I've had the Netgear Rangemax WNV111v2 for over 2 years, and it's stopped working about 3 days ago.I can connect to my internet, but only lasts 30 seconds - 1 minute, after that my network settings tell me that I can connect to my modem/router but not the internet, and all of the other computers in my house are working just fine, and are all connected to the internet.
View 1 RepliesI just re-installed Windows XP Pro on my desktop. It used to have Windows 7. I used to access internet wirelessly on Win7 with this Netgear WN111v2 adapter. So the adapter is in working condition.
So I put the drivers (tried both version 3.0 and 3.1) on a USB key and installed them on that desktop.The installation went fine, the program runs fine. It can even identify wireless networks around my house.
I chose my wireless network, entered WEP passphrase and it connected. Then in the bottom right side of my screen there is a little commputer and a yellow dot is moving next to it and if I hover over it is says "Acquiring network address".
Here is what I see when I type ipconfig /all :
Quote:
Microsoft Windows XP [Version 5.1.2600]
(C) Copyright 1985-2001 Microsoft Corp.
C:Documents and SettingsALESS>ipconfig /all
Windows IP Configuration
[Code].....
I recently bought a second hand in the package netgear maxrange wpn824 router, and it requires a 2.4 ghz 802.11 b/g wireless adapter and windows 98. I have a gateway laptop, operating system windows vista home premium oemact, model: md2614u and it has a ralink 802.11n wireless LAN card. Can I install and operate the wireless router even if I had diferent wireless LAN card?
View 2 Replies View RelatedI need to open the 443 port on my rangemax wireless router to enable credit card processing
View 1 Replies View RelatedI am using a Netgear Rangemax Wpn824 with comcast cable internet. This problem happened also on an older router but less frequent with this one.
I don't know if this is a common problem but I cannot seem to find it on the web and thought I would ask here. The problem seems to only happen after someone restarts their computer.
What happens is 9/10 times on startup the internet will connect just fine but the 10% of the time it will say "Unable to connect to Shaun" (my wireless router) Sometimes if we restart the computer it will fix itself but usually we have to reset the router and it will fix itself and wont happen again for another couple of weeks.
I called comcast about it and their tech support said it was a router issue, that's when I put in my newer one (the rangemax) and its still happening. We even upgraded the comcast modem recently too, and since it fixes itself when I reset the router I don't doubt its the router.
I can't seem to update the firmware on it, not sure if that will work. (It says not enough memory to complete) Should I buy a new router?
I have a USB Netgear WN111v2 that has been working perfectly up until now, it can't connect to the network and trying to manually set up the addresses, reinstalling drivers, and trying a system restore haven't worked. Even though the router has a lease for the computer on 192.168.1.11 it's doesn't work, although it will show that it's connecting, it won't ping anything, including the router... WZC utility is stopped?
View 4 Replies View RelatedI an on this form from my cell right now.. so, the computer i want to get Online with is a desktop and i have been days with this problem.
View 14 Replies View RelatedXP Home edition, went to tools can't find working off line or working online to make sure off line is not checked so I can get on line DSL Verizon , Wireless router, wireless switch in on, on the cpu
View 1 Replies View RelatedASUS Notebook G60Vx Series
Windows 7 Home Premium 64-bit
Intel(R) WiFi Link 5100 AGN
A few days ago my internet suddenly stopped working. I plugged in the ethernet cord and everything worked fine. Checking the properties in the device manager showed the device was working properly, I also tried resetting it to make sure it was enabled but it did not work.
Upon troubleshooting, the "Windows Network Diagnostic" said the problems was that the Wireless adapter was not turned on. Using the switch on the front of the laptop as well as the function keys does nothing. Usually a graphic pops up showing if the WiFi is on or off, changinging transparent to show the WiFi is disabled. Now when I turn the switch on it always appears transparent, effectively going from off to off
So I know the computer reads both the function keys and the switch on the front but both methods never actually turns the adapter on. I just finished a system restore and nothing has changed
Today, while surfing the web my internet connection on my PC just randomly shuts off. I go check on my laptop and its normal. My WiFi says that I am connected to an Unidentified network with no internet access. So i got frustrated and checked all the forums and nothing seemed to work. So i restored my computer to factory settings and I still got this problem. Does this mean my Wifi Card is bad? Is it a virus? I can see other networks fine but i just cant connect to mine!
