Region : Argentina
Model : TL-MR3020
Hardware Version : V1
Firmware Version :
ISP :
I wan't to buy this 3g router, buy i don't sure if my MD300 Sony Ericsson is compatible.There are some site with information? In the compatibility list it's not listed.
Region : Australia
Model : TL-MR3420
Hardware Version : V2
ISP : Optus, Telstra
Whilst the MR3420 V2 is sold as a 4G usb router, it appears that it does not support many usb 4G devices.In Australia we currently have the Seirra 320u, ZTE MF821 (100Mbps Cat 3) and Huawei E3276 (150Mbps Cat 4)whilst the V2 supports the first two (not the E3276), it has one major failure!It does not work at full 4G speeds.
The V2 does not appear to allow download speeds in excess of 25Mbps or uploads much greater than 2Mbps. This occurs on fast 3G and 4G networks.The throttled speed is apparently due to slow modem protocols deployed in the router. High protocol overheads mean it cannot 'shuffle data' very fast.We have developed working solutions using the Openwork platform that overcome these issues and provides speeds in excess of 70mbps.
Region : Others
Model : TL-MR3020
Hardware Version : Not Clear
Firmware Version : 3.14.2
ISP :
Can I set to 3g And then go back to 4g when I want to?
Region : Others
Model : TL-MR3020
Hardware Version : V1
Firmware Version : TL-MR3020_V1_120817
ISP : Vodafone
Can TP-Link add more Countries like Malta we have Vodafone,GO, Melita ISPs
Region : Germany
Model : TL-MR3020
Hardware Version : V1
Firmware Version : 3.14.2 Build 120817 Rel.55520n
ISP : T-Mobile
is it at all possible to lock a 2G/3G-Stick to 2G or 3G with the TL-MR3020 (e.g. if the desired network (2G or 3G) strength is low)? If not, this would be a useful feature for upcoming firmware versions
Region : India
Model : TL-MR3020
Hardware Version : V1
Firmware Version : 3.14.2 Build 120817 Rel.55520n
I Recently Purchased MR3020 it Connected well the First day, and everything was fine but second day it dint got connected with internet - when i plugged into the system i noticed that it is not identifying the 3g Stick (data Card) i also upgraded the firmware as directed by the Global Customer Care - but there was no Improvement there is no Reponse on Email or Phone from the Tp-Link Support.
Region : Argentina
Model : TL-MR3220
Hardware Version : V2
Firmware Version :
ISP :
I set my TL-MR3020 to AP to act as a repeater to boost my wifi signal in the living.My TL-MR3020 is able to ping the main router but there is no internet access (no Internet light) on the TL-MR3020 . The main router ip is 192.168.1.1 and TL-MR3020 IS 192.168.254.0I followed exactly the instructions on how to configure the TL-MR3020 from TP-Link website and everything seems ok except no internet
Region : UnitedKingdom
Model : TL-MR3020
Hardware Version : V1
Firmware Version : mr3020nv1_en_3_14_4_up(121129).bin
ISP : Three mobile data sim
Possible to use a mobile via the usb connection on a TL-MR3020. The reason being is that my mobile data plan allows unlimited tethering through my phone...yet when I place the sim from the phone in the usb modem I get blocked by the provider stating that the sim can only be used in a mobile phone. Mobile data plans in the UK are very expensive and you get very little for your money.
Region : Philippines
Model : TL-MR3020
Hardware Version : V1
Firmware Version :
ISP : Smart Communications Inc.
TP Link,
Your 3g router model TL MR3020 is not compatible with USB modem WM66E. Is there a workaround for this? Any existing bin files?
Region : Brazil
Model : TL-MR3020
Hardware Version : V1
Firmware Version : V1.00 120817
ISP : CLARO (Brazil)
I have three 3G Routers TP-Link TL-MR3020 120 817 V1.00, a modem 3G Huawei E303C and another 3G modem ZTE MF-190 with ship operator CLARO (BRAZIL). I can not get 3G Router 3G modems work with these, although it is loaded with the latest firmware.
