Using A Hosted Backup Service

Jun 7, 2011

I got two offices about 150KM from each other,i need to backup 10 to 20GB / machine,the data ranges from accounts package to doc files etc.i suggested a vpn, then backup from one side to the other and vice versa as this ensures backups are swapped over and are off site.Would you recommend this, or am i better off using a hosted backup service i pay for / GB?

View 8 Replies


ADVERTISEMENT

TP-Link 300Mbps Wireless :: Limiting Backup Service On TD-W8960N

Feb 15, 2013

Region : United Kingdom
Model : TL-WR940N
Hardware Version : Not Clear
Firmware Version :
ISP : BT

I've been having some issues with my BT Broadband for a while, so decided to switch to a new router, a TP TD-W8960N, however setting up QOS isn't as easy as I had anticipated (I'm fairly new to this!).

My main issue is that we have a fairly limited broadband connection, but I need to backup work using backblaze. This is a pain because as soon as it starts to backup it eats what bandwidth we have. What I want to know is can I just limit the range of ip-addresses which they use for their backup?Is there a simpler auto-QOS approach I could use? The router is currently running the latest firmware that isn't in beta. Also - do these routers auto-update firmware?

View 2 Replies View Related

Cisco WAN :: Dial Backup To ADSL Service Using 877 / External Analogue Modem

Jan 4, 2011

I'm trying to get a solution together for a dial backup to an ADSL service, using an Analogue modem.The kit list is as follows:

Cisco 877
 
Multitech MT5656ZDX External Analogue Modem or USR 5630D External Analogue Modem
 
Rolled patch cable RJ45 to DB25M adapter (pinout from a cisco guide)
 
So far I am unable to get the router/modem to dial out at all. I know the modems work, I have tested them from Windows.
 
I have attached a couple of outputs from "show line" and "show line 1" from the router and also what I think are the relevent lines of config although it will be too much config and probably jumbled by now as I've tried quite a few things to try and get this working.
 
I am more concerned with the config relating to the connection of the analogue modem than the routing element.

View 5 Replies View Related

Sharing :: 8032 - Browser Service Has Failed To Retrieve Backup List Too Many Times On Transport

Dec 14, 2011

This network has a peer network with a mixture of Win 7, Vista and XP computers. The network problem I am having is with an XP computer that was able to access network shares on a Win 7 Pro (64-bit) computer yesterday, but cannot today. I tried repair steps that have worked for me in the past, but didn't today.

1. Rebooted.
2. Turned off Windows Firewall.
3. Re-ran the Network Setup Wizard and select turn on file and print sharing.
4. Changed IP configuration to choose NETBIOS over TCP/IP.
5. Uninstalled AV software.

Error Messages that I have been receiving:

1. When attempting to connect to a share on Win 7 PC: "Microsoft Windows Network: The specified server cannot perform the requested operation. The connection has not been restored."

2. When trying to view the computers in the workgroup: "Workgroup is not accessible. You might not have permission to use this resource. Contact the administrator of this server to find out if you have access permissions. The specified server cannot perform the requested operation.

3. When using the command, "NET VIEW" from the command prompt: "System Error 58 has occurred.

4. Event Log: Browser error 8032. The browser service has failed to retrieve the backup list too many times on transport DeviceNetBT_Tcpip_{06ECF93A-1B89-4FF4-923E-F3302EF95FE1}. The backup browser is stopping.

View 3 Replies View Related

Hosted Exchange - Only One Connection On Network

Sep 7, 2012

We started out by switching them over from a normal POP server email service through Outlook and getting them onto Charter hosted Exchange. However, after getting them all set up, we had intermittent connection problems keep occurring. Here is what I know so far:

-the problem is with their network for sure

-re-imaged computers and reinstalled office

-any connection to exchange.charter-business.net is intermittent from their location only.

-replaced modem, router, switch

-tried different DNS servers, same problem

-used their DNS servers from another location, no problem connecting

Once we replaced their switch, the problem morphed a bit. Now, one of them can be connected at any given time without having problems. However, when the other tries to connect, they can't get through. E.g, if user #1 closes outlook, user #2 can now connect without problems.

View 3 Replies View Related

Linksys Wireless Router :: New EA3500 With Self Hosted Web Server?

