I planning a wireless home network and would like to have WiFi internet access at my swimming pool ~150 feet from the house. There is only one wall between the location of the wireless router and the pool. Do all routers have similar range? If not what is a good model for this range, or would I need to add a range extender?
View 3 RepliesI have two Dir-655's - router1 and router2.
Router1:
ip 192.168.0.1
subnet 255.255.255.0
DHCP enabled range = 192.168.0.100 to 192.168.0.200
Router 2:
ip 192.168.0.2
subnet 255.255.255.0
DHCP disabled
Routers are connected to each other via LAN ports with a switch in between.Both routers have the same wireless SSID with the same password. I am able to connect wirelessly to both routers no problem.
I have a machine running a shared iTunes library which has a wired connection to router1. I also have an Apple TV wired to router2. My issue is if I am connected wirelessly to router2 I may or may not be able to connect to iTunes library. Conversely, if I am connected wirelessly to router1 I may or may not be able to play content from iTunes to Apple TV. I cannot figure out why everything works fine sometimes yet at other times I cannot connect devices between the two routers.
Can I set up n600 db F9K1102v1 as wifi range extender with no rj45 cable?
Dont have cable infrastructure in section of building where i need net access.
Have a Cable/Modem (wireless) as main router and need to extend the signal using the N600DB - but without cat5 cable between modem/router & N600.
I have a 3 story townhouse and want to have one n600 connected to my modem on the 3rd floor and then have the other downstairs connected through wireless to the one upstairs. I have seen lyncsys will do this but will the belkins?
View 1 Replies View RelatedI have decided to buy belkin n600 router. my question is can i connect Belkin wireless range extender n300 to belkin n 600 for beater coverage. is this possible ? if possible how many extender i can connect to the router and also can i connect extender with wire and wireless.
View 12 Replies View RelatedDoes the Dual-Band Wireless Range Extender #F9K1106 work with the Apple AirPort Extreme Base Station?
View 1 Replies View RelatedI have a Buffalo NAS with IP address 192.168.1.30 linked to my router, which has IP address 192.168.2.1. Both have the same subnet mask: 255.255.255.0.DHCP on the router assigns IP's to my computers on the network (192.168.1.xxx). How do I access my NAS?
View 3 Replies View Relatedi have 13 acre and wanted to know about using a security camera set up wireless,solar power IR motion sensor type set up??
View 1 Replies View RelatedI have a Belkin F6D4230-4 Enhanced N150 router. Would it be advisable to add a range extender to hit weak signal areas or simply upgrade to a more powerful router?
View 1 Replies View RelatedI have a supplier which i need to connect a site to site ipsec vpn connection to (from a draytek router). I have already done this on our main site with no problems using the local ip details of 192.168.1.0 and subnet 255.255.255.0 however i need to do the same on our DR site which uses the ip details of 10.1.0.0 and subnet of 255.255.0.0. Our supplier told me the 255.255.0.0 is already used at there end by a different customer so we are unable to connect the vpn and communicate (in theroy we can connect but our supplier cannot reply). We can setup a connection to another spare server on a different address using a different subnet but effectivly this would mean that communication would stop at that server and communcation to the overall network or specific server the supplier needs access to (on the 10.1.0.0 255.255.0.0 network) is not possible. I was thinking maybe an internal vpn server to server connection through win server may do it, 2 nic cards or routes in the server routing table but this all seems a bit messy. Our network consits of win 2003 and 2008 R2 servers and is basic network with modem-vpnfirewall-switch and devices on the internal network connecting to the switch.
View 5 Replies View RelatedAlthough I haven't looked through all the forum topics I couldn't find anything very similar to my situation. I have a rather large house and my modem/router (Netgear DGND3300 v2 due to DSL) is in the very corner. Given this most of the opposite corner of my house gets either poor or no connection; however, I do have an ethernet cable run across the house through the basement to my home theatre setup. This is where I encounter another problem, I need multiple devices to be connected via ethernet and I also need to have wireless in that same area. In my mind I picture myself connecting a second router to this ethernet cable through which I could have wired connections to all my devices, and a second router broadcasting wirelessly. I'm familiar with some types of wireless bridging, but I'd rather use more of a wired bridge concept if possible, but I've never really seen something like this. The question is, is this possible? Or, what is another possible way to achieve the same results? The only other thing I can think of is to run an ethernet hub from the original wired connection to my home theatre so I can connect multiple ethernet devices and run a separate wireless extender or something, but this just seems pricy.
View 2 Replies View RelatedCan I connect a Belkin N450 wireless router to a Belkin N750 wireless router without using a cat5e cable?
View 1 Replies View RelatedI have a Belkin NF5D8236-4 v3 as my main router. However, the signal range isn't the best throughout my home. After a little research and a tight budget, my thought is to purchase a Belkin N150 F9K1001 to serve as the primary router and then use the N F5D8236-4 v3 as an access point elsewhere in the house.I understand that the N150 cannot serve as an access point (hence the idea to use that as the primary), but that the N F5D8236-4 v3 can. Am I correct? Will my plan work? I can't spend much and a booster would cost more than the N150.
View 1 Replies View RelatedI have a N300 router I would like to put in another part of my house to repeat the signal from my N600 at the other end of the house. Is this possible? If so, how do I set up the N300?
View 2 Replies View RelatedI just purchased the Belkin Range Extender F9K1106 - During set up I am suppose to go to a website belkin.range - the site does not work or exist. I am unable to complete set up now.
