I got my WRT54G from my son when he moved out of his apartment but he could not find the manual and software, I can download the manual but what about the software? I got laptop for xmas and it has Vista Premium on it and I want to install the Linksys but I am not sure about the software, do I have to have it to install?
View 9 RepliesInstlling WPA2 on my router I had this router WRT54G ver 6 for several years and it works perfect only thing is I have no security on my n wireless
View 3 Replies View RelatedI have a Linksys WRT54G to which 2 computers are connected of which one has no problems at all.The other computer just had its hard drive replaced and Windows XP Pro SP1 installed on the new hard drive. With the new operating system, I cannot get the computer to access the router. The connection status reports that the network device is working but IPCONFIG /ALL reports nothing (blank). The NIC is onboard the motherboard (ASUS P5LP-LE). I have swapped out cable ports at the router and tried a different cable to the faulty computer to no avail. If I had a spare NIC I would already have tried that too. FYI, it was working without problems prior to the hard drive crash that prompted the new drive and OS install.I tried a wireless USB network interface (Zonet ZEW2508) and the computer also reports it working. However, the network icon continually cycles between connected and unavailable, about 6 seconds connected and 1 second unavailable. IPCONFIG also reports blank on this.
View 11 Replies View Relatedinstall linksys e3000.
View 1 Replies View RelatedHow to install linksys wireless router to access point?
View 1 Replies View RelatedI currently have Comcast as my ISP.However there are only 4 wired ports on the router and I need an additional 2 ports for my needs. I have a 2wire 38000HGV-B Uverse Wireless gateway. I wanted to know if I could use one of the output ports from the Comcast wireless gateway and feed the 2wire Gateway to achieve the additional ports that I need. Also the wireless router from comcast is so difficult to setup that I don't even use the wireless. The 2wire gateway is much easier to setup and use and I could have wireless available where I don't have it right now.
View 2 Replies View RelatedI just bought this router yesterday. Can someone link me the most up to date firmware, and explain how to install it?
View 9 Replies View RelatedI have XP 64bit OS and I can't seem to get the setup CD to install E4200 Router. I have looked at the FAQ and it says it should be compatible with all Windows OS. Is there a link out there to the drivers I need to do this?
View 1 Replies View RelatedI first bought the e1200 version and when I tried to download it on my computer, it worked at first and installed correctly, but the cisco connect didn't properly install. I was able to log into the router online setup page ONE time. I tried to reset it and reinstall but it will not work.So I thought ok let me go and purchase a better one (thinking it was the router version having issues). So I brought it back and purchased the E2500 and I am having the same trouble.
I have tried to reset it about 20 times and reinstall and it will not install at all. It still gives me internet, but I cannot log into the http://192.168.1.1/ page at all, it tells me internet cannot display.
We currently get our internet through a small company that only uses a static IP and I cannot get our WRT160N router installed so I can manually set up our internet connection. Is there any way to install the router without using the CD provided. I keep getting the error code 322 during installation.
View 1 Replies View RelatedI bought the EA6500 yesterday and tried setting it up with the CD that came with it and it tells me ( YOUR COMPUTER DOES NOT HAVE NETWORKING CAPABILITY ) and will not install. I have the capability for networking because I have a network. I was able to set the router up but not with the software on the CD. I have tried a number of times and still get the same message and when I click on view details this is what I get .I have a network adapter and it works just fine.
View 9 Replies View RelatedI have a WRT54GS which works fine with Linux both from both wired and wireless computers using Linux. But I reinstalled Win XP and now I can't reestablish a connection following the EasyLink advisor. I did have a connection under Win XP before.
The last instruction on the Easylink advisor tells me to look for something marked "local" I don't find that word on the screen.
My son gave me an E3000wireless router but the first instruction is to insert the CD and follow instructions. I don't have the CD. How do I install it? Also, this is replacing an older router that is installed and working. Can I install the E3000 without removing the older router first?
View 3 Replies View RelatedHow to install the Cisco/Linksys WRT120n wireless router with respect to using Roku.I have one computer, a laptop, which I'm using as a desktop, in that it is stationery and the only wireless device is the Roku. When I open Network File Sharing, sometimes i see 2 instances of linksys, other times just 1. general setup or whatever so I don't have to reboot the computer every 2 hours to watch Roku.
View 1 Replies View RelatedI have this router that wouldn't connect because I lost the password. I held the reset button for 90 seconds and it neverwould reset.
View 4 Replies View RelatedI came into an old Win 7 computer (64-bit) with a WMP54G v4.0 wireless card in it. Apparently the driver had already been installed previously but when I booted the computer it didn't acknowledge the existence of the card or drivers. I installed the driver from here[url]... and restarted the computer when prompted (the card was already in the computer). Upon restart the setup was supposed to complete, but it never came up. When I re-ran the setup it just said the driver is already installed.The card still isn't being recognized, scanning for new hardware in the device manager doesn't bring it up. There is an entry for a "Network Controller" with no driver installed, it may be the WMP54G but trying to manually install the driver doesn't work. Windows just says it can't find the driver even when I point the install wizard right to its location.
View 1 Replies View RelatedI have an Acer Aspire 5517 with Windows 7 Home Premium connected wirelessly to a Linksys E1000 which is connected to a surfboard modem connected to Comcast cable internet. I just picked up an HP Proliant DL360 server with no OS and no optical drive. It tries to PXE network boot when I turn it on. How do I use my Laptop to install a linux image via the network?I have read extensively about this subject for a couple of days now and jacked up my IP settings in my router as well as my network adapter a couple of times now. Everything is backed up and my original settings are written down. I have asked for advice from Microsoft and HP as well.