Dec 26, 2012

I was using a wrt54g previously, and host my own webserver, including my own DNS server. I used port forwarding to forward the web traffic to that computer. Well my family got me a new EA3500 as my old one would continually stop working.Since changing router when I duplicate the port forwarding setup from old to new, all the web browsing dies. My web server has now been offline for a few days, and I'm frustrated beyond belief now. I know I've seen the previous posts saying to never forward port 53 (DNS), but I'm at a loss why I could with my old router, but it's now the end of the world with this new one. 

View 9 Replies View Related

Cisco Switching/Routing :: 1841 - Connecting To Hosted Websites

Jan 10, 2013

Here's my setup:

 - Cisco 1841 connected to the internet on fa0/1
- LAN connected to fa0/0/1 (switch port, connected to Vlan1)
 
On my LAN I have a web server that houses different websites. Those websites have DNS records that point to my public IP address, located on fa0/1. From the outside I can reach the websites perfectly, but I can't reach them from the inside. So it looks like I can't seem to connect from my local LAN address to the public ip address on the Cisco (who then should NAT it to the correct server)
 
Here is a snippet from my config:
 
--NAT--
 ip nat inside source static tcp 192.168.0.3 80 interface FastEthernet0/1 80
ip nat inside source route-map Internet interface FastEthernet0/1 overload
 
--OUTSIDE INTERFACE--
 interface FastEthernet0/1
description WAN
ip address dhcp
ip access-group WAN-IN in
[ code]...
 
--INSIDE INTERFACE--
 interface Vlan1
description LAN
ip address 192.168.0.254 255.255.255.0
ip access-group LAN-IN in
[Code]....

View 3 Replies View Related

Cisco Firewall :: Ports To Be Opened Up For Hosted Voice Access On ASA 5515X

Sep 23, 2012

I have a customer who is going to host a VOICE services like providing SIP services to its customers. What specific ports required to be opened up for this on ASA  5515X. I would rate it ASAP.

View 3 Replies View Related

Cisco VPN :: RFC1918 / Setup VPN Tunnel To Vendors Hosted Network For AD Authentication

Oct 25, 2011

I am in need to setup a VPN tunnel to a vendors hosted network for AD authentication.To prevent RFC1918 Address overlap we are trying to NAT into a VPN Transit Network.I was given 209.235.17.232/19 and need to NAT these addresses:

209.235.17.233 <> 172.20.0.42
209.235.17.234 <> 172.20.0.43
 
The vendor is using 209.235.17.224/29 and NAT'ing to some 10.122.xx.xx addresses.
 
The Phase 1 requirements are:
Pre-Shared DH-Group2-AES256-SHA1 86400 seconds
The Phase 2 requirements are:
NOPFS-AES256-SHA1 3600 seconds
 
I have many l2l VPN tunnels configured using esp-3des esp-sha-hmac This is what I have configured on my ASA:
 
static (INSIDE,OUTSIDE) 209.235.17.233 172.20.0.42 netmask 255.255.255.255
static (INSIDE,OUTSIDE) 209.235.17.234 172.20.0.43 netmask 255.255.255.255 
access-list VPN-TO-JIVE extended permit ip 209.235.17.232 255.255.255.248 209.235.17.224 255.255.255.248
access-list VPN-TO-JIVE extended permit ip 209.235.17.224 255.255.255.248 209.235.17.232 255.255.255.248

[code].....
 
Currently my side is trying to initiate the tunnel, but we are getting this message:
 
15  IKE Peer: 65.168.255.157
    Type    : user            Role    : initiator
    Rekey   : no              State   : MM_WAIT_MSG2
 
I am configuring the transit network for the tunnel properly or performing the NAT for my 2 devices.I am still trying to determine what device the Vendor has on their end.

View 1 Replies View Related

Cisco Firewall :: 5505 Access Websites Hosted On Local Web Server

May 4, 2013

I have a Cisco ASA 5505 in my home office which has a few PCs behind it with a linux web server running some websites. I can access the websites from outside no problem (i.e. on my iPhone using a 3G connection). However, I struggle to access the websites from within the network. The ASA gives me this error: [code]

View 3 Replies View Related

Cisco WAN :: 1841 - VOIP Phone Not Able To Contact Hosted Server On Internet

Mar 11, 2010

We have 2mbps leased line and have Cisco 1841 which is managed by our ISP. I have hooked up another 1841 (please find basic config below, it will get more complex lateron) Now when I connect my laptop I am able to browse Internet. But when I conect VOIP phone, it is not able to contact it's Hosted Server on Internet.
 
