Region : Germany
Model : TD-W8961NB
Hardware Version : V1
Firmware Version : 1.0.0 Build 110707 Rel.32779
ISP : DTAG
would it be possible to add other DDNS providers to the router menu?E.g. I use dnsomatic.com as DDNS service (pretty much the same syntax/protocol as DynDNS, but free and more flexible).
Region : Germany
Model : TD-W8961NB
Hardware Version : V1
Firmware Version : 1.0.0 Build 110707 Rel.32779
ISP : Telekom Germany
I've just ordered the TD-W8961NB to replace my set of Modem & Router by one device.
Actual I have TL-WR940N, where I managed the Wake on Lan over internet by a port forward on port 9 to the local IP and setting up an IP&MAC Binding for this machine in the ARP table. By reading the user guide of TD-W8961NB, I'm missing the ARP Settings. Is there any chance to setup the WOL over Internet on this ADSL Router?
Region : Greece
Model : TD-W8961ND
Hardware Version : V1
I have a TD-W8961ND that I got for my Dads internet connection to replace the awful Zyxel Modem/router. Problem is that the TD-W8961ND is Annex A (euroDOCSIS)We actually needed a TD-W8961NB - Annex B (DOCSIS)I already know that it is possible to convert other routers from A to B and vice versa...Just wondering if there is any way of either cross flashing or if there is a conversion firmware for this router.
Region : CzechRepublic
Model : TD-W8961NB
Hardware Version : V3
Firmware Version : Firmware Version : 2.0.0 Build 120823 Rel.26389
ISP : 88.103.200.11
I had a problem with this ADSL router - the VOIP outgoing calls did not work until I disabled SIP in telnet: ip nat service sip sw off.But the SIP is going to be enabled every time the router restart (or reset to default).
Region : Greece
Model : TD-W8961NB
Hardware Version : V2
Firmware Version : 2.0.0 120823
ISP : otenet
The problem is that the voip is not working. I have 2 offices with adsl connection. A is the central office and B is the branch office. The installation is old with deferent ADSL modem-router(Zyxel). The zyxel at the A office was damaged so i had to change it with Tp-link. The potology with ip and cables is the same. I tested the port forward for voip (port 1720) with telnet from outside of the office and responds correct. When i try to call from the A office to B office it seems that i can not connect. When i call from B office to A office the phone is ringing and i can not hear office B but office B hear office A. When i use the old modem router at the office A everything is working fine but the modem-router works just for a while so i have to change it. I closed the firewall but the problem is still the same. I talked with the local distributor and they tolded me that i have to correct the configuration. At the interface setup is chosen the dynamic at the section get ip and not static as i should do. The is a problem there. The configuration asks me the subnet mask and gateway. I do not know the subnet mask and either the local distributor and the local internet provider cannot assist. The internet provider told me to use at the subnet mask 255.255.255.240 and at the gateway the ip of the router. I did that but when i did i lost the internet connection. I have to mention that i make some other port forwards to my SBS2003 server and like remote desktop, vpn connections and https that works fine. The only prolbem is with the vpn port forwarding.
Region : Others
Model : TD-W8970
Hardware Version : V1
Firmware Version :
ISP :
I just set up DDNS for my home, and also set forwarding port 5000 for my NAS with an specific IP address 192.168.1.xx. Then, I use my office Internet to call DDNS xxx.dyndns.org:5000 to connect the NAS in my home, It is working OK (from outside to home) However, if I call xxx.dyndns.org:5000 by my home Internet, it is not working (from inside home to home). But if I directly call NAS' IP address 192.168.1.xx:5000, it is OK to reach it. So I think, DDNS used behind TD-8970 (inside home) is not working. TD-9870 is not forwarding port.
I don't know what do I miss in setup this WD-8970.
My previous Zyxel wireless router modem can allow me to us DDNS behind it with out any extra setting. Is it possible that there is still some bug in Firmware of this TD-8970?
Region : UnitedStates
Model : TD-W8960N
Hardware Version : V3
Firmware Version : 1.4.0 Build 111130 Rel.54317n
ISP : century link
How do I test my routers ddns? My computer went down. So, my adsl ip address changed. I caused the modem/router to reboot. But the new ip wasn't sent to the Host (dyndns.org). I had to update my ip manually on [URL].