Region : Argentina
Model : TL-MR3220
Hardware Version : V2
Firmware Version :
ISP :
Region : UnitedStates
Model : TL-MR3220
Hardware Version : Not Clear
Firmware Version :
ISP : None
I'm a court reporter trying to set up a connection between my laptop and my court reporting machine, which has built in wifi capabilities. My court house has public wifi but there is always some interference which causes transmission between my laptop and machine to freeze. I was told I could create my "own wifi" between my machine and laptop if i bought a router. is this possible with this hardware?I don't need the internet or want an internet connection. I have the internal modem in my laptop. I just want to provide a connection between my laptop and writing machine wirelessly. That is, data being sent back and forth between the two. (Like your headset and smartphone connected with Buetooth). I can use the Bluetooth method to connect the two, but I opted for wireless connection because Bluetooth still can have some interference when attorneys come in the courthouse building with a Blackberry smartphone. I heard this router will provide a secured, private wifi connection between my laptop and machine.It doesn't say anywhere in the instructions that how to do this or I just don't know which method to use this router for what I want to do. Is it WISP, AP or BRIDGE, etc...?
Region : U.SA
Model : TL-MR3220
Hardware Version : V2
I'm a court reporter trying to set up a connection between my laptop and my court reporting machine, which has built in wifi capabilities. My court house has public wifi but there is always some interference which causes transmission between my laptop and machine to freeze. I was told I could create my "own wifi" between my machine and laptop if i bought a router. is this possible with this hardware?
Region : UnitedStates
Model : TL-MR3020
Hardware Version : V1
Firmware Version : latest
ISP :
I have problem to get pptp working. I setup pptp VPN server on my home router and configured pptp dialup on my laptop. If my laptop connect to internet directly, I am able to connect to home router via PPTP VPN. However, if I connect TL-MR3020 to internet(wired) and then connect my laptop to TL-MR3020 wirelessly, I can browse internet without problem. The problem is I cannot connect to home router via PPTP VPN any more. I believe the problem is on TL-MR3020.
Region : UnitedStates
Model : TL-MR3020
Hardware Version : V1
Firmware Version :
ISP : Virgin Mobile with MC760 antenna
In remote areas, I use Virgin-Mobile's MC760 Broadband2Go antenna to provide Broadband to my netbook. This ISP service requires that you "sign in" with username and password to initialize the BB transmission. I would like to use my TL-MR3020 to host the Virgin-Mobile's Broadband2Go MC760 antenna to provide a wireless hotspot, instead of the hardwired direct-computer connection I have. I've gone thru the MR3020 quick setup with the MC760 but been unable to get it to connect. The 3020 is putting out the wireless signal...it's just not connected to my Virgin-Mobiles BB service...thus no www internet tie. how to use the MR3020 with Virgin-Mobile's MC760 (3G/4G) Broadband2Go antenna?
Region : India
Model : TL-MR3020
Hardware Version : V1
Firmware Version : 3.14.2 Build 120817 Rel.55520n
ISP : BSNL India
I bought this device yesterday, I am using this device with BSNL's EVDO (cdma network).It detects my modem fine, and it connects fine, and I can browse.Exactly at 50th min(few seconds difference), my net gets disconnected.I have tried all modes, connect manually, automatically, on demand -- nothing solves the concern.Changed idle timeout to 0.The device when connected directly works fine for more than 12 hours.Updated firmware to the latest 3.14.2 Build 120817 Rel.55520n.Tried Resetting the Router to factory defaults and configured again.Tried all troubleshooting steps from FAQ as in change it to WEP security, connect manually, idle timeout setting.Most importantly, tried creating a BIN file using USB sniffer and used it, even then its the same issue.
Region : India
Model : TL-MR3020
Hardware Version : V1
Firmware Version : 3.14.2 Build 120817 Rel.55520n
ISP : HNS/Instanet (Cable Internet)
I am using the Router in 3G/4G mode, with WAN only (PPPOE) enabled. I have set a personal SSID in the Wireless > Wireless Settings > Wireless Network Name field.
I do not see the particular SSID on my computer, instead on every reboot / restart of the device a random SSID is generated. see attached screenshot. I can connect and everything works well, but I have to enter the WPA key after each reboot.
Region : Germany
Model : TL-MR3020
Hardware Version : V1
when visiting Switzerland and Italy with my German SIM card I noticed that roaming is not working very good with the TL-MR3020. The reason is that the internet provider needs to be set in the config, in my case to o2 Germany.When I travel with this SIM card to another country, I roam into other networks.As I cannot what provider is currently active (as o2 has contracts with almost every provider outside Germany) and even if I could see it I have to adjust the settings in the config if anything changes, the satisfaction effect on this trip was not very good.