VOIP phone is Polycom SoundPoint 550 and I get URL call disabed message.  If I try netgear Firewall everything seems to work.that the voip provider needs following ports UDP Range 16384 - 32766, TCP 5060 & UDP 5060. But in my config all outbound traffic is allowed. [code]

View 6 Replies View Related

Cisco Firewall :: ASA 5510 / Ip Service Object And Service Group

May 16, 2011

When I create a service object or group and add the object to a new rule it never works.I mean the traffic match not the rule. I see not hits.I placed the rule on top of my access list to check if I do somethink wrong but it is not working. When I place only a service for example tcp/23 it is working.
 
my ip service object
object-group service g-as400 description access client 2 as400 machine service-object tcp-udp destination eq 397 service-object tcp destination eq 137 service-object tcp destination eq 2001 service-object tcp destination eq 3000 service-object tcp destination eq 445 service-object tcp destination range 446 447 service-object tcp destination eq 449 service-object tcp destination eq 5010 service-object tcp destination eq 5544 service-object tcp destination eq 5555 service-object tcp destination range 8470 8476 service-object tcp destination eq 8480 service-object tcp destination eq

[code]...

View 8 Replies View Related

TP-Link Dual-Band Wireless :: Unable To Load Website Hosted Behind WDR4300 At Times?

Jan 15, 2013

Region : Canada
Model : TL-WDR4300
Hardware Version : V1
Firmware Version : 3.13.23 Build 120810 Rel.44064n
ISP : Bell Canada

We have a WDR4300 router that works well about 98% of the time. We have a static IP address from our ISP configured through PPPoE in the router and are hosting our own email and web server at local IP 192.168.1.200 behind the router. Port forwarding is enabled and working beautifully.

At some times throughout the day, any computer behind the router on our local network is unable to browse to our own website by our domain name (e.g. www.xyz.com) nor by the static IP it is attached to. We also get e-mail errors with mail client configured to use the domain name or the static IP it is attached to as the outgoing mail server. When this happens, I am still able to browse any other site on the internet without problem... just not our own. Also, I have verified that while this is happening (internal computers can access the internet but not our own website):

1) I can browse to our website just fine from a computer outside of our network (e.g. a proxy or a computer controlled remotely from my home)

2) a computer from within the office that cannot reach our website using the domain name or the static IP it is attached to can still reach the website by browsing to the local IP address of the web server (192.168.1.200)

3) the problem seems to resolve itself sometime within 45 minutes of noticing it is occurring if we do nothing. We can make the problem resolve itself sooner by restarting the router.

I have the impression that this problem MIGHT start occurring when users are downloading files from our website. Of course, if this is the case, we cannot simply restart the router to fix the problem because then we are cutting off their download.

View 2 Replies View Related

Cisco Application :: ACE 20 Service-policy Out Of Service / Still Able To Connect To VIP

Feb 28, 2012

We have a situation where services are stopped on the real servers. The probes fail and we confirm the services are not running on the server. We cannot access the ports from the ACE directly. We can still however acces the VIP on the TCP port (L4 VIP class-map). So we can still telnet to the VIP on the port from thr Client side of the network.This is on ACE 20 Modules deployed in Routed mode. The version of software is A2(3.3).
 
Tried removing multi-match and loadbalance policies as well as class-map and re-applying then re-appyling the service policy to interface. Same behavior,This is a problem at another level as some services are being monitored by GSS via TCP keep-Alive and this obviuosly causes a problem as the service then never goes off-line.

View 10 Replies View Related

Cisco :: Topology Service In LMS 4.0 / ANIServer Service May Be Down

Mar 25, 2013

I have a fresh installation of LMS 4.0 on windows server 2003, when i click to open topology i get error message : ANIServer service may be down or Host name isn't DNS resolvable
 
i tried pdshow -brief ANIServer ===> service UP

DNS is working using host file in driversetc i restarted the server

restared the crmdmgtd
unistall / install java plugin
pdterm ANIServer
pdexec ANIServer
 
NO change ..

View 6 Replies View Related

Cisco Firewall :: ASA 5505 - Proxy Server Send Register To Hosted Server Private IP Changed

Aug 23, 2011

We have Cisco ASA 5505 with ASDM 5.2 We have one Proxy server in our Local Lab and pointed to Hosted service(Simple Signal)issue is, When our proxy server send register to hosted server, ASA change private IP and post with outside IP and src port as 1063 every time.

Here is debug log on real time monitoring.
 
