how to add a WRT54GS V1 wireless router (Router B) into my existing WRT54G V2 Wireless network (Router A). The main router WRT54G V2 router (Router A) is located upstairs and is the link to the ISP (Internet).
- DHCP active
- Wireless MAC filter is enabled with only approved MAC's
- Wireless SID Broadcast is disabled
The secondary Router WRT54GS V1 (Router B) will be located down stairs with no Ethernet cable between the two routers.
- Will need this secondary router to connect to the existing wireless network Router A wirelessly.
- Will need to have internet access.
- Will need to have the wired ports to have internet access as well. Needed to connect the Home A / V receiver to update A / V firmware.
I have a WRT54G that has served us well for several years, but I needed a network connection in another part of the house, both wired for TV, and wireless for downstairs. So I ran an ethernet cable through the house and connected it to my new E1200. It's connected to Port 1, not the Internet port. The TV plugs into Port 2, and my Apple TV to port 3. So far so good, TV and Apple TV appear to work fine. Wireless is where I'm having problems, the wireless signals between the two routers appear on Wifi Analyzer I'm using. Both appear strong in signal for a second, then they disappear, then they appear again for a second, then they disappear. So the wifi's signals appear, then disappear and this cycle continues.
The WRT54G is setup with DHCP, channel 6.
IP Address: 192.168.1.1 Subnet Mask: 255.255.255.0 DHCP Server: Enabled Start IP Address: 192.168.1.100 End IP Address: 192.168.1.149
The E1200 DHCP is disabled, channel 11, 20mhz.
Router IP Address: 192.168.1.2 Subnet Mask: 255.255.255.0 DHCP Server: Disabled Start IP Address: 192.168.1.1 (DHCP disabled) End IP Address: 192.168.1.50 (DHCP is disabled)
I've tried both routers named the same, and then tried 2 different names. I've rebooted them as well after making changes.
Recently I had to reconnect my WRT54GS linksys router and now it is unsecure, obviously i know how to secure because i've done it before but it isn't letting me...Whenever I type 192.168.1.1 into my browser it will not load the page and it is really frustrating. I have also tried typing in my Default Gateway and ip address that I got from cmd/ipconfig and those will not work either..I'm not understanding why this wouldn't work, and yes my internet connection is fine and nothing is wrong with my browser..
I work for a large company and want reinstall my wireless router so I move from room to room with my laptop without plugging into our network. I have had it set up before but had to spent an hour with tech support to configure the router. Recently I had to reset the password and lost all the settings.
I can get to logged into the set up with the default password but have no idea how to configure it. No matter what I try I get no conectivity when I try to redirect the browser to the internet.
Yeah, I know I should let our network IT staff set it up, but they get all bent when I want to extend my access to a wireless configuration even if it's password protected.
My laptop can't find the wireless Linksys network when I go to connect to a network. When I plug it in directly, with no router, it works fine. My laptop is a Compaq Presario V6000 (Vista) and the router is WRT54GS
I have an existing wireless network using a Cisco/Linksys WRT400N wireless router (which in turn is connected to a cable internet provider). I need to extend my wireless coverage and so purchased a Cisco/Linksys E1000 to act as an additional access point. Purchased from BB, the local 'geek squad' rep instructed me to follow the users guide for the set up. After login into the admin service on my E1000, I followed the 'Advanced Routing' instructions and disabled the 'NAT' option and subsequently enabled the 'Dynamic Routing (RIP)' option. Everything worked like a charm to this point, but now I'm stuck. What steps do I need to follow to allow clients to log onto my wirelss network via the E1000 (secondary access point)? I've established WEP security keys on the WRT400N (primary access point) and want to use the same network security parameters on the E1000.
Model wrt54gsWindows xpI got the wireless network setup and password protected and my computer and phone can sign o the wireless network, but when I try to go to a website it doesn't work. If I connect te computer directly to the modem then it works.
I have a xbox 360 that I want to connect to xbox live with, using my home network. Every time I try to connect to xbox live the only part that fails is the connecting to xbox live part. This is how my network is set up. I have Cox Cable as my ISP, a Linksys WCG200 gateway(v2), and WRT54GS(v7). The cable wire is connected to the WCG200 gateway, then an Ethernet cable connects the gateway to the WRT54GS router, and finally an Ethernet cable connects the router to my xbox 360. I have contacted Cox, Linksys, and Microsoft about the situation and they all say the problem is the version of the router. Someone told me that I may just need to change the firmware, but I don't know how to do that.
