We have an Asus RT-N56U router at home, which is connected directly to a cable modem. I am attempting to remotely access the router's interface, and am having trouble doing so even after configuring it properly. I configured the router's firewall to allow remote access, using port 8080. I also set up DDNS, although I tried connecting using both the IP and the DDNS name.I also set the router to respond to pings, and I am able to successfully ping the router (from a remote location) using both the DDNS name and the public IP. But when attempting to connect using my browser, it doesn't work. I have tried multiple browsers, multiple remote locations, and disabling my computer's firewall, all with no success.
when my Linux VM is running!How's this for a mystery - last night I noticed that I could no longer access my gmail. Thought it might be down. This morning, I still couldn't access it. Thought I would try comcast, no joy either. Changed computers, no difference. Changed routers, no difference. Bought a new router and started plugging in network cables one at a time. My main machine first, everything works - http and https sites, a second computer, all good. The switch. Fine. Powerline. Still good. Then I plug in a Windows server running a Linux VM. Https sites on all the other machines stop working. Pause the Linux VM, restart router - https sites return to life. Went to Linux machine, re-enabled ipv6 (the only recent change on the Linux machine was to disable ipv6 since upon a reboot, Linux didn't have an ipv4 address). Restart Linux everything seems fine. A few hours go by, try to connect my wife's new laptop and at that moment wireless seems to stop. Restart router, wireless is back. But lo and behold, https is gone again. Unplug the machine that has the Linux VM, restart router, all is good.Ever see anything this weird?
I have a flashed Asus RT-N12B1 that was working but now has ceased working I am trying to get the info from the router using 192.168.1.1 ;but cannot get that working . I need to access the control panel in the router to change some parameters . To do that I have to access 192.168.1.1 .Safari does not allow me to do this .
3 times in the last 2 hours i have had my new rt-n56u give me the message.You have set the wrong dynamic or static IP address for your RT-N56U.
So i reset the router and it pulls the same IP and info it had before from my ISP.Doing some reading it seems some people have had this issue occur over and over.I am upgrading to the new Asus126.96.36.199i from 188.8.131.52f which is installed now, but wanted to ask if i have other options for this router as this problem gets annoying..Example i am used to DD-WRT for my linksys wrt- models..does the NT56U have something similar...
I have had the Asus working with a netgear CVG824G(in unison, not bridged) for some time with IP cam & usb media, but no DNS access as running through the netgear gateway. I just upgraded to Optus premium speed pack & received a netgear CG3000 & now can't find the Asus when plugged into CG3000 ethernet port. I have tried to plug it in the same as it was so I could access the asus routers page & change settings to bridge but find nothing. When I try to connect wirelessly to it, the security key is not accepted. Have tried original key and '�dmin'' all with no use. I want it to run bridged to make use of the DNS service with IP cam & attached media
I have the printer hooked up to the USB port on the router (Asus RT-N56U), and in the router GUI, it recognizes the printer but when I set the printer up on my computers, they seem to not want to connect, or if they do it won't print anything for a few minutes after clicking "print." Is this just one printer that's going to have issues printing through the router?
I've tried both USB ports, and a couple different cables.USB flash memory works just fine and is quick, like it's plugged straight into a computer.Ironically, I bought this router to replace my file/print server.
i replaced a lightning damaged Linksys router in my home network with the RT-N56U. My main computer is Win7 64, (Phenom II quad, asus M490GTD) , my wife's computer(wired connection, Dell P5Duo) and my work laptop (wireless connection HP core I5) are XP. I have a USB printer attached to the wife's computer and two wireless Squeezebox receivers. This network worked with the old router. With the new router i can access internet from all computers, and connect to the new network with the Squeezeboxes. I cannot print from the main computer, even though the printer shows up in the devices window and the test page spools.
I've got an Asus RT-N56U router. Attached to the router is a USB hard disk with a bunch of music on it. The music is accessible to devices on my LAN over uPnP/DLNA; this works great. My WAN connection is provisioned at 100 Mbps down / 40 Mbps up. I want to use some of that upstream bandwidth to stream my music to myself wherever I happen to be. I could but don't want to leave a server running on my network 24/7 to accomplish this when the router is already able to share the content locally.