Aug 24 2011    05:21:19    302015    203.xxx.xxx.226    192.168.1.51     Built outbound UDP connection 3774 for outside:203.xxx.xxx.226/5060 (203.xxx.xxx.226/5060) to inside:192.168.1.51/27014 (99.119.161.107/1142)
Aug 24 2011    05:21:19    607001    203.xxx.xxx.226         Pre- allocate SIP Via UDP secondary channel for inside:192.168.1.51/27014 to outside:203.xxx.xxx.226 from REGISTER message
Aug 24 2011    05:21:19    710005    203.xxx.xxx.226    99.xxx.xxx.107     UDP request discarded from 203.xxx.xxx.226/5060 to outside:99.xxx.xxx.107/1063

Here 99.xxx.xxx.107 is Our ASA Outside IP address 203.xxx.xxx.226 is Hosted server IP address. My ASA config is attached.

View 2 Replies View Related

Protocols / Routing :: Hosted VPN / IP Forwarding / Routing And Bridging?

Apr 5, 2011

I have got a PC at work (Windows XP Pro SP3) that is on two networks with the IPs 10.20.30.167, subnet 255.255.255.0 (internet enabled) and 10.0.0.20, subnet 255.255.255.0 (no internet). On the 10.0.0.X network there is a gateway with the IP 10.0.0.200 allowing access to another network; 192.168.60.X, subnet 255.255.255.0 (no internet). I have added the route on my work PC to access the 192.168.60.X network via this gateway and I can access all PCs on all three networks from this PC.Now, I am using LogMeIn Hamachi so that I can access the networks at work from home. The PC at work is the 'gateway' PC on the Hamachi network. When installing Hamachi it created a new network connection and bridged this connection with my 10.20.30.167 network adapter to allow access to the 10.20.30.X network from an external PC when connected using the Hamachi VPN connection. I have manually configured my Hamachi connection on my PC at home to the IP 10.20.30.169, subnet 255.255.255.0, with the default gateway set to 10.20.30.167. I can ping all computers on the 10.20.30.X network from my PC at home.

I then added a route on my PC at home for 10.0.0.X to go via 10.20.30.167 (the 'gateway' on the Hamachi network). I also enabled IP forwarding on the 'gateway' PC (my PC at work). I can not ping any PC on the 10.0.0.X network from my PC at home apart from 10.0.0.20 (the other NIC in the Hamachi gateway PC) and 10.0.0.30 (another PC on the 10.20.30.X network that is also on the 10.0.0.X network).Now, with IP forwarding enabled on the Hamachi gateway PC I would assume after adding the route on my PC at home for 10.0.0.X traffic to go via 10.20.30.167 that I would be able to ping all PCs on the 10.0.0.X network...I also tried adding a route on my home PC to send all traffic for the 192.168.60.X network via 10.20.30.167 which has a route via 10.0.0.200 to the 192.168.60.X network, but this also did not work.I then tried adding the 10.0.0.20 network adapter into the network bridge that the Hamachi connection made, also keeping both IPs (10.20.30.167 and 10.0.0.20) on this network bridge by adding them into the 'IP Settings' in the 'Advanced TCI/IP Settings'. I also added the 10.0.0.200 gateway for good measure. I still cannot ping any PC on the 10.0.0.X or 192.168.60.X networks from my PC at home.

I have also added the route to the 10.20.30.X network on a PC on the 10.0.0.X network to go via 10.0.0.20 and tried pinging a PC on the 10.20.30.X network but this also has not worked. Also setting the default gateway on a PC on the 10.0.0.X network to 10.0.0.20 does not allow this...Surely bridging the networks 10.20.30.167 and 10.0.0.20 on my work PC would allow another PC on the 10.0.0.X network to access the 10.20.30.X network after adding the route or setting 10.0.0.20 as the default gateway?

View 2 Replies View Related

D-Link DIR-825 :: Way To Add Backup DNS?

May 3, 2011

I periodically have my ISP's DNS go out.  I actually prefer to use the default DNS they provide (and not hard-code it), but still, it occasionally goes-out for an hour from time-to-time.Is there a way on the DIR-825 to add a "backup" DNS (3rd DNS), that is fed to the PeeCees via DHCP, in addition to the 2 my ISP provides?

View 3 Replies View Related

Cisco :: Backup LMS 4.01 Don't Run

Oct 18, 2011

After the upgrade of LMS 3.2 to LMS 4.01 everthing works. After i fixed my last problem (syslog time issue). I´d saw that the automated system backup doesn´t work. I´d tried to backup the system by script. Than i find out that the perl.exe is damaged (0KB). So than i copied the perl.exe from my old Cisco Works Server to the new Server. Than i tried to make a Backup and get the mentiond error ... 
 