Also I noticed that sometimes (only sometimes) the setting resetted itself to o2 Germany when unplugging the device, this added some extra negative satisfaction to everything.In my understanding the router should have an auto detection for the currently active network and auto setup for the dialin parameters and everything else. Like every smartphone on the planet. Maybe you can also add a setting where you can enable or disable data roaming to save people money if they do not have a international data option booked.
Region : UnitedStates
Model : TL-MR3020
I'm using a 3020 to bridge 3/4G to the ethernet port on my computer. Things work fine until I also join wireless hosts (like an iPhone or iPad). The routing of traffic to both the ethernet and wireless hosts seems to cause the 3/4G router to lose the signal and disconnect all hosts. I'm using a Verizon LG USB wifi device that is on the compatible list of 3/4G devices. I'm using the latest version of the firmware on the 3020 (I believe the date is Sep 2012).
Region : Hongkong
Model : TL-MR3020
Hardware Version : Not Clear
Firmware Version :
ISP :
I have installed a mini router type MR3020.I have set it up to WISP mode in order to get wifi signal from my main router and be able to deliver wifi to other devices The main router is working fine and I can access internet with no problem.However, the mini router, which detects the main router, is unable to supply internet connectivity. The ip addresses in teh WAN part under network is zero. Though I tried many times to renew the ip address I was not able to get a valid IP address.
Region : Turkey
Model : TL-MR3020
Hardware Version : Not Clear
Firmware Version : (120817)
ISP : turkcell
I have recently purchased the portable TP link 3020 which is a great solution for me in order to get wifi for multiple users till I get through the long process of getting ADSL in Turkey.The thing is that the 3G bundle Turkcell provided me with is not identified by the modem, so I looked it up on the internet and I found out that I needed to add the bin of the bundle, I searched within the list published on TPLINK website but without any luck.... finally I found the bin I was looking for in another country list... mine is Huawei E353 and the one I found is Huawei E353s2. Anyway I added the bin and still not luck identifying the bundle, I finally resorted to upgrade the firmware which I hate because I always worry of the bad consequence of failure, and unfortunately I was right! Once I upgraded the firmware, I couldn't get connected to the router, it keeps asking me for the key, but without any success! I tried hardware reset by holding the WPS button for 5 seconds as suggested in the manual, but any further success!
set up my router. Trying to set up my 3G modem with TP-Link MR3020.
Tried troubleshooting to find out where it went wrong and just couldn't figure out. Just tried disabling the wireless security and *poof* I'm able to connect to the Internet. Right after setting up the Network Key, I can't connect to the Intertnet via my router.
Here are the datas.
Windows IP Configuration
Host Name . . . . . . . . . . . . : TOSHIBAM840
Primary Dns Suffix . . . . . . . :
[Code].....
Though ASA5585-X S-20 and UCS C200 are not in LMS 4.0 supported device table, I'm wondering if there is any way to monitor these devices using LMS? Our data centre has a quite number of UCS C200 servers and two ASA5585-X S-20.
View 7 Replies View RelatedI am having some issues adding updated definitions for Cisco C3750X-48PS switches.
We have ciscoworks LMS 3.2 and I need to update the definition/device support for these switches. We are conducting a network refresh and are having some issues with ciscoworks polling these devices correctly.
I have looked through the various user guides and searched on google with not much luck as to how to actually do this, the links I have found breifly go into it, but not indepth, and the cisco links I have found, of course have redirects to new pages which bear to resemblance to what is in the original document. Is there a clear guide out there on how to update the switch definiton in ciscoworks? So I can i can try and do this correctly?
I am unable to successfully authenticate my SG200 to either a Cisco ACS or Windows2008 RADUIS server. (C3750x on the same network authenticates fine).
Q1. Is this feature (management login authentication to a RADIUS server) supported on the SG200?
Q2. Is so is there any configuration guidance available for both the SG200 and CSACS / WindowsServer2008 NPS?
I hav not got as far as 802.1x uthentication yet, but config example of this would laso be useful.
I have decided to buy a new wireless N enabled wireless router after my house was cleaned out by some robbers. After a long investigation I decided on the D-link DIR 655 as it suited my basic needs the best and since I haven't decided on a broadband supplier yet this should sort any and all possibilities no matter what I choose...
After an equal amount of investigation I decided on a HSPA+ USB dongle only to find that the router does not support the network I have purchased it on. It thenalso seems that it doesn't support the E1820 Huawei dongle either... so fine... I go and buy a Huawei D105 tht should technically be able to connect via the WAN port and would act as an internet gateway. Brilliant.