View 8 Replies View RelatedWe create a LAN with D Link switch(8 port).6 pc working properly and 1 pc even not connected to LAN we check wire,the signal are transmitted properly through wire.Crimping is done properly.
View 1 Replies View Relatedwhat if I don't "have disk"?
View 3 Replies View Related1.SCP Not Working on my Linux Box (Fedora release 7 (Moonshine))to Fedora fc11.i686 running box[CODE]
View 5 Replies View RelatedI have a switch containing 48 connections. I have a patch panel that links to lots of access points in my building. One access point was not connected but needed to be but I didn't have any spare switch ports. I therefore reconnected switch 23 from one position (and thus one access point) to another position on the patch panel. Everything worked fine and this new location had network and internet access. Then however a few weeks later I had to change it back so i changed the connection of port 23 to the old position on the patch panel. When i did so port 23 showed a red light and then no light. Later I had to change it back to the other location but when i did so port 23 now shows no light whatsoever. It's as if the connection port just stopped working. Now both the old and new access point locations have no connection and I can't understand why.I tried rebooting the server but no luck. I tried connecting that access point through the patch panel to a different connection port but still no luck.
View 4 Replies View RelatedMy ISP is sending the signal because my other computers are working and so is my wireless from my router. I just installed XP on my new hard drive. The graphics seem a bit off, but w/e. I tried connecting directly to the modem, and I don't get any sign that I'm connected.
View 1 Replies View RelatedI have 2 PCs connected directly together with a CAT5 crossover cable. I can ping each of them but I cannot ping names of PCs. I have specified IP addresses.My Network Places doesn't show anything in terms of workgroup PCs. I get a cannot access workgroups warning on one of them, may not have administrator privileges etc.
View 15 Replies View RelatedI need to know if I'm right about this. I have a customer that wants me to set up a dynamic-to-static IPsec tunnel between an 1811 router (dynamic) and an ASA with a static address.The catch is that the 1811 sits behind an ISPs cable modem where it picks up a private 192.168.x.x address.
Is there any other way to make this work where the router with the dynamic IP is sitting behind a box that's doing PAT translations?
OK- so my computer was going haywire - freezing, lagging, crashing. Only thing I could do was to restart in safe mode and run a full AVG scan which did show viruses that were sent to virus vault. Once I restarted into normal windows mode, the computer seems to be working fine with no freezing, etc.....but my LAN connection won't work. Looking at all the device managers and info on the LAN - it says "device is working properly". I have tried downloading a few "fix it" programs like Winsockxpfix and Complete Internet Repair - didn't work.
View 12 Replies View Relatedso heres the problem
An error occurred while releasing interface Loopback Pseudo-Interface 1 : The system cannot find the file specified.
Ethernet adapter Local Area Connection 2:
Connection-specific DNS Suffix . :
Autoconfiguration IPv4 Address. . : 169.254.196.232
Subnet Mask . . . . . . . . . . . : 255.255.0.0[code]....
this is a fresh install of win 7
no conection to router or modem, wireless has no problem and the xp box aslo haas no problems
My internet has started to work really slow. I was changing security settings and I think I messed it up.
View 1 Replies View RelatedOnly one LAN connection seems to be working, we have two computers both work only when one of the Ethernet cables is connected to the 4th port on the router. It is only this one that works. The internet and connection works on either but only one can be used at a time, if the ethernet cable from one is connected to any other LAN port than the fourth one there is no connection at all, it reads as unplugged.
I am not even sure when this would have started because up till recently I was using a laptop and didn't worry about a direct ethernet connection however it broke and now we're stuck in this problem.
I've recently been tasked with providing access to several internal servers to a remote site via one of our ASAs. In order to keep things simple, I have begun by creating a single static NAT rule for one of the servers. The Site-to-Site VPN connection profile was then created and testing has begun. Unfortunately it looks as though the NAT rule isn't working. As I monitor the tunnel, I still see our internal number being broadcasted and not the mapped address, which prevents the tunnel from being established. The remote site has verified that this is what they are seeing too.