D:CiscoWorksCSCOpxin>perl.exe D:CiscoWorksCSCOpxinackup.pl d:Temp
ew
install
************************************************************
Backup to 'd:/Temp/newinstall' started at: [Wed Oct 19 09:39:50 2011]
 [Wed Oct 19 09:39:50 2011]  ERROR(375): No database files are available for the
installed applications; nothing to back up.
[Wed Oct 19 09:39:50 2011]  Backup failed: 2011/10/19 09:40:00

[code]....

View 1 Replies View Related

AAA/Identity/Nac :: ACS 4.2 Backup Through Console / CLI

Jun 6, 2012

Due to some wrong access policy applied in the administration control settings. GUI access is not functioning. So we need to take a backup thru CLI mode using FTP server. I have tried using the backup command in the console & taken the backup using the following steps. But the backup file is less than 1kb. I need the exact Db backup to be taken.
 
Step 1 Log in to the ACS SE. For more information, see Logging In to the Solution Engine from a Serial Console.Step 2 At the system prompt, enter backup and press Enter.Tip You can enter the following parameters after the command or in response to subsequent prompts: [server] [username] [filepath]Step 3 At the Enter FTP Server Hostname or IP Address: prompt, enter the FTP server IP address or hostname, and press Enter.Step 4 At the Enter FTP Server Directory: prompt, enter the FTP server directory pathname, and press Enter.Step 5 At the Enter FTP Server Username: prompt, enter the FTP server username and. press Enter.Step 6 At the Enter FTP Server Password: prompt, enter the FTP server password and, press Enter.Step 7 At the File: prompt, enter the name that you want to give the backup file, and press Enter.Step 8 At the Encrypt Backup file? <Y or N>: prompt, enter Y to encrypt the backup file or N not to encrypt it, and press Enter.Caution This procedure interrupts the use of the ACS SE for AAA services.Step 9 If you entered Y to encrypt the backup file, at the Encryption Password: prompt, enter a password and then press Enter.Result: The console displays:Backing up now . . .

All running services will be stopped and restarted automatically.Are you sure you want to proceed? <Y or N>Step 10 To proceed, enter Y and press Enter.

View 5 Replies View Related

Cisco VPN :: ASA With Backup Peer On L2L VPN?

Jan 10, 2013

Why does Cisco recommend a configuration of originate-only on the ASA with multiple peers configured and the answer-only to the other end? Shouldn't it work as Bi-Directional ?

[URL]
 
The only scenario I see which could break is if both peers try to establish a VPN at the same time to the ASA. Is there any other reason ?

View 0 Replies View Related

Cisco :: Backup Configuration On LMS 4.2

Nov 21, 2012

1)how can i backup the configuration on cisco lms 4.2 and to re-imported later when i re-install the lms 4.2
  
2)how can i change the admin password on cisco lms 4.2

View 3 Replies View Related

Cisco WAN :: 876 To Use It As Backup Line

May 5, 2011

One of my branch offices is connected to an ADSL line as well as a VDSL line.Since I really don't need the ADSL line I came up with the idea to use it as a backup line.So I searched google and found this nice little article URL. I wonder if the router will switch back to the primary ISP if the primary line comes up again?

View 3 Replies View Related

Cisco :: LMS 4.2.2 Cannot Backup An ASA 5525-X

Nov 21, 2012

Any one see the pronl;em where LMS 4.2.2 cannot backup an ASA 5525-X (UKHSL-N01-AFW02)..The Inventory collection is fine, to a point.I have applied all updates LSM etc. [code]

View 7 Replies View Related

Cisco WAN :: ATM Soft Pvc Across T3 And T1 Backup?

May 3, 2006

I am trying to create a VBR soft pvc across a T3 and T1 backup link, but I am confused about what values to use for PCR, SCR and MCR.  If I use high values for the T3, what will happen when this link is down and the soft PVC reroutes across the T1?  I would like to use percents (%) for the values, i.e. voice can use 25% of the link, then it would make more sense when using the backup T1 link.

View 2 Replies View Related

Cisco :: WCS 7.0.230.0 Server Backup

Nov 21, 2012

if i  enable Controller Configuration Backup is that included  in the server backup? and can the controller configs be specifically  extracted from the server backup?

