We got some serious issues to get APs running on a WLC 5508 (7.0.116.0). The APs were added and configured in the WCS, but no SSID can be found by clients (802.11b/g Network Status is enabled).
The radio led is blinking green on the APs which indicate that the "access point location command" has been invoked. What's the meaning of that?
Can I use the access point 1242 to do clients location using WLC 5008, NCS 1.1 and MSE3310?On this moment I doesn´t need of CleanAir features. I want just to do location for clients and rogue aps.
View 2 Replies View RelatedI have the wireless controller 5508 and many AP1261 registered on site. It detects a lot of rogue access points around. I would like to find out geographic location of these rogue access points. Is it possible?
View 2 Replies View RelatedBefore running firmware asa722-k8.bin and asdm-522.bin ASDM "asdm location" config lines were created when we created a network object. After the upgrade to asa722-k8.bin and asdm-522.bin this dissapeared.We recently upgraded to asa724-k8.bin and asdm-524.bin which brought those config lines back.So if "asdm location" is needed, if not can we make sure those lines wont pollute the config file?
View 3 Replies View RelatedWhen ever I create a network object in ASDM 6.0(3) the UI also wants to send the command 'asdm location (network object IP address)' to the device.What is the purpose of 'asdm locaction ....'? Is it telling the ASA-5540 that the IP address is allowed to connect to the device using ASDM?If that is the case why does 'asdm location xxx.xxx.xxx.xxx'get denerated for every network object I create?
View 3 Replies View RelatedI need to know if 3502p with outdoor antennas supports Point-to-Point Wireless Bridging?
View 6 Replies View RelatedHow would I bridge a wireless connection with a distance of 400 feet? Would twoAP1262N-A-K9 be able to make this happen? Or is there another wireless bridge that you all can think of?I would be connecting one AP1262 of off a 3750g switch and at the far end (400 ft aproximately) another AP1262N-A-K9.
View 12 Replies View RelatedI had a new AIR-AP1042N-N-K9 access point and I tried to convert it into lightweight mode with the image c1140-rcvk9w8-tar.124-21a.JA2.tar . I used all the methods but the AP is getting hanged at one position after decompressing the new IOS. The capture of the process is below: [code] After this I am getting the junk characters and everytime AP hangs at this position.
View 4 Replies View RelatedHow do I connect and configure my WAP54G wireless access point to my new Cable Modem? I have it connected to the modem but I cannot access it to configure it. It appears to be working but before I got the cable modem I had it connected to a router and it was set-up with a static IP address. With my new ISP, I no longer have a static IP address so I am trying to configure the WAP54G to use DHCP. Trying to access it thru the internet at 192.168.1.245 does not work.
View 1 Replies View RelatedI just bought an LG Bluray DVD player (BD390) which is unable to find the access point in my home network.My router is a WRT54G, ver. 2.2, running firmware: Ver.4.21.1. My home network uses high speed cable with two computers on the wireless network, all working with no problems.The router is on the second floor but the two computers and the new BD390 are on the first floor - about 35 feet away. I have the wirelss security set to none and use only the specific computer MAC addresses to allow connection to this network.
I found directions in the forum for a setup using the LG BD390 but with a different Linksys router. I changed the security to WPA (AES); the Beacon interval from 100 to 75; the Fragmentation Threshold from 2346 to 2304; and the RTS Threshold from 2347 to 2307. The DVD wireless connection still failed to find my network. There is a "Push button" connection feature on the BD390 setup which I tried, but the only "button" on the router I could find was in the basic wireless setting, a green icon for the wireless SSID setup. No connection was made there either.
The recommendation connection from the LG manual is for a network cable, but that would be over 50 feet and a real pain to connect, so I would prefer WiFi.
My company recently handed me 2 used 1252 AIRONET APs that they picked up somewhere to replace and add on to the current AIR-AP1121G-A-K9 that are currently used. I've been successfull at connecting via a Serial Connection in an attempt to the AP's IP via the CLI. But further attempts to connect to the AP via a web interface to continue setup have been a failure. After some research, how to confirm that LAP series products can only run Lightweight IOS, hence the need for a CISCO controller, or can I try to flash the firmware to make it into an autonomous AP.
View 1 Replies View RelatedI have 6 of the 1252 APs that suddenly no longer will associate with any of my 3 4400 controllers. I've verified the power injectors are up and good, shut the port on the switch, and even moved from one power injector to another. Also, in WCS there is a picture of what looks like 3 disks stacked on top of each other, and I don't know what that means.
View 2 Replies View RelatedI have problem with one AIR-LAP1252AG-N-K9 AP. When i am connecting the laptop through wifi to this AP i am getting blue dump. If the same laptop connect to any other ap i haven't get any error. Laptop Model no is Lenovo L412.
AP Has below IOS version.c1250-k9w8-mx.124-21a.JA2
I had to reset my access point but the login screen fails to appear to lock the router. I don't have the setup wizard disk.