Is there any free DDNS providers that can be used with a EA6500 ?
View 3 Replies View RelatedI have some network experience but not a lot so here is my problem.I have a zyxel q1000z from qwest that i want to bridge to my dir 655.I go through the settings to put their router/modem to bridge mode. This units default ip is the same as tslinkink, 192.168.0.1 so i change the d-link to 192.168.0.2. I then go into the D-link and enter my isp's pppoe settings and password. I reboot when i am done but can't connect to the internet.It shows connected but that's it. I want to use the d-link as the only router as the zyxel has very few settings and has slowed down my netflix.
View 2 Replies View RelatedHooked up this router the other day to replace my old Linksys G - which has been bulletproof for 8 years. I am now wondering if I made a mistake with this unit.
I set up DDNS - after much trial and error with dyndns it now works fine.I tried to set up NTP time function - does not work. Then I set time manually. Of course on reboot it looses the time since there is no internal time function. So I need NTP.In the course of troubleshooting I turned off DDNS and behold the NTP time function now works. I turn DDNS back on and NTP does not work.
I see no logical connection between these two functions, yet the seem to interact (or not) somehow.When the NTP is not working, on reboot the time displayed in the router is the last time that I MANUALLY set the time, even though that is grayed out since I have (supposedly) activated NTP.
If I do NOTHING to NTP and uncheck DDNS, after reboot the time is correct.I tried many different NTP servers all with the same result.Looking back on-line, I see the NTP function has been a continual problem with some folks (maybe those using DDNS?) in earlier firmware. Come on DLINK don't you think it's time to get this fixed?
Region : Portugal
Model : TD-W8970
Hardware Version : V1
Firmware Version :
ISP :
Two week ago I bought the TD-W8970 ADSL router model. Im using a canon pixma IP4700 printer connected to the router USB print server port and everything is working without any issues if I just look to the router functionalities.
However since that Ive installed TP-LINK USB Printer Controller, my both computers (desktop with windows 7 and laptop with windows 8) are getting very often some BSOD.
I was editing all files automatically generated by windows on this cases and if seems that the cause of this issue is the file TplinkUDSMBus.sys (installed by USB Printer Controller).
To check the impact of this, Ive uninstalled the TP-LINK USB Printer Controller software from my laptop and I dont have any BSOD since 5 days ago. In the desktop Im still have the same issue.
The router print server is a nice functionality and I really want to use it.
Region : UnitedKingdom
Model : TD-W8968
Hardware Version : V1
Firmware Version : latest
ISP : french orange
I am trying to set up port forwarding on this router but it seems I need to use virtual servers but in all the guides there is a menu for this under the advance settings nat menu.I do not have that option, I have downloaded the latest firmware but still nothing.
Everythings works great except thee fact that my DIR-615 router
(Hardware Version: H1 Firmware Version: 8.00) logs the following error :
[SYSTEM]: DDNS error connecting to members.dyndns.org:80
I just had to get rid of a bad DIR-825 that I replaced a trusty old DIR-655 with and now I'm back. Anyhow, I can't seem to make the DDNS setting stick in the router. All of the information is correct, but it doesn't seem to want to login. When I click the enable check box, it tries connecting and then greys out and doesn't connect.
View 3 Replies View RelatedRegion : Australia
Model : TD-W8970
Hardware Version : V1
Firmware Version :
ISP :
Im having issues setting up port forwarding with my Synology NAS.
My house is all connected via network cable, going to a main 24-port switch, which is connected to a Modem/Router (TP-LINK in this case). I can access the NAS from anywhere on my home network, send and receive is fine. I previously used a Billion modem/router in the same config and it all worked fine.
The problem is that when going through the Synology setup, it fails to see the tp-link. So therefore I cannot run its port forwarding program to setup all my ports. Which in turn the NAS can't access the internet. I have started going through the port-forward setting on the router interface, and manually entered the ports - i realized that I'm limited to the number of ports i'm allowed to open! I have also run a port testing program, some are successfully opened the others are not.
Is there some button i need to check or switch on the modem?