View 1 Replies View RelatedCan N600 DB Wi-Fi Range Extender have the exact same name as my N600 DB Router or does the extender have to have the additional characters "_xt" at the end of the extender name, when the first part matches the router name?
View 1 Replies View RelatedI have a Netgear N900 WDR4500 Dual Bank Router. Which range extender should I use for the best result?
View 1 Replies View RelatedI am new to the RV180W. I am running the most recent firmware--version 1.0.1.9.
I am having trouble getting FTP to work with my QNAP NAS.
QNAP indicates that I should forward ports 55536-56559 to my NAS. I created a custom service to accomplish this, and then, under port forwarding, I selected the service and forwarded it to the private IP that corresponds with the NAS.
However, the port forwarding configuration only allows me to specify *ONE* internal port. With other routers I have always specified the same private port *RANGE* that corresponds with the public ports that I have opened up.
I am trying to add a couple VOIP phone units that do not have their own router. They are designed to run of the existing router and have three ranges of UDP ports opened up. They also do not advise using internal (private) statics on the phones. So what they are asking for is three different ranges of UDP ports to be opened up to all behind the router?
I cannot figure out how to do this (or if it is possible) with a RV016.
How can one forward a range of ports?
Suppose I have defined the following service:
Service: TEST
Port type: UDP
Starting port: 5060
Ending port: 5070
and I want to forward it to a specific IP. Then, if I create a new port forwarding rule for this service it asks me to specify a single port number to be used internally as:
Action: Always Allow
Service: TEST
Source IP: Any
Destination IP: 10.0.0.100
Internal Port: ?
I want to forward all ports from 5060 to 5070 to the internal range 5060 to 5070.
I am not a tech guy but have to take care of some basic IT stuff. I had Ether fast cable/DSL router and it got changed with RV 120W router. there were comment that internet is now working slowly - what could be the reason for this?
I copied most of settings. First big technical problem was with phone. It stopped working - call could get through but when answered there was no sound. We use linksys modem for VoIP. I called operator and was told to disable sip alg. I did that and service improved a little. When answering a call sound could get through but would stop for few moments and then continue. Operator told me to forward port 16384 to 16482 to VoIP modem IP. But I can only set forwarding for one port at the time in "Port forwarding" settings. Is there a way to forward to port range?
I have a SRP547W which I'm trying to replicate a configuration I had on an old Cisco 847 that recently died.
My ISP has allocated me a /29. The DSL configuration means that the IP address on the PPP session is assigned randomly. I have a mix of internal devices on a private IP range and a few devices with publically accessible addresses. All of the devices on the internal network need to be NATted to a public IP from the range allocated to me.
I can see that I can use the software or hardware DMZ to set up the servers, but I can't see any way to configure the external NAT address.
Any solution for NAT only for a specific ip address or a range of ip addresses from the same subnet?
I've read that the router in gateway mode automatically makes the translation and in router mode does not. Starting from this, is there any way to nat from firewall access rules only.
I am trying to Port Forward HTTP: 80, but my Router wont let me and it keep giving me this error message Status: Port Range Overlap with Remote Management.I have a NETGEAR CG814GCMR Router, I need to add that port for setting up a Game private server online, but my router wont let me, how to fix it?
View 12 Replies View Relatedhow do i connect two wifi routers to increase the range. One router is a cisco WRT120n and the other router is a d-link DIR524..
View 1 Replies View RelatedWhen trying to update the firmware on my range extender, 192.168.2.1 does not work (per instruction page). When I found my default gateway address, it wanted me to login to my Netgear router -- not to the Belkin extender to which it's currently hard connected. F9K1106V1
View 2 Replies View RelatedI have a Belkin N300 Dual-Band Wi-Fi Range Extender but the signal light is always amber and I have difficulty connecting to the N300 wi-fi. Can I use a wired Ethernet cable to connect to it rather than it picking up the existing weak Wi-Fi signal?
View 1 Replies View RelatedI have read through the manual. My question is what is the proper format to input into the ACL rule "Range"? Would as an example work- 192.168.0.1 - 192.169.255.254? Will the range effectively work? Or does it have to be 192.168.0.0 - 192.169.255.255?
View 7 Replies View RelatedMy F9K1106 range extender (brand new out of the box) will not connect to my router. I have an ASUS RT-N66U router. The Belkin extender keeps telling me the password to the router (WPA2 security) is incorrect. Every other device (bridges, computers, tablets, mobile phones) connects to the router perfectly with the given password.
View 7 Replies View RelatedI have a N600DB configured as a primary router. I got another playmax n600HD router which I want to configure as an access point that extends my network upstairs and allows me to attach some wired devices like my ps3. I followed the basic principles of setting as access point and my locally connected ps3 and NAS are communicating but no Internet access. How the 2nd router can connect to the internet?
View 2 Replies View RelatedI just connect my new EA 6500 router and I am trying to connect my Belkin F9K1106 Range extender to the 5Ghz and it keeps saying the password is incorrect. I am able to connect to the router using 2.4Ghz with the same password. I have updated the extender's firmware to 1.00.16 and it didn't work.
View 10 Replies View RelatedI have a WN3000RP WiFi Range Extender but I cannot seem to find out how to connect to it on my Windows 7 Desktop computer to configure it. My Router is a Netgear Wireless G RouterWGR614 v9
View 7 Replies View RelatedI am having problem using the N300 dual-Ban Wi-Fi Range extender with my att 2wire 3800HGV-B router. Cannot use the extender to access the internet. The Att router works without it. Just want to use the extender to extend my att router signal but cannot.
View 3 Replies View Related