Now I have tried everything.... static IP on the D105 with a static IP setup on the 655. Connects fine... according to the web interface but NO INTERNET. When I connect my laptop directly to the 105 via CAT5 it works beautifully. DHCP on the D105 with the same on the 655. Connecting... Establishing Link (Please Wait...) FOREVER without ever getting an IP on the 655 (according to the web interface again) ... must be the D105 thats faulty so again plug in the laptop and within milliseconds the IP is assigned and Internet is blazing along again.... The D105 is not Wireless N so I cannot use it as my primary AP and only allows 5 simultaneous wireless connections (that is reserved for my cellphones). Why should I anyway?? the DIR655 should work fine....
Even after having taken it to D-link support at huge cost and effort I still don't have a working rig.... Seems the consultant plugged the D105 straight into the LAN on the 655 and then set his laptop to the same static range to get it to work... SURPRISE - I know that works since plugging the laptop straight into the 105 does the same thing.... But this is not what I want... I want my 655 to be the primary DHCP server for my network and control the allowed workstations that are allowed access to the internet with a working gateway. Bridging is apparently also not an option as that option has been removed so I cannot even bridge my main subnet onto the D105's internet sbnet... What am I to do....
If the 655 3G setup supported more than 2 dongles I might hve been able to use that and not spend anouther R600 on the D105, if the WAN port actually worked in either static or DHCP modes with the D105 that also would have solved the problem and lastly if all else fails and there was still bridging I could hack my own setup together to do what I want. Seems like I was wrong in selecting the D-link product.
Then to make matters worse I find another product with double the features online for half the price that integrates the 3G capability into the route and support more than 2 different models. including all the new Huawei dongles....
Region : CzechRepublic
Model : TL-MR3220
Hardware Version : Not Clear
Firmware Version :
ISP : Ufon
I have a modem ANY DATA ADU-520L and I would like to know whether you are considering supporting this modem in your router?
I have a cabled network printer, Xerox Phaser 6125n, that have always worked properly from my 3 desktop computers and my laptop.A few days ago, my old dlink router went dead, and I replaced it with the TP-Link WDR4300 router. Everything worked as usual afterwards, until I found out I could no longer print on my printer. I can access the printers web interface through the ip adress, change settings and such through the browser, but the printer has offline status in windows and print jobs never leaves the print queue in windows. I tried deleting the printer in windows (tried both windows 7 and 8) to reinstall it.
View 7 Replies View RelatedWhat is the reason to call a router as data link layer device
View 1 Replies View RelatedI have some 2960 switches with Lan Lite ios in my infrastructure.And I try to configure them to support "trust device cisco-phone" and "switchport priority extend cos 0" on ports with cisco phones.But LAN Lite image does not support "mls qos trust device cisco-phone".can I use any workaround to trust cos of cisco phone and to remark PC traffic with cos 0?
View 1 Replies View RelatedRegion : India
Model : TL-MR3220
Hardware Version : V2
Firmware Version :
ISP : Airtel-4G
using ZTE MF 880T LTE modem and TL-MR3220. I am not sure whether TL-MR3220 supports ZTE MF 880T.
Have a potential customer that is looking at the IE2000 series switch and at the Rockwell Allen Bradley switch
Question is does it support Device Level Ring (DLR) capability. I do not see this specifically mentioned in the Data Sheets but it talks about a
Resilient Ethernet Protocol (REP) and I am wondering if this is the same thing?
I have a setup where there are two networks. A 172.16.0.0/16 and a 10.1.0.0/16 that are separated by the dlink router. I am able to ping from the 172 network to the 10 network using a laptop that is directly connected to the router and that laptop can also browse the web fine. However, I cannot ping to that router or access that subnet at all from the 10 network (if I try to access its LAN (the 172 network)). The 172 network is on its LAN and the 10 network is its WAN. I can access its WAN fine. Also, there the router is not recognizing the laptop as a "directly connected deivce" but its not preventing the laptop from using the router. I have tried to make the router as least secure as possible but still nothing.
I thought about making Static Route to point towards the router's LAN but the only option it gives me is the WAN for the exit interface.
Region : Finland
Model : TL-MR3220
Hardware Version : Not Clear
Firmware Version : 3.14.2 Build 120822 rel.577775n
ISP : saunalahti
dosen't support my huawei E392 4G modem. if possible would you make bin for this. there is not other modems that you can get for 4G connections from the service provider so it would be nice if there was more compatibility than some old ancient modems. starts to feel like this is been sold as 4G router and dosen't actually support that at all.