So what I want is some way to make the content that the router is already able to distribute across the LAN accessible over the Internet as well. I've looked around but haven't found any prebuilt solutions to this that don't involve hosting the content on a server behind the router, which I'd like to avoid.
The router does have built-in support for serving up the content over FTP, but I've tried that and found that it really does not play well with media players. It kind of works, but the seek time when switching between tracks is absurd, and some tracks just plain fail.
One thought I've had is serving up the content over HTTP by installing an Apache instance on the router (and/or editing the configuration of the built-in instance that provides the configuration portal, if that's possible?). The router appears to run some trimmed-down version of Linux (I can telnet/ssh into it, it has a filesystem, package manager, and similar things).
I'm trying to connect a Sony Vaio laptop with Windows Vista to my wireless network. It connects to the network just fine but it says "Unidentified network" and I'm unable to surf any websites using any browser. It connects with an ethernet cable just fine and I've already updated the driver for my wireless card.Who is your Internet Service Provider (ISP): Time Warner.What type of Broadband connection are you using: Cable.What is the exact Make and Model of your Modem, Router or Modem/Router Combo: ASUS RT-N56U router / Cisco DPC2100R2 modem.What is the Name of the Anti-Virus, Security or Firewall Software:. [code]
I use to have a DIR-655 and dap-1522 both worked without any issues. I recently upgraded to Asus RT-n56u and now I want to setup the dap-1522 with it.I have no issues with the Asus RT-n56u everything seems to work fine here the problem seems to be with the dap-1522 where it connects but then disconnects almost instantly.
1) Connect dap-1522 with my desktop computer via Ethernet
2) Change the LAN settings for tcp/ip v4 to manual IP
3) I set the manual IP to 192.168.0.60/ subnet mask 255.255.255.0 and the default gateway to 192.168.0.50
4) I open my web browser and connect to 192.168.0.50 and I see the dlink page and I log in fine.
5)I tried going through the wizard, picked manual and have tried both the 2.4ghz and 5.0ghz bands they are set up as WPA-Auto Personal and I enter in my password. It says settings will be saved
6) The page refreshes to the wireless one but I don't see any options here just the save config one. When I go to status sometimes it says its connected but sometimes it just says it's not I try to unplug from my desktop and take it over to where my apple tv is but it never works..One thing I should note is my asus is connected to 192.168.1.X so do I need to change the dap-1522 to 192.168.1.50? instead of 0.50?
I am unable to set router's (RT-N56U) IP adress to default one (192.168.1.1), or any other in subnet 1. It always popum message to me which says "IP adress 192.168.1.1 is not a valid adress". Also when I restart device it automaticaly sets its IP to 192.168.2.1. I have static IP which is translated to IP in subnet 1 so I need this working. The router is in "Wireless router mode (Default)"
i have been trying to forward port 25565 for a server on a game called minecraft. I have a bt homehub 2 and i have followed everything on portforward.com and on several videos and still no luck. I have B.T net protect plus so I don't know if the firewall is blocking the port
In asus router model rt-n10, there is a client list when you bring up 192.168.1.1 showing names of devices also mac addresses and ip addresses. How do I add names to the list so I know which devices are using what ip etc. I have tried the advanced settings in the router to see if I can do it this way , but no luck.
I try to login to my router http://192.168.1.1/ I try and put in the user name and password that I think it is. Is it the user name and password you set up or one that's already there and if so where can I find it??
I have 3 3560 switches which are configured with trunks between them. They run vlan 10, 11 & 12. I have a 'core' switch (switch 1) of these 3 to which an MPLS router is connected on vlan12. I in addition have another switch hanging off the 'core' switch via a routed link (switch 4). I have EIGRP configured as a stub and as such the IP address on the routed link at the core switch end is of a /24 from v lan 1 on the other switch. This makes the route directly connected and therefore distributed via EIGRP stubs. Switch 1 is then exchanging routes with the MPLS router (via EIGRP).
