a simple question; Does the E4200 have a print server built into it? I have a usb printer that I want to attach to the router so multiple computers can print to it. The printer does not have ethernet or wireless. I will be upgrading the printer later but would like for it to work with all my computers at the moment.
View 9 Replies
View Related
Aug 30, 2012
How can I set up iphone 4 to print using a router model E 3200,to the printer model canon MP520 via USB.
View 2 Replies
View Related
Nov 9, 2012
I can get regarding using the Collobos Fingerprint software through my WRT150N router. I'm using Windows XP SP3 and immediatly after installing (which went extreamy well) it immediatly found and listed all of my home network printers. All of the wired and wireless windows based systems in my house can see and print to the printers without any problem. However, getting ANY of my apple devices (iPad, iPhone etc ) to print will not even show them as listed on the device when I select print on the devices. Collobos says that I have to make sure that Ports UDP 5353 doe Bonjour and TCP 6361 for FingerPrint need to be open both ways for it to work, I have no problem getting into the router settings and have set them up as stated above in Port Range Triggering and enabled. Also made sure Filter Multicast was not check marked in Security. Unfortunatly, that doesn't seem to work as I had hoped.
View 3 Replies
View Related
Oct 18, 2011
Since firmware 1.0.02, E4200 supports connect printers to USB port and print to it from Windows using CiscoConnect.Is there any way to print from Linux (using CUPS, LPD, etc)?
View 3 Replies
View Related
Dec 6, 2011
I have an HP LJ4050 plugged right into one of the open LAN ports on my E4200 with a CAT6 cable. Can this router work as a LAN print server? I can't pull up the IP on a browser window or ping it successfully.The 4050 doesn't have USB capability and I don't want to use the parallel port on my PC unless I have to.If possible, I'd like to have wireless computers on the network be able to print to it as well.
View 5 Replies
View Related
May 7, 2013
I have been using the Wireless G broadband router WRT54GL for about a year now. Recently we bought HP laserjet network printer which is connected to the domain network with the ip range of 10.1.1.1 which is the same network linksys router is connected to. Since router always lease different range of ip (192.168.1.1) then all computers connected through router cannot print because they are in different network/ip range.is there a way allow wireless user to print to the same printer regardless of the ip difference?
View 5 Replies
View Related
Aug 3, 2012
When I try to install the USB software "CiscoVUSB" on MacBookPro running OSX10.7.4 I receive the following error: "The following installation step failed: run postinstall script for Cisco VUSB Installer. Contact the software manufacturer for assistance." Spent over an hour with support last night w/o issue was escalated.
View 4 Replies
View Related
Sep 19, 2012
After I had Prism high speed internet installed (made by Cisco) and I can no longer print using my Dell V313s Wireless printer. I have lost the driver disc that came with the printer and Dell wants to charge me a large fee for support and Prism states that they are not responsible for the printer not talking to the computer.
View 3 Replies
View Related
Apr 20, 2013
Few months ago I have bought Linksys E900 N300 router and its working fine. I also have a USB printer (make: Canon LBP2900) and Laptop (make:Lenovo G580). I want to make this printer wireless and through my laptop and router I want to give prints to this printer. Is it possible to do like this?
View 2 Replies
View Related
Apr 18, 2012
Linksys WRT120N to 811.11n? I set to 811.11N Only with 40Mhz, saved and reboot the device but the signal continuous in 811.11g.
View 3 Replies
View Related
Oct 28, 2008
Since installing my WRT160N my printers have stopped working. All printer drivers have been removed including acrobat and my fax.
Even if I try reinstalling my drivers, I get the following error: Spooler SubSystem App has encountered a problem and needs to close.
Prior to this error my firewall was giving me constant warnings about Pure Networks Admin assistant application trying to access the same files(i.e. nmctxth.exe). Even though I allowed it still kept popping up.
I am using the online armor firewall on a Windows XP system. I cannot access the LinkSys Advisor anymore as it will not start.
View 4 Replies
View Related
Aug 17, 2012
Been on the phone with Canon and they seem sure its the router. Linksys guy saying it was file sharing turned off. It was not..... I can print when I'm hooked in with an ethernet cable but not when I am on wireless laptop. Any setting I need to check in the E3000?
View 9 Replies
View Related
Jan 22, 2011
I recently bought an E3000 to replace my failed WRT54G v5. With the E3000 I can't get my shared Windows folders to be accessed from my other PCs. I called telephone support and they informed me that the E3000 doesn't support file & printer sharing. WTH? Is this true? If so, I'm going to return the E3000 and get my money back. But I never heard of a router not supporting file & printer sharing. My WRT54G handled it just fine.
View 8 Replies
View Related
Jul 20, 2012
I have a WRT 300N router. I can print when I am not in security mode, but cannot when the router is secured. Using a HP Deskjet 3050A printer
View 4 Replies
View Related
Mar 10, 2012
E3200 firmware 1.0.03 build 9. HP 1012 attached to USB port of the router. On a PC with Win7, Print Preview hangs in all applications. Print... also hangs in all applications. Reboot, re-installation of print driver, change default printer do not fix.
View 2 Replies
View Related
Jan 27, 2012
Can I plug my HP 3210 printer into my router usb and print wirelessly from my moterola droid ?
View 1 Replies
View Related
Jul 14, 2012
Currently my setup works fine except that I need another ethernet port.I have a E4200V2 with a HP laserjet 4000N printer connected via JetDirect ethernet and I am able to print with any of my devices.However, because I have need of another ethernet port, I am wondering if anybody has tried using a parallel to usb cable? The parallel side of the cable being connect to the printer and the usb side to the router.
Or if I really want that port made available, will I have to get some type of external print server?
I know that HP makes a JetDirect Card with a USB port, however, I don't want to spend the $80 on ebay to get a used one if a $10 new cable will work.
View 9 Replies
View Related
Jun 1, 2009
i'm setting up a wireless network for a local B&B they currently have a Linksys WAG54GS ADSL router in one of the rooms but need the wireless signal to reach each guest room the house has thick brick walls and an upstairs.i was thinking of using 2 x repeaters, the WRE54G's, and to put one on the ground floor within range of the current ADSL router and to put another on the 1st floor within range of the repeater on the ground floor to receive the bounced signal.I don't know much about these repeaters and how they work exactly and so unsure if this would be a viable solution in my case.
View 6 Replies
View Related
May 18, 2011
I bought a new Linksys WRT120N modem which is working great, but the wireless for some reason isn't working properly. My computer is able to sense the exsistence of the connection tho. I've tried using other computers to connect to it, and still the same problem, can sense but cannot connect.
View 8 Replies
View Related
Mar 25, 2011
I currently have a network using ipaddress 10.1.x.x and 10.2.x.x and 10.3.x.x with a subnet of 255.0.0.0 I purchased 2 of the wrt120n wireless routers for testing and find I can not use the subnet of 255.0.0.0.
View 9 Replies
View Related
Oct 29, 2009
I have a WRT120N and have been trying to set up priorities using the QoS under the tab Applications and Gaming. Everytime I "Save Settings" it does not save. It refreshes the page and deletes everything I just set up.
I did Live Chat and they told me it was my router. I returned it and got another one... Same problem
View 9 Replies
View Related