View 1 Replies View RelatedI am trying to install a wireless bridge on my network. It is a Linksys WET54G v3 wireless bridge. I follow the instructions to configure the bridge: attach the antenna, plug the Ethernet cable into the bridge, plug the other end of the cable into the RJ-45 port of the hub (a Linksys WRT300N router), plug the power supply, insert the setup disk, and run the setup program. After following the steps, it came back and said it could not find a wireless bridge on my network. I tried just plugging the wireless bridge directly into the PC (as it was one of the alternatives in the instruction) Ethernet port. I got the same message. The set up on my wireless router is as follows, DSL modem connects into wireless router, and wireless router connects to PC Ethernet port. I am thinking, connecting the wireless bridge to one of the ports on the wireless router wouldn’t necessary allow the PC to know it is there, would it? Could it be that I don’t have a network? Does a wireless router form a hub?
View 9 Replies View RelatedWhen I try to install the USB software "CiscoVUSB" on MacBookPro running OSX10.7.4 I receive the following error: "The following installation step failed: run postinstall script for Cisco VUSB Installer. Contact the software manufacturer for assistance." Spent over an hour with support last night w/o issue was escalated.
View 4 Replies View RelatedNotified of new firmware for my router. Tried to install. Downloaded fine but will not install. Keeps saying error but not what kind, how to fix, not anything.
View 1 Replies View RelatedWould like to get another CD to install a wireless network for Cisco wrt160n v2 router. I have rest the router to factory default. Would prefer to download the install wizard CD if possible.
View 8 Replies View RelatedThis is about to cause me to buy another router. This will be the 4th clean install that I have had to do. If my power, or my internet goes down, a regular proper reboot / or reset, will not get my ea2700 back online. It takes uninstalling & deletion of the stored Application Data files.
View 8 Replies View RelatedTrying to install an E1200 inside a PPOE modem. I put in the account and password in the PPOE settings. I can see that it connects okay. But, my clients connected to the router (whether wired or wireless), do not get authenticated, so I can't get anywhere with them. Should I make the modem be the source of DHCP?
View 5 Replies View RelatedI'm looking to upgrade my WRT54G as I have had NO luck in getting my Galaxy Tab to connect through it so far (can connect and get an IP address but can't get out to the web) and have had intermittent problems with my Blu-ray lately. I am looking for something with the best affordable range, live 3 floors down from the current one and get about 3/4 signal strength so there's not much interference it seems. I watch a lot of online content through Hulu, Netflix, and LMB games and share with 2 other people.I am looking at the E series, probably the E1200, 1500 or 1550 as they seem to meet my needs. Any users have any advice about the ease of install and use of either of these? Or would it be better to get a gateway as we are considering going from DSL to U-verse service, twice the speed for $2/month more
View 6 Replies View RelatedIm trying to install the e2500 router on my sisters macbook, but it says it is an "unsupported operating system". She has operating system 10.8.1. Why am i not able to install It?
View 1 Replies View RelatedJust purchased new N750 model EA3500-NP and everything went ok until I tried to get my HP Laser Jet P2035n online. No go! It worked fine on the D-Link via Ethernet connection.
View 4 Replies View RelatedI have managed to install a printer on my computer using the USB port on the E4200 router.I'm just wondering is it now possible to install this printer on other computers / laptops.I'm not really sure how the printer is assigned. Is there some network share I can connect to?
View 8 Replies View RelatedI just received the E4200 and it has 1.0.01 loaded. Is it smart to install the latest software or should I just let it alone?
View 1 Replies View Relatedi got this wireless router (linksys version WRT54G) from my aunt but she can't find the disc for it. is there a way to use it without buying anything (this is mainly for my wii), if so how?
View 2 Replies View RelatedI have an old wireless router lying behind me and I want to use that old router as a switch. That old router is a knock-off,no-name router brand called "Gigafast" and the model number is WF19-CAPR. There are also variants to that router name as well.The router that I currently have is a Linksys WRT54G wireless-G router. I'm planning to upgrade the wireless router in favor of Wireless-N in the near future.I want to know how can I use that particular Gigafast router as a switch and I want to link that router up to my WRT54G router. The scenario goes as follows:
Cable internet connection ----> WRT54G router ---> Gigafast router (as a switch)
The IP address for the WRT54G router is 192.168.1.1, while the Gigafast router is 192.168.1.254. I may know by now that I have to disable DHCP on the gigafast router and I have to change an IP address to something that is "not in range" with the WRT54G router, am I right?I want to expand the number of ports, so I can connect with future devices such as a VoIP ATA adapter, a laptop and possibly an entertainment box (i.e. Apple TV or Boxee box)
I have lost the start-up cd for my router, where to find a downloadable one so i can hook up my router.
View 1 Replies View Relatedhave one router WRT54G with firmware version v2.02.7, Feb. 27, 2004, and I'm trying to use this router to get my PS3 connected to the internet, but in the PS3 appears that I'm using NAT Type 3 and to enable some online features in my PS3 I must change it to NAT Type 2 (from the router configuration), I tried everything that I found (put my PS3 in DMZ zone, enabling TCP/UDP ports, enabling/disabling UPnP, disabling Media Server Connections in my PS3, etc.) and nothing works,
View 3 Replies View RelatedOur office has 2 connections to the internet. Each connection comes into our building through a Linksys WRT54G router. I like to connect the routers together through their ethernet ports so that we can share resources such as printers and etc. Should I config each router such that they are actually on the same network? For example:Router 1:Router IP 192.168.1.1DHCP serves 192.168.1.100-150Router 2:Router IP 192.168.1.2DHCP serves 192.168.151-200
View 2 Replies View Related