ICS Dependency Service Does Not Exist Or Has Been Marked For Deletion
Jan 16, 2012
Let me try to give as much info as I can to start. Running Windows 7 64bit Ultimate have all updates as of 01-16-2012. Recently had some malware that I removed not sure if there is a correlation. I am trying to connect my wireless connection on my pc to a router to run xbox and BD player. So I connect to my wireless network have my network card plugged into my router, connected to both networks. I go to properties on wireless connection click sharing tab check allow other network users to connect to the internet through this computer connection, also checked allow other network users to control or disable the shared internet connection. I click ok and get a error window that says in the title bar Network Connections the body of the window says, "An error occurred while Internet Connection Sharing was being enabled. The dependency service does not exist or has been marked for deletion. I looked through services and device manager in non pnp drivers everything looks right to me... I am not super familiar with networking issues so I may have missed or overlooked something easily.
we use FWSM , users getting connection refused while they try to connect to destination server. User subnet allowed in firewall to access the server with no port restrictions. when i see in firewall logs, i see belwo error message for source usersubnet and destination server %FWSM-6-106028: Deny TCP (Connection marked for Deletion)
My connection status icon has a big red x on it. I can't get on the internet. I tried the cmd stuff( ipconfig,netsh renewand release, and all the other jazz to do) my ip address starts with a 169 # I know that's not good. I go into my networks and I have no network. I go into my LAN ip4 and ip6and there are no addresses no were.I checked the LAN area status and it says not connected.
I've been working on my laptop recently, once finished i turned my computer off like most people do. After turning it back on hours later, i noticed that my laptop was connected to the internet router but had limited access which ment i could'nt get onto the internet ! So when I went onto Network and sharing center and nothing came up apart from ''the dependency service or group failed to start'' ...I don't want to use system restore or reset tools of windows
DHCP Client and Network Location Awareness aren't working. When I tried to start DHCP Client, I got Windows could not start the DHCP Client service on the Local Computer.Error 5: Access is denied. I checked the dependencies and all of them were on. For Network Location Awareness, I got the error Windows could not start the Network Location Awareness on Local Computer. For more information, review the System Event Log. If this is a non-Microsoft service, contact the service cendor, and refer to service-specific error code -1073741288. One of its dependencies is fine, but I don't know how to check the other two, Ancillary Function Driver for Winsock and NetIO Legacy TDI Support Driver. Also, how do I check the event log?Everything on the list that was said to check is running expect these two the lisie was having problems with. I have not had anything with memory recently and have not been able to successfully go through a system restore. I have tried many of the suggestions and just am not sure what to do anymore. The computer works perfectly fine, minus it cannot get on the internet.
My roommate and I are trying to set up the internet, but my computer won't detect the Ethernet Cable. Whenever I go to Network and Sharing Center and try connecting to the internet, the computer simply says "Windows did not detect any networking hardware", even though the light is clearly on and should be working. The cable is also new so it should be fine. I've also been looking around on the internet a bit, and in trying to fix the problem it looks like some of my Services are turned off, which seems to be causing the problem. However, whenever I try and turn them on, I get an error message saying "The dependency service or group failed to start".
I could not find any report in ACS 5.3 which gives details on user creation and deletion in ACS. This feature was there in ACS 4.x but it seems not provided in 5.3 version.
I am working on Nexus 7010 with NX-OS 5.1.5. I have to delete the static route 10.10.0.0/16 via 10.16.0.21. [code] I try to remove the route with the command "no ip route 10.10.0.0/16 10.16.0.21" and I have the message below % Route not deleted, it does not exist..I don't understand why I have this message because the static route exist.
I have a d link dir 615 "ipv6 ready". My internet provider give tome a native ipv6 /48. I configure the router with my ipv6 /48 address the internal propagation of the address is good.
On the status ipv6 page all seems OK marked "connected" but I can't have an ipv6real connection and my provider say to me that i am not connected.
Is there a known problem of connection between an public /48 and the internal /64 and if so could it be corrected.
1. Any reason COS 3 is not marked outbound on this traffic? I'm determining this by doing a wireshark off of interface g8/1. The traffic appears to be marked on the ingress correctly but does not maintain its mark on the egress. I can confirm this with equipment on other Ethernet links in produciton as well as my test port listed in the config below with wireshark.