The problem I have is that from any sub net on any switch (switch 1, 2 or 3) I can ping 192.168.13.1 (switch 4). When I try and ping switch 4 from over the MPLS I am unable to. If I trace to the switch I see it reaches the outside of the MPLS router, but is then unresponsive. The same applies if I try to ping switch 1 on 192.168.13.2. Any of the other IP addresses of switch 1 respond.
The MPLS network is a managed solution to which I have no access. I'm told that the MPLS provider is able to ping switch 1 & switch 4 on the 192.168.13.x addresses from a remote router (192.168.32.2). I have tried from a switch on the same L2 sub net (192.168.32.1) and I don't get a response.
From switch 4 I am able to ping the switch on 1 of it's interfaces (192.168.19.1), but not the interface I mentioned above 192.168.32.1. There are no access lists in place on the switches and no firewalls between the sites.
MY ISP installed one router in my lab.for internet connectivity they mail me steps :connect your Laptop directly to gi0/3 port to check internet connectivity with public ip 1.1.1.x and Gateway 184.108.40.206 with subnet mask 255.255.255.240 after connection I surprised because I am able to access only google sites like gmail,google search etc. but I am able to ping/traceroute all sites.from browser I am able to access only google sites only.In Router no firewall no such access list.
I want to separate my house in three zones plus guest W LAN. One for my mother in law living upstairs, One Gega-net for my family and one for my own little company office. Additionally I want W LAN on three of the V LAN's in addition to one guest W LAN.
And I want remote access to my music on the family LAN and my documents on the office LAN.
Can I accomplish this with one (W LAN)router or do I need more equipment?
I am trying to setup internet access and intranet access using two cards per PC. I don't have sever software and I want to be able to share files between several machines. I have two routers. One that connects to cable modem and one that connects to intranet side. I have assigned different static ip addresses to both cards.
I am able to access the internet. I am running Windows 7 on my laptop and have a wired connection between it and my intergrated router. The internet works fine, but it seems to think that I am not connected to the network. I'm not certain it realized that I even had a network, since when I try to activate media sharing it just gets stuck at "Identifying Network". The whole purpose of this is to be able to play music from my computer on my Xbox 360, alternative solutions for this goal would be good too.
how to create a password to access one pc to another pc .like i have 3 pc it is connecting throw switch .ip addresss is 192.168.1.1,192.168.1.2, 192.168.1.3 i want access from 192.168.1.1 to \192.168.1.2 like this here i want to create login password and how to remove password
I am trying to connect to my office PCs via VPN and/or RDP. The office uses Qwest DSL and has a dynamic IP address. I use DynDNS.org to keep the DNS updated with the WAN address of the router. However, any attempt to access the network fails. I have tried remote management access (I enabled it on the router) but that fails. I forwarded RDP ports on the router to one of the PCs but can't connect to it. I also set up a VPN server but cannot connect to it either. Something tells me that all requests to myoffice.homeip.net are not getting to my modem/router. I have even tried the IP associated with the name (Yes, I did check that it is correct!) but nothing works there either.
I have High Speed Charter Internet going to a modem in form of coaxial cable with one Ethernet port available and one coaxial connection for TV and a phone jack. I have that Ethernet port connected to a:Motorola Wireless Modem[CODE]
I've got a Lanpro LP-5420G. Long ago, I was able to set up a password with WPA2. Then I couldn't connect to the internet. I managed to make it work placing the rj45 network cable (that it's originally connected from the modem to the WAN port on the router) to the (number) 1 port. But now, it doesn't let me have access to 192.168.1.1 that it's the original ip for the router. I tried with 192.168.1.1, 192.168.2.1, 192.168.1.100 and others and nothing works.Also, i've got connected another rj34 cable to a normal pc (that was originally connected on port 1) on port 2 now. I don't have internet when I just plug modem cable to the WAN port, and neither I can access to 192.168.1.1 just connecting the normal pc, nor a laptop, nor my IP starts with 192.168...
I have a qsee dvr that is hooked up to a switch that is connected to a wirless router/modemI have forwarded the correct ports that I need to according to qsee, ports 80, 9000 and 100I can access the dvr from any computer on the network via its local ip address, but when I try to access it via a computer off of the network via the real world ip address of the network, I cannot access it. I can ping the real world ip address of the network and it is successful.