MS Access Databases - File Location Did Not Exist And My Whole Database Disappeared?
Jul 18, 2012
Our company has a Server in the office to which we all map network drives.This server is backed up to a Cloud Server (egnyte.com). Whenever I am working on a database on the mapped network drive, it freezes up after 5-10 minutes with the alert "Your network access was interrupted.To continue, close the database,and then open it again."
This problem does not occur with any other Office Products,only Access.It happens to all databases on the server and to all users.
It does not do this when the file is saved on my desktop or when I am working on it directly through the cloud server. When working on the cloud server, however, I went to Compact and Repair my database and a window came up saying the file location did not exist and my whole database disappeared. It was already saved in the file location, I was just compacting and repairing.
Is there some problem with using a local server that backs up to a cloud that makes it lose connectivity every few minutes? Why is this only happening with Access?
View 7 Replies
ADVERTISEMENT
Mar 22, 2012
Recently I installed LMS 4.1 accidentally on the c-drive, which, as a result, fills itself with a growing database and associated logfiles. How can I move both items to another drive safely? I allready managed to move configs and downloaded software.
View 7 Replies
View Related
Dec 16, 2012
Questions / Integration Adapter Cisco Prime.There is an integration adapter for HP uCMDB to get CI information from Cisco Works (Prime whatever ….).We set up a user for CW according to “Open Database Schema Support in Cisco Prime LAN Management Solution 4.2” , page 1ff.According to this document we created a user lmsdatafeed. If we run this integration from HP uCMDB / DDM we can connect to rmeng database using jmx to port 43455, but we have not sufficient privileges to get all the needed information. We tried to connect with a user that has full rights (Admin User), but we cannot connect at all with this user. We use Cisco Prime LMS 4.2 and we want to have our network devices as Configuration Items (CI's) in our HP uCMDB Our question:Would it be save to give more privileges to the user lmsdatafeed ? And if yes: How can this be done ?Is it possible to give an admin user the rights to connect by jmx/jdbc ?Below I post the communication protocol of the adapter, connection is OK and the first select statement to, but them this user doesn't have enough privileges. The error messages are in german for some reason ... (means: "User has not sufficient privileges to selet from DM_Dev_State")
==== snip =====
execution jobId="DS_CiscoPrime_CiscoWorks NetDevices" destinationid="e6ac2661c751b23929fb1cf4f97a536f">
<destination>
<destinationData name="id">e6ac2661c751b23929fb1cf4f97a536f</destinationData>
<destinationData name="ip_address">172.28.193.55</destinationData>
[code].....
View 7 Replies
View Related
Feb 17, 2013
I was curious what is the best way and how to setup a network that can do the following:I have two offices in different cities but I need them to be able to access the same database file.I can easily share a folder in 1 city and have all those computers access it but how can I share the file with the computers at the other city?
View 3 Replies
View Related
Apr 18, 2013
what is location of flash file in 6500 Series switch and how can we take back of IOS image for 6500 series.
View 4 Replies
View Related
Jan 12, 2012
so far i also knew that if u assign an access-list to an interface:
for example:
int vlan1
ip access-group 150 in
and the access-list does not exist in the configuration it will block everything meaning it will be an implicit deny empty access-list but lately i've noticed on new routers that its different,if i assign an acl to an interface where the acl doesnt exist in the configuration it acts as permit all,
View 3 Replies
View Related
Jun 14, 2012
Access Restrictions option does not exist on my WRT160Nv3 Broadband Router Setup Page and I need to use that option.
View 2 Replies
View Related
Jul 26, 2011
I am working on a Drupal site which is on a virtual server (the way it's been explained to me). I've been told I need to work with it through webdev. So I can copy a file off the server and onto my local machine. I make my edits and then try to upload it to the server. I get locked out with the message: Error 0x80070021: The process cannot access the file because another process has locked a portion of the file. I have tried shutting down my code editor, opening and closing the connection, tried different methods of reaching the server (Cyberduck and through Window's map network feature) to no avail. What can I do?
View 1 Replies
View Related
Sep 22, 2011
what is the database to use cisco LMS3.2 and how to access the database?
View 3 Replies
View Related
Dec 10, 2012
how to perform Linear Hashing in databases on given values?
View 2 Replies
View Related
Feb 7, 2012
We currently use ACS 4.2 for authentication of corporate users who are accessing the network in 2 different ways:
1) VPN client (via ASA5510)
2) Wireless (EAP-PEAP)
For all users who currently access the network via either of the above 2 methods, the Password Authentication under User Account settings in ACS is set to query an RSA SecurID Token Server.
We would like to try achieve the following in ACS:
IF an access request comes from the ASA (VPN clients), THEN we would like the user's password authentication to be handled by the RSA SecurID Token Server as it currently is. IF an access request comes from the Wireless LAN controllers THEN we would like to use EAP-TLS authentication. (We are aware that we would obviously need to configure the WLC, clients, PKI infrastructure etc accordingly for eap-tls).
View 1 Replies
View Related
Feb 21, 2011
what is the easiest method permitting a local and a remote pc to access the same database ? They both have internet access.
View 3 Replies
View Related
Jul 12, 2011
Because of limited budget and a paranoid boss, the MS Access database at work is running through a simple Linksys wireless E2000 N router rather than a more dedicated server setup.A desktop server PC is storing the Access database and 3-4 laptops are connecting to the split database linked tables via laptop wireless N adapters only.Upon having several people accessing and updating records we've noticed a huge amount of instability frequent network interruptions.I have several theories/observations:
1) While not an ideal location (one end of the building), signal strength is consistently shown as 4/5 bars to 5/5 bars, even through several walls
2) Interference: Several other routers, all on 2.4Ghz could be creating too much interference. (none of the laptops support 5Ghz)
3) Number of individuals accessing the database at one time. This is where I'm unclear. Could having 3-4 people working on the database at once pose any potential problems? I'd ordinarily think not but I am coming up short with explanations.
Last week two of us were working with the database, updating records and such, from probably 100 ft or more away with no issues. Then the last few days just to stay connected requires being within 5-10 feet of the router AT MOST. No settings have been changed and network disconnects/interruptions in Access are happening every few minutes.
View 4 Replies
View Related
May 3, 2012
I'm essentially looking to extend an existing network in a primary warehouse for our company across a parking lot to a secondary warehouse with no network drops. I need to keep the ability to assign addresses in the existing scheme over to two computers in the secondary warehouse.
View 1 Replies
View Related
Jan 15, 2012
My son ran some program that he didn't know what he was doing and now there is no Network access. As far as I know this is what caused the problem, but I'm not certain. When I tried to reinstall the drivers an errors pops up stating that the drivers couldn't be installed due to "Invalid Access To Memory Location". The networking card is an Intel 82566DC-2 Gigabit Network Connection Adapter. The Networking card is part of the Motherboard. I have the original drivers but they will not install due to the "Invalid Access To Memory Location". Anyhow my son went and bought a new networking card, and it gives the exact same error. I tried uninstalling the networking card in the device manager, but when the hardware is reinstalled, and the drivers are about to install it gives the same error. computer is a Dell XPS 420 with 6 gigs of RAM, an Intel Core 2 Quad CPU Q6600@2.40GHz Also in the Device Manager everything under the Heading Network Adapters has a Yellow Triangle with an Exclamation mark in it. I know that this means that there is an error somewhere. I also want to add that when I checked the Netgear GA311 Network adapter card (this is the new card that my son bought)in the Device Manager it says This Device is not working properly because windows cannot load the drivers required for this device (code 31).
View 9 Replies
View Related
Apr 12, 2011
Main Site allows communication from Remote Site via VPN to Windows ServerMain Site also has a secondary subnet that communicates ONLY through internet but NOT to the Windows Server.Sonicwall 192.168.168.x is main siteRemote Site is 192.168.0.x connecting to Main Site to access shared folders on serverSecondary subnet at Main Site is 192.168.0.x using Windows XP PC's. They are accessing a linux server at 192.168.0.215 which Main Site has no access to.VPN remote ip's are 192.168.0.x - they can successfully access the Windows Server at 192.168.168.100 BUT NOT 192.168.0.215.GOAL: Want to connect Remote Site to Secondary subnetWilling to make router changes or whatever is necessary to get Remote Site to access Secondary Subnet with the only exception that the Secondary Subnet REMAINS.VPN DHCP is turned off but willing to turn it on.Willing to make the Linux Server 'discoverable' on the Windows Server. Don't know linux at all but another co-worker set it up and can make changes.