In the house I am using a WRT54G as the main router connected to the ISP. I have run a Cat5E wire from the house to the shop 110 feet away and connected a WRT54GS to the Cat5E (a LAN Port). I turned off DHCP and assigned it a static IP from the House WRT54G. Local wired connections work great, problem is it will not offer up a wireless IP address to wireless clients.I wired up a cross over cable and actually plugged it into the WAN port, it actually picked up and offered wirelessly the House IP address range, however, could not get to the internet. Why I can't wire to WRT54G and a GS together and expect a wireless connection at the shop site?
I currently have a LinkSys BEFSR81 connected to my cable modem as I need at least 6 wired ports for my house network. I also have a WRT54GS that is currently unused, but I would like to add it to the network so I can have some wireless connectivity as well.
Assuming that it's possible, what's the best way to combine these two units into the same network? Can the WRT54GS simply be connected downstream from the BEFSR81 via one of the open ports? I'm assuming that I'll have to change the IP address on the wireless unit to make it individually accessible for configuration, status checking, etc.
I recently had trouble connection to my Linksys WRT54G router. However, in this process I had to create a couple of new profiles/networks/SSID or whatever they are called. I now have one functioning network, but my router is still broadcasting the other two networks. How can I get my router to only broadcast the one network, I am currently using? I erased them from Vista, so that my own computer does not automatically log on to the, but that is clearly not enough. Since one of the networks is not secured with a password (dont ask why), my concern is that my neighbours can access it. BTW, I am using Windows Vista on a Toshiba Satelite A200.
I've downloaded the driver for a tenda usb adapter. What else do I need to do to connect to the WRT54G network? I'm currently connected via an ethernet cable. Running Windows/7.
I have the following equipment E2500 wireless N router (2 of these) WRT54g router (B/G) WAP54g access point (B/G)
I am planning to set up a wi-fi network for a single story motel. It is C-shaped; about 300 feet along the longest side with "legs" of 120 and 70 feet. I have included a diagram that I drew for the person that will install it. Until now I have only used that single WRT54g in the office for the entire property and it covers about half the property (left side) but not well and with a dead spot in the top left because of too many walls to go through.
My plan starts in the office (bottom left) with a WRT54g connected to the DSL modem as it always was. That would be connected to one of the E2500s in the middle so it can cover the most area. From there two others would shoot out to each corner (the other E2500 and the WAP54g). They will all be wired together with Cat 5e "riser cable". The routers will be placed in a wide open attic.
1. Is this is a good plan for the size of property? I have heard that N routers have a range of 150ft in every direction so that's why I'm putting one in the middle. Keep in mind that while the attic is open and wood constructed, the walls between rooms are concrete firewall and they haven't been wi-fi friendly. Hopefully putting them in the attic takes care of this.
2. Does starting with a B/G router at the modem mean the N routers will revert to B/G?
3. What are the main settings I need to know about? What "mode" does each need to be set to? Do they need different default gateways?
Can I use the same password/security for all of them? Should I use the same SSID for all?
Yesterday i was playing online on my Xbox 360, and was disconnected from the internet. I came downstairs to reset router/modem, once doing so i went into the router settings for my Linksys WRT54G. My modem by default uses the 192.168.1.1, so my router was 192.168.2.1... So i powercycle, log into router settings through 192.168.2.1 and start setting up my port forwarding for the xbox ports. Saved Settings, and the page would not load to say "Settings Saved". Closed the window and now my pc says no internet connection. I had to create a VPN broadband connection to even use the internet on my pc. I can no longer log into 192.168.2.1 for my router, nor can i access 192.168.1.1 to even get into my modem settings.. I'm using windows 7, and the automatic troubleshooting guide tells me to powercycle my modem. My xbox can still see my wireless network "linksys" but will not connect to it, even with the VPN connection i am still hooked though my router and modem.. Im afraid that my router just out of nowhere "died"..
I have been using this router fine for a year now. Now I can only get on the internet if I am directly plugged into the modem. It says I have limited connectivity. My ISP is Comcast. I have tried resetting the router with no luck. I have tried to update the drivers but I cannot even log into 192.168.1.1. I am in dire need of the wireless cpability. When I go to the run command and type ipconfig it tells me I have no default gateway.
So I have a WRT54G router since a couple of years now. Laptop (Win7 64bit), ipod, ipad, phones can connect to it without a problem, but new computer (Win7 64bit) can't. I can connect the PC via ethernet without a problem though.