FYI: Unfortunately with my cards in the 6509 I cannot port mirror and see outbound multicast (determined through a TAC case). Because the STB does not understand tagged traffic I setup the native vlan for it to function. To see the multicast with tags I temporarily remove the native command and do the wireshark to see the multicast. It still shows a COS setting of 0. I will try to attach a capture of a multicast packet.
We tested a QoS in a Cisco 3750E, IOS: 12.2(58)SE2.Voice traffice in the correct Q without any problem, but all the others traffic the Defualt Q (0), tried to capture the traffic and tcp/udp port are correct.Any thing wrong with my ACL or DSCP - CoS?? ( that ACL works fin on 4500 and 6500) [code]
I ran into this recently with a client of mine. When uploading files (either via FTP or through a shared drive in terminal services) from the site any files larger than 200MB or so would hang in the middle of the upload as the TCP session timed out because the traffic was cut off. I started pulling apart the config on the 2911 edge router to determine what the issue was.
I trace the issue down to this particular policy which was created by CCP: sdmappfwp2p_CCP_LOW (When this policy was removed from the wan interface the issue vanished). The default config of this policy was as follows:
policy-map sdmappfwp2p_CCP_LOW class sdm_p2p_edonkey drop class sdm_p2p_gnutella drop class sdm_p2p_kazaa drop class sdm_p2p_bittorrent drop
I first removed the highlighted drop command from the edonkey class and reapplied the inspection policy to the WAN port and the issue remained resolved!
While this fixed the issue and I was able to block eDonkey traffic with just a simple outgoing ACL to block tcp port 4662 I find it very strange that a eDonkey inspection policy would cause such problems for eDonkey traffic. I know for sure this is the only change made on the router and I'm just scratching my head at what I've found. Is it a bug with NBAR? Mostly I'm just curious as the issue is already resolved.
When I create a service object or group and add the object to a new rule it never works.I mean the traffic match not the rule. I see not hits.I placed the rule on top of my access list to check if I do somethink wrong but it is not working. When I place only a service for example tcp/23 it is working.
We have a situation where services are stopped on the real servers. The probes fail and we confirm the services are not running on the server. We cannot access the ports from the ACE directly. We can still however acces the VIP on the TCP port (L4 VIP class-map). So we can still telnet to the VIP on the port from thr Client side of the network.This is on ACE 20 Modules deployed in Routed mode. The version of software is A2(3.3).
Tried removing multi-match and loadbalance policies as well as class-map and re-applying then re-appyling the service policy to interface. Same behavior,This is a problem at another level as some services are being monitored by GSS via TCP keep-Alive and this obviuosly causes a problem as the service then never goes off-line.
I have a fresh installation of LMS 4.0 on windows server 2003, when i click to open topology i get error message : ANIServer service may be down or Host name isn't DNS resolvable
i tried pdshow -brief ANIServer ===> service UP
DNS is working using host file in driversetc i restarted the server
Everyone speaks about video and music streaming, however I am under the understanding that there isint actually any such thing as legitimate real time streaming, ALL files are saved to the disk or the RAM. If this was not the case, disrupting your Internet connection would cause an instantaneous crash of the streaming media, and well, I have had my Internet crash a lot of times while viewing streaming median and in every case it continued to play for some time.
a have a router CISCO 1841 and I configured a NAT inside from the router to the firewall like this :ip nat inside source static firewall_adresse public_adresse and its work fine and when a added it I do this command "wr" to save the configuration and I restarted the router many times and it still work fine,but in the last five months this NAT does not exsit twice and I must add it a gain.
I've got a LAN set up with a server and printer, no internet connectivity to it. When I need to access the internet, I connect through a wireless hotspot. The only problem is that I have to unplug the ethernet from my LAN connection for the wireless to work.Is there a way to have both connections coexist, so that when I need to print something or access a file on my server I can do so without it interfering with my internet connection?
I know my Modem/router is old but I am connecting okay to the internet with my laptop, the thing is my husband has just bought a Google Nexus Tablet and although it finds my Belkin Modem (model F5D7632-4) it says it's finding IP address, then says its saved and then connecting, but it dont connect. Also there is no security on it and it wont find my model number to add the security, is it me or what?
Is there a limitation to the amount of sub-interfaces that can exist on a Cisco 6509? The switch has WS-SUP720-3B (Sup card), WS-X6724-SFP (linecard), and 12.2(33)SXH7 (IOS).