Region : Italy
Model : TD-W8970
Hardware Version : V1
Firmware Version : TD-W8970_V1_130201
I just bought online a brand new TD-W8970 modem/router but I'm in trouble with getting ADSL working.I set up a PPPoE connection with the settings from my ISP but the ADSL Led on the device is solid OFF and in the Admin section it says DSL Status: Not Connected.
[code]...
Region : UnitedKingdom
Model : TD-W8970
Hardware Version : V1
Firmware Version :
ISP : Virgin
I've just replaced my aging ZyXel Wireless Router with a TD-W8970 which connects to the internet with no problems whatsoever. However, I have an ethernet connected Western Digital MyBookLive NAS which is happily allocated an IP addess but does not show up on my network on my PC (Windows Vista - fully patched). A usb connected pen drive and exactly the same. Am I missing something blindingly obvious? On the ZyXel the NAS worked with no problems whatsoever.
The problem with the NAS was my internet security Bitdefender. For some reason, on installing the TP-W8970, it switched my firewall status to public from home/office. Corrected that and the NAS can now be seen over the network. This does not fix the USB attached pen drive not being seen problem though.
Region : India
Model : TD-W8968
Hardware Version : V1
Firmware Version :
ISP :
According to inSSIDer the router seems to be using two wifi channels (10+6) and inSSIDer is recommending to move to a standard channel (1,6,11).
Region : UnitedKingdom
Model : TD-W8960N
Hardware Version : V3
Firmware Version : 1.4.0 Build 111130 Rel.55990n
ISP : BT Broadband
Just got myself a new Modem/Router (TD-W8960N), and it wasn't until I had it all up and running that I realised it didn't have USB port on the back.Anyways, I was wondering how I could go about fixing this? I stumbled upon this (TP-Link TD-8817) on Amazon and wasn't sure if I could attach this to it in bridged mode or something. This has the USB socket I need. If this was all I needed, how do they connect together? I have a BT connection btw.Also, I have a Justop Android 4.0 TV Box (media player). Would this be able to see the HDD for streaming movies.
Region : Others
Model : TD-W8901G
Hardware Version : V6
Firmware Version :
ISP :
problem with filtering
Region : Syria
Model : TD-W8901G
ver 6.0
54Mbps wireless G ADSL2+:
I used the url filter utility inside the router program. I put some url for example www.google.com, I wanted to try the filtering cababilty, Later I deleted all these adresses , but unfortunatley it keeps telling me the following message: "The system returned: (110) Connection timed out The remote host or network may be down. Your cache administrator is webmaster@proxy1."
I use a wired network connection to my neighbours Vodafone Modem (We share his monthly cost). I also have a TP-LINK 54M Wireless ADSL2+ Router from a previous broadband contract with a landline phone company. Is it possible to reset and configure the TP-LINK Router to act as a relay unit, connected to the network cable, so I can then use my laptop elsewhere in the house?
View 3 Replies View RelatedRegion : Spain
Model : TD-W8961ND
Hardware Version : V3
Firmware Version : 3.0.0 Build 120524 Rel.05221
ISP :
linksys1.jpg
I have wifi at home this link installed.
192.168.1.1 is a TD-W8961ND
192.168.1.4 is a linksys wrtt54gl
And I have two problems.
1) I can not see any desktops in my local net, and with old router I could see all, for example (diskstation, dm800, etc...) In my macbook air I can not see my NAS Synology and with old router I do.
2) All PCs that are conected to 192.168.1.4 have not IP. and DHCP in TD-W8961ND is activated.
Region : India
Model : TD-W8151N
Hardware Version : V3
Firmware Version : 120530
ISP : BSNL
Net is working smoothly from LAN, but no success on wifi. Over wi-fi, I can connect to router but cannot access net.
Region : Argentina
Model : TD-W8968
Hardware Version : V1
Region : UnitedKingdom
Firmware Version : 101029
ISP : TalkTalk
I have version 1.1 and d/l'd firmware 111125. The upgrade ran successfully to 100% and then I got the login screen again. However after checking, then restarting to factory default the version displayed was still the old one
Model : TD-W8960N
Hardware Version : V1
Firmware Version : 1.4.0 Build 111108 Rel.40398n
ISP : TPG
URL Filter not working
Region : Australia
Model : TD-W8960N
Hardware Version : V1
Firmware Version : 1.4.0 Build 111108 Rel.40398n
ISP : TPG
Cannot get the URL filter to work Just upgraded to latest Firmware but that didn't work?