I powercycled my devices, I changed broadcasting options off and then back on, changed my security mode, tried the MAC Cloning (after doing the MAC Cloning, I lost internet connectivity even through ethernet), resetted my security settings, changed SSID, I'm broadcasting through channel 11 2.462. I also tried deleting the HomeGroup
Important fact: the network is in the list of available wireless network, but Signal Strength is No Signal and I can't connect to it. My network adapter is ASUS 802.11n Wireless LAN Card, drivers are up to date. I've upgraded to the latest router firmware.
I have a wrt54g router and would like to separate the WLAN clients from accessing computers and servers on the LAN... in other words I would like to make it a "guest" network. I've put the router in "router" mode instead of "gateway". I just want to be sure if that is the best thing I can do in terms of turning the wireless network into an isolated one.
i have a linsys wrt54g router. my main computer is connected (wired) and works fine. until today my wireless devices were able to connect and access the internet using the router. now the ssid does not show as a possible network connection. i have unplugged everything, rest the router, checked setting, shutdown and reset every computer and all my wireless devices still cant locate the network connection???
My network keeps losing the lock icon that displays with the network name. I think this is happening with power shortages or outages. I have checked the settings online and it says WPA Preshared Key. Is the network still secure? I have a WRT54G wireless router.
I have a Cisco network at my office and the router and everything is set up under my desk.I can use the internet just fine on my office computer but I am trying to use it on my laptop and login to the guest account .I ran across the Cisco Connect sofware and that I need it to find the password but the problem is I dont think I have a router or whatever it is that is compatible with this software I am using WRT54g wireless n router, the models on the site for the cisco connect are e series
I've tried looking for solutions on the windows seven forums and all over Google but none of them worked.The problem is, sometimes I get an "Unidentified Network, No Internet Access" error on my laptop (wireless). When this happens, the lan speed drops to 1.0 mbps and I get the "No Data Received" error when I try to load pages.My internet is on fine and my brother can access the internet fine on a desktop which is wired to the router and modem. My mom's notebook sometimes gets this error as well.
Is there any real solution for this problem or known compatibility problems between my WRT54G (version 1.1 I think) and Windows 7? Really need a solution to this, before I had to re-setup my whole connection, I didn't get such a problem. My laptop doesn't get the error in the school network either.
I suddenly am unable to print the settings on the My Network Settings. When I click on the print sign nothing happens - it does not register on my printer. I used to be able to do this. My router is WRT54G and my printer is HP Officejet J3680 All- in-One.
Our wireless network has started to drop out periodically. If we pull power and restore, the network immediately comes back up on all our our devices. We have the WRT54G, and we have 2 PCs, 2 Macs, and 3 iPhones, and a wired home phone. Normally there are not this many devices connected, but with everyone home for Thanksgiving and all these devices on the network we have started to see this issue.
Are there simply more devices than the router can handle? Is one of the devices crashing the network for everyone? What typically will cause something like this?
I had an XP machine using a wired connection with a Linksys WRT54GS 2.4GHz router. The only things connecting to it wireless were my wii and my PS3 which were in the next room, less than 15feet away. I purchased a Windows 7 machine for my wife for Christmas, and gave the XP machine to my kids. I moved the modem and router into the kids playroom, and set the Windows 7 machine up for wireless. Now the router is at one end of the house, and the 7 machine is about 45 feet away. The signal strength was never an issue until last week, and now the PS3 and the Win7 machine constantly have weak signal or no signal. I don't know a whole lot about networking. I am willing to move the router and modem to a central location as a last resort, but would like to keep them with the XP machine for our kids to use.
I've been having a ton of problems with fixing my connection with my wireless network. A few months ago, I lost connection on my desktop computer and I reconnected... however, it didn't actually connect. When I hovered my cursor over the Wireless Network Connection icon, it just said "Acquiring Network Address" and never connected. I got onto my laptop and did a quick search on the problem. A few wrong moves later, and I couldn't even find my wireless network.
Despite all of my attempts at creating a connection, I still have no internet. I've even tried plugging my computer into my WRT54G router via cable, and still no connection. It's not the router that's the problem, though, as my two other computers and xbox have perfect internet connection.
I use Windows XP, I use a WRT54G router, I have Mediacom high speed internet, and that's about all I know.
I moved into an apartment complex that has wireless already set up, but it is so slow! I heard that if I connect with my own router then the speed will be faster. How do I configure my router for that? I have a netgear WGR614v.10 and am using a macbook pro.