View 9 Replies View RelatedI have a WAP54g hardware version 1.0.I install de last firmware on this access-point but, this access-point reset automatic after a random time..It’s it possible to downgrade de firmware from this access-point?
View 1 Replies View RelatedHave a WRT320N router at one end of the house in the basement. Would like to boost signal to other end of the house. Which product should i use, an access point or a range extender? My house is also wired with Ethernet cable and I could plug the access point into an Ethernet port at the end of the house where the signal is weak.
View 1 Replies View RelatedI have AP WAP 4410 N, and I want conected AP to cacti. Where is I faoun MIBs or OIDs for my Access Point?
View 1 Replies View RelatedI've got a AP WAP54G. I've managed to get into the configuration page and rename my router and set a WPA2-Personl password.
The issue I'm facing is that when me and my roomate try to connect to the router at the same time, it shows the laptop that connects second as one that has 'limited connectivity' and hence cannot use the internet. The 1st laptop however works fine!
The settings for the router have all been left to default.
I'm not sure, but does this problem have anything to do with the fact that the router in configured with a static IP. If so, then there is another issure which is that whenever I try to change it from static to automatic/dynamic IP, the page fails and the router doesn't even get connected to the configuraion page(192.168.1.245) after that. The only way to get that page again is the reset the router.
Also I'm not able to directly get into the config page when I connect my router to my laptop via lan. I need to change the LAN IP to 192.168.1.x where x is >1.
I'm essentially looking to extend an existing network in a primary warehouse for our company across a parking lot to a secondary warehouse with no network drops. I need to keep the ability to assign addresses in the existing scheme over to two computers in the secondary warehouse.
View 1 Replies View RelatedMy son ran some program that he didn't know what he was doing and now there is no Network access. As far as I know this is what caused the problem, but I'm not certain. When I tried to reinstall the drivers an errors pops up stating that the drivers couldn't be installed due to "Invalid Access To Memory Location". The networking card is an Intel 82566DC-2 Gigabit Network Connection Adapter. The Networking card is part of the Motherboard. I have the original drivers but they will not install due to the "Invalid Access To Memory Location". Anyhow my son went and bought a new networking card, and it gives the exact same error. I tried uninstalling the networking card in the device manager, but when the hardware is reinstalled, and the drivers are about to install it gives the same error. computer is a Dell XPS 420 with 6 gigs of RAM, an Intel Core 2 Quad CPU Q6600@2.40GHz Also in the Device Manager everything under the Heading Network Adapters has a Yellow Triangle with an Exclamation mark in it. I know that this means that there is an error somewhere. I also want to add that when I checked the Netgear GA311 Network adapter card (this is the new card that my son bought)in the Device Manager it says This Device is not working properly because windows cannot load the drivers required for this device (code 31).
View 9 Replies View RelatedI have an Aironet 1250 AIR-LAP1252AG-A-K9 I am having issues with, and I am hoping for some direction on how to resolve them. I understand this question has been posted many times many different ways, but i have no luck unfortunately. Here is where I am: I can terminal into the AP, which has been set to factory default, with the username and password and enable password of Cisco. Once I am in the enable mode, I get lost.
Usually there would be an option to go to config. t, and work from there, but this AP does not have that option, Actually if I do a ? at the enable prompt, the commands list only starts with the letter C; but none are config.
I also cannot get into the web interface of the AP. The AP gets a DHCP IP from my DHCP server, (192.1681.128/24) but I cannot get into the web interface using the IP it gets from DHCP. The page never comes up. To add to the confusion, I cannot turn off the CLI event logging, although I enter the command "no debug all". Maybe I am off on what to put in. Nonetheless, it drives me crazy with messages every two seconds as I am trying to type while attempting to figure things out.
Overall, from reading the forums and doing Google searches, I am going on the assumption that the AP is now in lightweight mode, as opposed to autonomous mode, which is where I want it to be. I have tried the method of updating the firmware to the autonomous firmware from Jan 2013 for the AP. I use the TFTP method as I have found here on the forums a few times; I hold the mode button down while applying power to the AP, let the system LED turn red and release the button so the TFTP process can go through, but nothing changes.
I have the AP powered from a gigabit POE switch. The computer I am using for the TFTP is on the same sub net as the AP. I have tried using 10.0.0.6/24 for the computer with the TFTP on it, made sure the view all file extensions option was checked, and renamed the firmware to the .default extension-still nothing updates.
I also noticed that once I hold the mode button down for 20-30 seconds then let it go, the CLI output says the AP it is on the 10.0.0.x sub net, but I cannot ping the computer with the TFTP program on it. If i try to, it get a "Command not supported" message. So I will go on the idea that this is most likely why I cannot do a TFTP update.
About 30 seconds after I release the mode button and the AP boots, it will say it has a 10.0.0.x IP address, then it starts going crazy with messages that it cannot find a DHCP server.
What I want to do is the opposite of most configurations. I live on a small island with only one DSL connection. The modem is wired connected to a WAP54G Access point. To extend this access point want to use a WRT54G.