Appliance:
ASA 5510
ASA 8.4(2)
ASDM 6.4(5)
Address Legend:
(Note: The following addresses are not actual addresses.)
[Code]...
I have been trying to get my FTP server working for months with no joy. It works when I connect to it internally but not from outside. If I do a port scan, I can see that port 21 is open. I tried it with disabled firewalls and also checked with ISP that nothing is being blocked. I have attached the config file. I used several differnet FTP servers such as CoreFTP, Wing FTP etc.
View 13 Replies View RelatedMy desktop model is hp compaq dx2080 mt pc. I am running windows seven.
View 2 Replies View Relatedi changed my laptop from windows 7 home basic 32bit to ultimate 64bit but now the programs in the old windows does not want to install, and i was asking is the anyway i could get the programs from my old windows to work on my new windows? my laptop is a HP 620
View 1 Replies View RelatedI have Westell Ultraline series3 modem/router , the problem is i can only connect to the router/internet if i enter the IP address and DNS manually , which is not much of a problem except I have a vonage phone and can't type the ip address in it , so here's how the settings looks like , let me know what i should be changing
[IMG]file:///C:/Users/GL/Pictures/Network.png[/IMG][IMG]file:///C:/Users/GL/Pictures/Network.png[/IMG]
I am trying to connect a Wii wirelessly to a Linksys router. I keep getting an error code of 53132. Every site I've checked has said that 192.168.1.1 should be the IP used to put into the web address bar and be able to access the settings. Well, it does not work. "Cannot find server" is all I get. I used some suggestions that I found on this forum, and I tried pinging the number, and it times out 4 times. I even reset the router. I have used the numbers for the IP address as written below to try accessing the site as well, and no luck. No number works by placing it after http:// on the browser.Here is the specifics;When I use ipconfig, I get "Ethernet adapter local area connection" "connection-specific DNS Suffix" "Link-local IPv6 Address" (which is approx. 28 characters long-not retyping unless necessary) "IPv4 Address" (which is 24.3.224.140), Default gateway (24.3.224.1); then Tunnel adapter local area connection* 6:
Media state: Media disconnected"
"Connection-specifix DNS Suffix:"
And Tunnel adapter local area connection* 7:
Media state: Media disconnected"
"Connection-specific DNS Suffix:" (which is blank)
[code]...
why the following configuration is not working? I have two clustered ASAs inline from one another, in front of a 4506-E switch in front of a host I want to access via RDP, like so: My issue at this stage lies with getting the UNTRUST firewall configured. I've tried the following configuration 1) Creating the host.
View 13 Replies View Relatedmy wifi is not working
View 1 Replies View RelatedI've got a wireless connection in my house going through a Linksys WRT54GC router and also a wired connection with Cisco gateway (only 1 laptop uses it). About 1 month ago some strange things began to happen with the wireless connection, my PC seems not to be able to connect unless I reinstall the protocols and it's really annoying to do that every time I run my PC. Also, the wired connection stopped working (probably because of cable being broken) but it requires a router restart 90% of the time when I want to connect the laptop (that used to connect through cable) to the wireless network. The 2nd laptop has an issue mentioned in the title, the LAN works but it can't connect to the Internet through the router. Ipconfig /all shows that DHCP isn't working, there's no default gateway and DNS seems to be wrong. Could that all be related to router not being updated for a long time? I tried reinstalling drivers, unistalling and installing back network card and doing most of the things mentioned in similar threads but nothing seems to work.
View 1 Replies View RelatedThe internet was working on and off for a few days but yesterday and now today it has not been working. The router I have connected is fine and the laptops and xbox that I am trying to get internet on connect to the router but will not connect to the internet. The modem is what I believe the problem is however,I am not that great in the networking department. I have a Westell 6100 it is Verizon DSL.
View 1 Replies View RelatedIm having a problem with my wireless. My whole family is connented. to wireless. But when we all use it together it goes so slow. Like 4 some times only 2 people using it at the same time.
View 9 Replies View RelatedMy Wifi internet was working fine 12 hrs ago; now I can only use it with wire.I uninstall 2.0 and install Asus wireless console 3.0 but still not working, Fn+F2 not working either.
[code]...