View 4 Replies
View Related
Jan 17, 2012
We got some serious issues to get APs running on a WLC 5508 (7.0.116.0). The APs were added and configured in the WCS, but no SSID can be found by clients (802.11b/g Network Status is enabled).
The radio led is blinking green on the APs which indicate that the "access point location command" has been invoked. What's the meaning of that?
View 2 Replies
View Related
Dec 2, 2012
Can I use the access point 1242 to do clients location using WLC 5008, NCS 1.1 and MSE3310?On this moment I doesn´t need of CleanAir features. I want just to do location for clients and rogue aps.
View 2 Replies
View Related
Oct 31, 2012
I have the wireless controller 5508 and many AP1261 registered on site. It detects a lot of rogue access points around. I would like to find out geographic location of these rogue access points. Is it possible?
View 2 Replies
View Related
Mar 28, 2010
I have successfully setup the AnyConnect VPN (connecting to our ASA5510) and have split tunneling configured. My remote users can access inside LAN servers as well as the Internet from their remote location. What I would like to know is is it possible to change the split tunnel and not allow access to the Internet from the remote location but force the remote client to go through the VPN and out our internal edge firewall to the Internet? Basically I need my remote clients to access the Internet but I would like for their Internet traffic to go through the VPN and out our edge firewall. This will allow the same security as if they were sitting in the office.
View 4 Replies
View Related
Apr 27, 2012
Everyone speaks about video and music streaming, however I am under the understanding that there isint actually any such thing as legitimate real time streaming, ALL files are saved to the disk or the RAM. If this was not the case, disrupting your Internet connection would cause an instantaneous crash of the streaming media, and well, I have had my Internet crash a lot of times while viewing streaming median and in every case it continued to play for some time.
View 5 Replies
View Related
Apr 28, 2013
a have a router CISCO 1841 and I configured a NAT inside from the router to the firewall like this :ip nat inside source static firewall_adresse public_adresse and its work fine and when a added it I do this command "wr" to save the configuration and I restarted the router many times and it still work fine,but in the last five months this NAT does not exsit twice and I must add it a gain.
View 7 Replies
View Related
Oct 20, 2012
I've got a LAN set up with a server and printer, no internet connectivity to it. When I need to access the internet, I connect through a wireless hotspot. The only problem is that I have to unplug the ethernet from my LAN connection for the wireless to work.Is there a way to have both connections coexist, so that when I need to print something or access a file on my server I can do so without it interfering with my internet connection?
View 4 Replies
View Related
Apr 13, 2013
I know my Modem/router is old but I am connecting okay to the internet with my laptop, the thing is my husband has just bought a Google Nexus Tablet and although it finds my Belkin Modem (model F5D7632-4) it says it's finding IP address, then says its saved and then connecting, but it dont connect. Also there is no security on it and it wont find my model number to add the security, is it me or what?
View 1 Replies
View Related
Jan 6, 2012
Is there a limitation to the amount of sub-interfaces that can exist on a Cisco 6509? The switch has WS-SUP720-3B (Sup card), WS-X6724-SFP (linecard), and 12.2(33)SXH7 (IOS).
View 7 Replies
View Related
Oct 21, 2012
I am using ASA 5520 Image in GNS3, when i come in Configuration Mode and try to create Tunnel through command "interface Tunnel 0", but this command doesn't exist. I need this command to create Tunnel for GRE Lab.
View 2 Replies
View Related
Jan 16, 2012
Let me try to give as much info as I can to start. Running Windows 7 64bit Ultimate have all updates as of 01-16-2012. Recently had some malware that I removed not sure if there is a correlation. I am trying to connect my wireless connection on my pc to a router to run xbox and BD player. So I connect to my wireless network have my network card plugged into my router, connected to both networks. I go to properties on wireless connection click sharing tab check allow other network users to connect to the internet through this computer connection, also checked allow other network users to control or disable the shared internet connection. I click ok and get a error window that says in the title bar Network Connections the body of the window says, "An error occurred while Internet Connection Sharing was being enabled. The dependency service does not exist or has been marked for deletion. I looked through services and device manager in non pnp drivers everything looks right to me... I am not super familiar with networking issues so I may have missed or overlooked something easily.