I am using ASA 5520 Image in GNS3, when i come in Configuration Mode and try to create Tunnel through command "interface Tunnel 0", but this command doesn't exist. I need this command to create Tunnel for GRE Lab.
so far i also knew that if u assign an access-list to an interface:
for example: int vlan1 ip access-group 150 in
and the access-list does not exist in the configuration it will block everything meaning it will be an implicit deny empty access-list but lately i've noticed on new routers that its different,if i assign an acl to an interface where the acl doesnt exist in the configuration it acts as permit all,
How to connect my Windows XP Desktop to my homes wireless network system (my comp is outdated I know ). I have no trouble with my my mum's Windows 7 Laptop and no problems with my MacBook Pro, but how do I connect this old clunky XP to it?
Wireless Connections doesn't exist in my network connections tab, and in Services under Admin Tool - in the 'Wireless Zero Configuration Properties' is set to Automatic startup type and it is 'started'.
I have created a VPN client account on my RVS4000 router. I have installed Quick VPN on my laptop in the default directory -- Program Files (x86) / Cisco Small Business / Quick VPN Client
I have generated and exported a certificate -- RVS4000_Client.pem -- and placed that in the Program Files (x86) / Cisco Small Business / Quick VPN Client directory. When I attempt to connect using the Quick VPN client, I get the warning "Server's certificate doesn't exist on your local computer."
If I ignore the message I can log in, and ping resources inside the network and log into the router. However, I cannot mount any drives and the router shows that no VPN tunnels exist. I've read several posts here and elsewhere and can't seem to see where I've gone wrong.
Our company has a Server in the office to which we all map network drives.This server is backed up to a Cloud Server (egnyte.com). Whenever I am working on a database on the mapped network drive, it freezes up after 5-10 minutes with the alert "Your network access was interrupted.To continue, close the database,and then open it again."
This problem does not occur with any other Office Products,only Access.It happens to all databases on the server and to all users.
It does not do this when the file is saved on my desktop or when I am working on it directly through the cloud server. When working on the cloud server, however, I went to Compact and Repair my database and a window came up saying the file location did not exist and my whole database disappeared. It was already saved in the file location, I was just compacting and repairing.
Is there some problem with using a local server that backs up to a cloud that makes it lose connectivity every few minutes? Why is this only happening with Access?
EA4500 router setting currently I am on an single fix IPs network, Internet access filtering by a Fortigate gateway, some IPs has Internet access, most of the IPs without, and we like to keep it that way.may I know what is the proper way to configure the newly added EA4500 router to working with "Guest Access" and my existing fix IPs network?
I have been playing with multicasting on my home network and have hit a problem in that all multicast messages seem to be spewing out over the WIFI regardless of whether there any any subscribers present or not which is swamping all other WIFI traffic. The wired LAN seems to be behaving just fine (no traffic on the wired network if no subscribers present).
how do I filter the multicast messages so that they are not sent out over the WIFI (unless a WIFI subscriber is present)? I have tried enabling the IGMP proxy but it makes no difference. I've tried messing with lots of other parameters too but no joy. Does multicast filtering actually work (or exist) on the WAG320N?
I have an AIR-LAP1242AG-A-K9. Straight out of the box I thought it would have the GUI functional but this is not the case. I am brand new to Cisco products so it is taking me a while to get use to them and to TelNet but from what I have read in about 6 different manuals none have explained how I can access the configure terminal command when It doesn't show up. I am in privileged mode with access of: AP001c.588e.a266#show privilege. Current privilege level is 15.If I can't get into global configuration mode I cant enable the GUI, turn on the wireless.
I'm setting up a couple 881W cisco routers to use Unified wireless and am running into a bit of a brick wall.I've read through the "Upgrading to Unified Cisco Software" section of the following article:[URL]The problem is, I can't run the "service-module wlan-ap0 bootimage unified" command. The keyword "bootimage" does not exist. The router is licensed for advipservices and I'm running version 15.0(1)M4 on the router. AP is currently running version 12.4(21a)JA1. why the bootimage command doesn't appear? Will I need to downgrade the router IOS to 12.4?Additionally I'm having trouble finding an answer to the following:Is there a way to set up the embedded AP on the same network as the Data VLAN on the router, or do I need to create a separate IP network for the embedded AP? I've tried using 'ip unnumbered vlan10' (vlan10 is the data vlan) on the wlan-ap0 interface but then when I try opening a session to the AP it doesn't connect.
-Model : TL-WR1043ND -Hardware Version : v1 -Firmware Version : 120605
I'm wondering if USB HDD spin down capability does exist on the deviceI think this enhancement will be serve a lot of costumers who wish to use all USB features.