View 4 Replies View RelatedI'm using a WRT120N and have had no problems connecting most wireless devices, but a Nintendo DS and DSi owned by my family are unable to connect to the access point. My wireless security mode is disabled, network mode is set to mixed, SSID is the same as on the DS/DSi, Channel width is 20Mhz only, Standard channel is set to 6, but I tried using channel 1 and 11 without success, SSID broadcast is enabled.
I've tried every work-about I could find and always get the 51300 error code, and am at a loss as to what else I can try to get the devices to connect to the access point.
Is it possible to configure WRT120n as an access point?
View 1 Replies View RelatedI have 3 E3000 Routers and would quality input regarding using 1 of the E3000 Routers connected to my Broadband Modem (Roadrunner) and would like to know how to configure the remaining 2 E3000 Routers to be hardwired to my main Router as Access Points located approximate segmented 1/3rd areas throughout my house which really is only 1800 Sq.Ft. in area. How to be configure these routers as access points as well as configuring the main router that will be connected to my broadband router. This is my first network to utilize streaming video, Internet Television Programs, Internet Radio, Accessing the Internet in all rooms of my house and outside the immediate adjacent patio area.
View 1 Replies View RelatedI have tried to find mib for my Linksys WAP54G acces point without succeed. Any body know how I could find it?? I want to program a software based on SNMP protocol. Is there some databses for mibs?
View 1 Replies View RelatedMain Site allows communication from Remote Site via VPN to Windows ServerMain Site also has a secondary subnet that communicates ONLY through internet but NOT to the Windows Server.Sonicwall 192.168.168.x is main siteRemote Site is 192.168.0.x connecting to Main Site to access shared folders on serverSecondary subnet at Main Site is 192.168.0.x using Windows XP PC's. They are accessing a linux server at 192.168.0.215 which Main Site has no access to.VPN remote ip's are 192.168.0.x - they can successfully access the Windows Server at 192.168.168.100 BUT NOT 192.168.0.215.GOAL: Want to connect Remote Site to Secondary subnetWilling to make router changes or whatever is necessary to get Remote Site to access Secondary Subnet with the only exception that the Secondary Subnet REMAINS.VPN DHCP is turned off but willing to turn it on.Willing to make the Linux Server 'discoverable' on the Windows Server. Don't know linux at all but another co-worker set it up and can make changes.
View 4 Replies View RelatedOur company has a Server in the office to which we all map network drives.This server is backed up to a Cloud Server (egnyte.com). Whenever I am working on a database on the mapped network drive, it freezes up after 5-10 minutes with the alert "Your network access was interrupted.To continue, close the database,and then open it again."
This problem does not occur with any other Office Products,only Access.It happens to all databases on the server and to all users.
It does not do this when the file is saved on my desktop or when I am working on it directly through the cloud server. When working on the cloud server, however, I went to Compact and Repair my database and a window came up saying the file location did not exist and my whole database disappeared. It was already saved in the file location, I was just compacting and repairing.
Is there some problem with using a local server that backs up to a cloud that makes it lose connectivity every few minutes? Why is this only happening with Access?
I have successfully setup the AnyConnect VPN (connecting to our ASA5510) and have split tunneling configured. My remote users can access inside LAN servers as well as the Internet from their remote location. What I would like to know is is it possible to change the split tunnel and not allow access to the Internet from the remote location but force the remote client to go through the VPN and out our internal edge firewall to the Internet? Basically I need my remote clients to access the Internet but I would like for their Internet traffic to go through the VPN and out our edge firewall. This will allow the same security as if they were sitting in the office.
View 4 Replies View RelatedCannot access configuration page for WAP11 Access
View 9 Replies View RelatedI have two SSIDs on an Autonomous Access Point, that goes to a 2960 switch, that connects to a L3 3560. I have a vlan for admin/private internal access that uses the native vlan (1) and guest vlan (50). I have configured both and I am trying to get both to go out the same Internet connection.
I cannot get the guest access to access the Internet. It looks like my computer will go, but it just comes up saying no Internet access.All interfaces are trunking this vlan properly. I can communicate from the laptop to the 3560 but I just can't get to the Internet.
I'm having some difficulties with the VLAN setup on the SG-200 and the WiFi access point. The access point (a TP-Link WA801N) is only able to access the internet when it is plugged into a port that is on the default VLAN (PVID 1). If I plug it into one of the other VLANs then any clients connected to the WiFi lose access to the internet and cannot access devices on the VLAN. I have previously used this setup with a first generation Cisco WAP4410N. [code]
View 4 Replies View RelatedI have a 5500 controller that we use to manage our lightweight access-points. We have had complaints that the 'guest' vlan in the boardroom is not usable. Our guest vlan is in fact overloaded.
I went back to the original site survey and noticed that coverage for the room is not ideal so I would like to have a new lightweight access-point installed in the boardroom and somehow limit the access to it to only a few people.