URL List Type: Deny Allow Disable
Address Port Remove
[URL]
Model : TD-W8951ND
Hardware Version : Not Clear
Firmware Version :
ISP : Metronet BPL
I connect to the internet by BPL modem on electricity , for using my modem's wireless feature ı have to close DHCP and use modem in bridge mode, otherwise I can't use wireless, And my problem is connecting to the internet with my LG 42LM640S smart tv using wireless, When I talk with LG techinal service they came and try to connect tv to the internet with using their android phone's hotspot feature, my tv connect with phone's hotspot feature to the internet,So they said that "you have to change tp link modem's encoding system?Now it's encoding mode in WPA enconding system :S But whwen ı shut down encoding wireless tv didn't connect again?
Region : Others
Model : TD-W8961ND
Hardware Version : V2
Firmware Version : 2.0.0 Build 120427 Rel.09135
ISP : True
I just bought the wireless router as stated in the subject and I cant get 2 of our PC�s to connect wirelessly for some reason. 4 other PC's are fineAll machines running windows 7, but when the authentication type on WPA2-PSK the 2 computers ask for a password which we put in but keeps saying its wrong, but infact its right.I can connect them on WPA-PSK, but then all the computers drop out after 30 seconds.
Region : Italy
Model : TD-W8970
Hardware Version : V1
Firmware Version : 0.6.0 1.2 v000c.0 Build 130201 Rel.54921n
ISP : Infostrada
My TD-W8970 freezes randomly, sometimes several times a day, sometimes less, but now the problem it's more frequent and I suppose it could be generated by some internal component that could have a abnormal behavior.Anyway, this happens in different situations, either using all the functionalist, or being only on and in idle state. Last time was few minutes ago, when all the system were shuttled down and only router was on.
Region : NewZealand
Model : TD-W8960N
Hardware Version : V3
Firmware Version : 1.4.0 Build 111130 Rel.56405n
ISP :
According to the manual, when I go to edit my WAN connection, I should be able to enable/disable the SPI firewall. However, on my firmware I get no such option. My SPI firewall is always enabled.
I would like to be able to completely disable it when I'm testing so that I can ensure the firewall is not interfering with my tests.
Region : India
Model : TD-W8951ND
Hardware Version : V4
Firmware Version :
ISP :
The product manual of TD-W8951ND V4 states that it's supports MAC spoofing. But in the product itself, it is nowhere to be found. I tried contacting the customer care via email but they are too lazy to respond. If they disabled this feature then why in the world they mentioned in the manual. I double checked the manual before buying this model. Now I stuck with it.
Region : Others
Model : TD-W8960N
Hardware Version : Not Clear
Firmware Version :
ISP :
Region : Sweden
Model : TD-W8960N
Hardware Version : Not Clear
Firmware Version :
ISP :
opening of some ports 25565 for minecraft so i can host games. i have try so solve this by my self but with zero progress. did enter the advanced setup and then i pressed on the NAT category and then i pressed on the ADD button and enter the following" [URL] and then i used a port checker to look if it worked but did not work?
Region : CzechRepublic
Model : TD-W8901GB
Hardware Version : V3
Firmware Version : 100820
ISP : Vodafone
I have a question. Is possible for my model 8901GB v3.4 set IP adrress reservation ? I didnt find how to do it.
Region : India
Model : TD-W8968
Hardware Version : V1
Firmware Version : 0.6.0 1.1 v0005.0 Build 120926 Rel.27100n
ISP : BSNL
I Bought this w8968 a month back.. It was working alright till a few days back. When i connect and start browsing or downloading, it goes OK.. but after a few hours(sometimes 2, sometimes 1), It stops responding and I couldn`t ping 192.168.1.1 either through WiFi/Ethernet. Status indicators for DSL/WIFI/Internet/LAN all glowing as though nothing wrong with them..? The router is not that much hot when this happens.. When i switch off the router and then on, The Prob gets solved only to reappear again in 1/2/3 hrs..