View 12 Replies
View Related
Apr 24, 2011
i noticed this morn that my LAN has disappeared from my networks. just leaving my tplink wireless adapter, but have a network card in pc, but it has disappeared from device manager as well, but when plug in the modem it lights out, but still nothing, still nothing in device manager, using win 7 32bit actually i have 2, an on board one as well, but both missing
View 3 Replies
View Related
Dec 27, 2012
I'm having a Strange problem. When i try to Explorer files in a network location by typing \<Computer Name> it does not work, Network path not Found error appears. But i can browse files using IP Address.
1. This Happen only at this particular machine only. I can Explorer files using the Computer name from other machines.
2. nslookup shows the correct IP.
3. I can connect to the file server using Remote Desktop by typing the Computer Name.
View 1 Replies
View Related
Oct 24, 2011
I've got this problem about accessing a file server in my work office.
First, I used to have a desktop PC connected via ethernet cable to a wireless router (there's only one connection in this office but there are two of us, so we set up a router), and I was able to acces the file server by typing "\SERVERNAME" in the RUN command windows. I brought my laptop and I connected it to the router via wireless. After I tried accessing the server the same way I used to (typing "\SERVERNAME") but I got the "Windows cannot acces \servername". Well, I said, I'll try by connecting via ethernet cable, but I couldn't connect either. The only way I can access is by disconnecting the internet cable off the router and plugging it in my laptop's ethernet port. But the issue is that we've only got one connection and some other people connect wirelessly too. I can't understand why if connecting an ethernet cable to the router's LAN port, I was able to access the server from my desktop computer but when I tried the same way from my laptop I could not.Internet connection works fine in my laptop. Networks settings are ok i think. My laptop has Windows 7 and my desktop has Win XP.
View 14 Replies
View Related
Jul 11, 2012
Tech Support Guy System Info Utility version 1.0.0.2OS Version: Microsoft Windows XP Professional, Service Pack 3, 32 bitProcessor: AMD Turion(tm) 64 Mobile Technology ML-28, x86 Family 15 Model 36 Stepping 2Processor Count: 1RAM: 1150 MbGraphics Card: ATI RADEON XPRESS 200M, 128 MbHard Drives: C: Total - 238464 MB, Free - 182597 MB;Motherboard: Quanta, 3093Antivirus: McAfee Anti-Virus and Anti-Spyware, Updated: Yes, On-Demand Scanner: EnabledOkay, that's one Notebook. The other is a Gateway w34OUI running XP Media Center. Both are in great condition for their ages. Good for them. I really want to network the two with an RJ45 crossover cable, and all the instructions I've found on our illustrious internet tell me it's easy. HOWEVER, when I've only begun to follow those instructions (one list is from the God Microsoft itself), NONE OF ANY of the sets of instructions matches the steps offered on either one of these notebooks. The options do not correspond. The results do not correspond. The closest I get is a window that says I do not have access to such file sharing. These are MY computers, and have always been, and I am attempting to network using administrator ID logins on BOTH. What's the REAL way to network only two notebooks with an RJ45 crossover cable?
View 1 Replies
View Related
Jun 16, 2012
How to connect my Windows XP Desktop to my homes wireless network system (my comp is outdated I know ). I have no trouble with my my mum's Windows 7 Laptop and no problems with my MacBook Pro, but how do I connect this old clunky XP to it?
Wireless Connections doesn't exist in my network connections tab, and in Services under Admin Tool - in the 'Wireless Zero Configuration Properties' is set to Automatic startup type and it is 'started'.
View 1 Replies
View Related
Jul 26, 2011
I have created a VPN client account on my RVS4000 router. I have installed Quick VPN on my laptop in the default directory -- Program Files (x86) / Cisco Small Business / Quick VPN Client
I have generated and exported a certificate -- RVS4000_Client.pem -- and placed that in the Program Files (x86) / Cisco Small Business / Quick VPN Client directory. When I attempt to connect using the Quick VPN client, I get the warning "Server's certificate doesn't exist on your local computer."
If I ignore the message I can log in, and ping resources inside the network and log into the router. However, I cannot mount any drives and the router shows that no VPN tunnels exist. I've read several posts here and elsewhere and can't seem to see where I've gone wrong.
View 1 Replies
View Related