View 8 Replies View Related

Cisco :: Backup And Restore LMS 3.1?

Apr 11, 2012

We have cisco works LMS 3.1  and the server have very problems, we need format the server and reinstall the Cisco Works, when I doin backup and restore of data LMS We lost the licenses? or when we restore the data in the server we have the same licenses? or get the new licenses to cisco?

View 5 Replies View Related

Cisco WAN :: 887 / ATM Router As Backup

May 31, 2012

at the moment I have a 888 router that works fine, I want to configure backup (I already have configure ISDN backup but the performance it's to poor), and I want to use an other router 887 (that I already have) with adsl.
 
My idea is to configure the second router as stand alone gateway, and confiure in the first router a "ip route 0.0.0.0 0.0.0.0 VLAN1 192.168.0.253 100".But I know that this second route is used only in case the interface status of primary route goes down but not in case fault only protocol.
 
configure a better routing or faulting procedure?
 
-----------------------------------
888
VLAN1 192.168.0.254
ATM0.1 1.1.1.1
ip route 0.0.0.0 0.0.0.0 ATM0.1
ip route 0.0.0.0 0.0.0.0 VLAN1 192.168.0.253 100
-----------------------------------
887
VLAN1 192.168.0.253
ATM0.1 2.2.2.2
ip route 0.0.0.0 0.0.0.0 ATM0.1
 -----------------------------------

View 3 Replies View Related

2 WAN Service Combine On 1 LAN

Jun 13, 2011

I want a solution which should be 2 WAN convert in to 1 WAN.

View 1 Replies View Related

RDC Which Service / Software To Use?

Dec 22, 2011

I'm in the process of building a media server, and I mentioned to my wife that eventually we can record her shows in HD and get rid of the costs of having a dvr with our cable bill. I was doing some research and I've come to the conclusion that I may need to increase the budget for my build (which is extremely tight) and will not sit well with the wife. I'm using all older/recycled hardware, specs below:

AMD 4400+
asus a8n 32 sli delux mobo
2gb ddr ram
1tb samsung hdd
antec 600w psu
windows xp

I just read last night that I'll need at least xp pro in order to access my server (host?) remotely from say my parents house on a laptop (client?) Is there a workaround or some other program that I could use for windows environment. I'm considering linux for the server also but I've never used any form of linux before, so I fig'd, until I get the hang of setting up the server and having it working properly, maybe make the switch to linux later. The server will be hooked up to my ps3 which will stream movies/tv shows, and I'd like to be able to access my network to watch shows from a different location when I'm out of town.

View 1 Replies View Related

Make A Backup Of Roles And Their Configurations?

Jun 1, 2011

I have a Domain Controller on windows 2003 advanced server. and I have roles and some configuration such as rights, user accounts, DHCP configuration, DNS server and etc on it.Some times windows needs to be reinstalled but after reinstalling,configuration of roles would be lost. I don't know how can I backup these settings? Is there any solution about this problem.I know a simple way is creating an image of windows installation drive by an application such as Norton Ghost but I'm talking about windows solution.

View 3 Replies View Related

Cisco :: Backup WAN Connections With OSPF?

Feb 11, 2013

implement backup WAN links to complement the metro Ethernet links we currently use so we have some redundancy. These will most likely be a VPN over an Internet service but might be another Ethernet type service, the medium shouldn't really matter I wouldn't think. What I am looking for input on is what is the best way to implement this? Would I just set costs so that the backup is only used when the primary goes down, or should I create new OSPF area for the backup links?

Currently the core switches that are also our routers are 3750G stacks running ip services. We are getting ready to install new firewalls at each location that will become the gateways for the vlans currently on the core switches to give us much more control over segmentation, and because of this I am thinking that it may make sense to then move the OSPF instance from the core to the firewalls. In the drawing I did not show the access layer switches off of the core, and the MOE circuits actually terminate into a 3550-12T switch before the core. I think I will actually eliminate those 3550-12T switches and go straight into the core. This is a current state drawing, so does not include the backup links I am planning.

View 4 Replies View Related

Cisco :: Wireless As Backup Link?

Feb 18, 2011

want to connect three networks with each other via two media one ethernet/fiber optic and other through wireless as backup link.how can i connect these three networks so that if my ethernet/ fiber optic connection fails than computer on networks can still communcate via wireless link (i mean if ethernet/fiber optic fails then wireless link should automatically be established/

View 1 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved