Sharing :: 8032 - Browser Service Has Failed To Retrieve Backup List Too Many Times On Transport
Dec 14, 2011
This network has a peer network with a mixture of Win 7, Vista and XP computers. The network problem I am having is with an XP computer that was able to access network shares on a Win 7 Pro (64-bit) computer yesterday, but cannot today. I tried repair steps that have worked for me in the past, but didn't today.
1. Rebooted.
2. Turned off Windows Firewall.
3. Re-ran the Network Setup Wizard and select turn on file and print sharing.
4. Changed IP configuration to choose NETBIOS over TCP/IP.
5. Uninstalled AV software.
Error Messages that I have been receiving:
1. When attempting to connect to a share on Win 7 PC: "Microsoft Windows Network: The specified server cannot perform the requested operation. The connection has not been restored."
2. When trying to view the computers in the workgroup: "Workgroup is not accessible. You might not have permission to use this resource. Contact the administrator of this server to find out if you have access permissions. The specified server cannot perform the requested operation.
3. When using the command, "NET VIEW" from the command prompt: "System Error 58 has occurred.
4. Event Log: Browser error 8032. The browser service has failed to retrieve the backup list too many times on transport DeviceNetBT_Tcpip_{06ECF93A-1B89-4FF4-923E-F3302EF95FE1}. The backup browser is stopping.
*osapiReaper: Oct 02 14:55:11.152: %OSAPI-3-FILE_OPEN_FAILED: osapi_file.c:370 Failed to open the file : /proc/927/stat.(erno 24) *osapiReaper: Oct 02 14:55:11.152: %OSAPI-3-TASK_GETTIME_FAILED: osapi_task.c:3431 Failed to retrieve statistics (/proc/<pid>/stats) for task 'gccp_t' *osapiReaper: Oct 02 14:55:11.152: %OSAPI-3-FILE_OPEN_FAILED: osapi_file.c:370 Failed to open the file : /proc/926/stat.(erno 24)(code )
when present this loggs the device present those symptoms:
lost GUI session Lost console conection Lost SSH and Telnet conecction the WLC 4404 not work is stopedd
dns lookup failed, on all web browser (IE, Google, Firefox). I did ip and winsock reset, did networking ins safe mode, it will ping my ip address but will not ping any other address. My computer (running Vista home premium) says that I have internet access but it does not work. This happened on one computer and then on another one about 6 days later and they both are wired to a router.
I am running 12.3(11) T8 on Cisco 2821 platform and trying to upgrade to 15.0. No luck. So I tried to upgrade it to 12.4 24T. But failed several times on different routers. Is there an intermediate version I should land before jumping to 12.4 24T?
I got two offices about 150KM from each other,i need to backup 10 to 20GB / machine,the data ranges from accounts package to doc files etc.i suggested a vpn, then backup from one side to the other and vice versa as this ensures backups are swapped over and are off site.Would you recommend this, or am i better off using a hosted backup service i pay for / GB?
I am facing a failed issue when restoring the WCS Database. Below is the error i get, does any one out there facing it before?
####################################### [root@egwgwcs WCS7.0.220.0]# ./Restore Please enter the full path of the backup file name: /opt/WCS7.0.220.0/Backup_File/WCS_Aug2012.nmsbackup Untaring the backup file... Failed to untar backup file. Exception: invalid stored block lengths Restore database failed. #######################################
've used every version of ie up to 7 with no real problems, but I figured it had to be the browser, so I switched to Firefox. No improvement!Problems:When downloading (WinXP PC) online, suddenly all zips and apps (even Flash Player for browser) started showing "incomplete" or as it's called "Corrupt" files. One or two or maybe more small files would be left out. When finished downloading, it would say it completed the right mb's, but when unzipping or trying to install, there would be files missing. Tried "Repair" in WinRAR, no luck.
Region : United Kingdom Model : TL-WR940N Hardware Version : Not Clear Firmware Version : ISP : BT
I've been having some issues with my BT Broadband for a while, so decided to switch to a new router, a TP TD-W8960N, however setting up QOS isn't as easy as I had anticipated (I'm fairly new to this!).
My main issue is that we have a fairly limited broadband connection, but I need to backup work using backblaze. This is a pain because as soon as it starts to backup it eats what bandwidth we have. What I want to know is can I just limit the range of ip-addresses which they use for their backup?Is there a simpler auto-QOS approach I could use? The router is currently running the latest firmware that isn't in beta. Also - do these routers auto-update firmware?
I run a small organisation with 4 pc in LAN with a D-link DES 1016E router, and of course Internet connection through BSNL Broad Brand with a dynamic IP . Kordil EDMS, XAMPP is installed in one of this Pc with XP Pro SP3 and IIS7. I want to establish a easy and Free system through which i can connect my office server from anywhere through browser for editing ms office files at my Office network. suggest a step by step guide. I don't have any system administration knowledge. i have activated Remote desktop, but whenever i am connecting through internet my DSL router configuration page is opening.
My connection status icon has a big red x on it. I can't get on the internet. I tried the cmd stuff( ipconfig,netsh renewand release, and all the other jazz to do) my ip address starts with a 169 # I know that's not good. I go into my networks and I have no network. I go into my LAN ip4 and ip6and there are no addresses no were.I checked the LAN area status and it says not connected.
I have ACS 5.3.0.40 Primary Secondary Authenticators , of which the Scheduled backup has stopped.When checked the : Monitoring Configuration > System Operations > Data Management > Removal and Backup > Incremental Backup , it had changed to OFF mode. without any reason.Later i did the acs stop/start "view-jobmanager" and initiated the On-demand Full Backup , but no luck, same error reported this time too.
Rolled patch cable RJ45 to DB25M adapter (pinout from a cisco guide)
So far I am unable to get the router/modem to dial out at all. I know the modems work, I have tested them from Windows.
I have attached a couple of outputs from "show line" and "show line 1" from the router and also what I think are the relevent lines of config although it will be too much config and probably jumbled by now as I've tried quite a few things to try and get this working.
I am more concerned with the config relating to the connection of the analogue modem than the routing element.
I've been working on my laptop recently, once finished i turned my computer off like most people do. After turning it back on hours later, i noticed that my laptop was connected to the internet router but had limited access which ment i could'nt get onto the internet ! So when I went onto Network and sharing center and nothing came up apart from ''the dependency service or group failed to start'' ...I don't want to use system restore or reset tools of windows
DHCP Client and Network Location Awareness aren't working. When I tried to start DHCP Client, I got Windows could not start the DHCP Client service on the Local Computer.Error 5: Access is denied. I checked the dependencies and all of them were on. For Network Location Awareness, I got the error Windows could not start the Network Location Awareness on Local Computer. For more information, review the System Event Log. If this is a non-Microsoft service, contact the service cendor, and refer to service-specific error code -1073741288. One of its dependencies is fine, but I don't know how to check the other two, Ancillary Function Driver for Winsock and NetIO Legacy TDI Support Driver. Also, how do I check the event log?Everything on the list that was said to check is running expect these two the lisie was having problems with. I have not had anything with memory recently and have not been able to successfully go through a system restore. I have tried many of the suggestions and just am not sure what to do anymore. The computer works perfectly fine, minus it cannot get on the internet.
when I made the purchase for Linksys X3000. However, when I reached home and tried to use it. It auto reboot every 1 or 2 mins of usage. It's not just wireless affected but the whole thing rebooted. Reflash the fimware doesn't makes much different. Did a Standard 30-30-30 reset didn't solve any problem. Logged the case and informed linksys customer service that I'll go down to the retail shop for replacement. Case ID Given.On the 8th Nov, I went back to the retailer shop and proceed to get a replacement. The shop was fine, they allowed for one on one replacement. However problem persist. This time it got worse, when I tried to flash the firmware, it got stuck at 98% for half an hour. So I got it rebooted. Next, It can't boot up and the power status shown Red color.
I contacted the same customer service and inform them about the same issue with the replacement. Next I was given the address of the RMA Office at Funan L5-K3. Problem is, the address and location is wrong, the office became a Kawaii Koochi cosplay dessert shop.On the 10th Nov 2011, Checked the address in the net and some stated it's in Bishan and some stated it's in Funan. I called the Number given by the customer service and the line is dead. Called again, this time its Indian CSO and was told by the customer service that they're not operating after 7pm. But the problem is, it's only 5.30pm. Apparently they thought I was in US or Canada. So they transferred me to another customer service but nobody picked up the call. The fella just told me that hey, they not picking up so there's nothing he could do and that's it.I called a number started with 800-1204280, they told me that the office location is in Funan lvl 6 just beside the huge challenger store. I went down again at about 6.30pm and managed to locate the Service Center, I think it's third party as it cater for other product such as lenovo and other brand.This time the RMA center customer service told me that they doesn't carry any stock for replacement. I wasted so many trip just for one router. It's a very dissappointing service overall and this product is highly unreliable.
we have approx. 70 Cisco 1941W routers deployed in our company. I used to be able to console into the internet wireless AP by issuing the below command:
service-module wlan-ap0 session
However lately this hasn't been working and AP just simply refuses connection. Here is what I have for Status. I have tried reseting the Service Module to no avail.
Router#service-module wlan-ap0 status Service Module is Cisco wlan-ap0 Service Module supports session via TTY line 67 Service Module is failed Service Module reset on error is disabled Service Module heartbeat-reset is enabled Service Module is in fail open Service Module status is not available
How do I do a remote backup to an IP address? I am using NAT.I will be using port forwarding.I am using the windows "Add Network Location" wizard.I typed in my router's IP address, and it doesn't like it.I would like to run a backup by selecting the destination as this network location, if possible.
After I initial MSE with the wizard. MSE take so long to start the service (more than 1 hour) with "Starting MSE Platform, waiting to check the status"Then I decide to reboot the appliance, after that MSE shows the message "Traceback (most recent call last) File "/usr/sbin/yum-updatesd", line 40, in ?import gaminImportError: No module named gaming.
I have got a 1TB external HDD...I want to use this to backup my data (dokuments , pics , video) that are on 2 desktops and one laptop---
AS I understand the terminology a I won't have enough room to do image backups (these back up all info incl OS ??) as on pc is usingb 677 gb and the other 400 gb ---- and anyway I can re-install windows if anything goes wrong...
SO---am I able to do this-
1. connect the ext- HDD to PC running win 7 64 bit....create a folder called "win 7 64 bit" and then drag and drop filesand folders into that folder(or use windows backup..which i am unfamilar with)
2. then connect to PC running Vista 64 bit ..create a f�lder called "Vista 64 bit" and do as above....
3. Do the same for the laptop running win 7 32 bit
Am I right in assumming that because it's just data I can put info from different OS on to it without and conflicts when connecting it to different Pc's?
I have decided to set up a simple network at my home. I have got 2 PC's (one ground floor, one up staris), printer, TV and router.Now, my router has got only 4 sockets for RJ45 (no usb connection available). My target is to have one storage hard drive of 2TB for sharing pictures, files and automatic backup from PC's. Make of my router is D-link DIR-615. I want to have PC's connected by RJ45 for quick file transfer and TV as well to load movies from external/network hard drive so 3 of 4 ports are already used.I want to have my printer online in network all the time, so any PC can print at any time without connecting USB cable. Also I do not want to plug my printer into PC downstaris and share it in the network because if PC will be switched off, PC upstaris won't be able to print. So I want all my devices have connected to the router. Printer does not support ethernet interface as well (only usb connection).I've got a choice to buy an External Hard Drive (USB) or Network Hard Drive. I have choosen these two:
[URL]
As I said, I got 2 devices to connect to my network, and there is also one port available. I know, we got many different hubs etc, but what about printer? It supports only USB 2.0.I have also found very basic NAS on ebay:
[URL]
I thought I could by external hard drive because it is cheaper than network, and connect it together with my printer to this NAS and then NAS to router. Will I loose file transfer speed?
My roommate and I are trying to set up the internet, but my computer won't detect the Ethernet Cable. Whenever I go to Network and Sharing Center and try connecting to the internet, the computer simply says "Windows did not detect any networking hardware", even though the light is clearly on and should be working. The cable is also new so it should be fine. I've also been looking around on the internet a bit, and in trying to fix the problem it looks like some of my Services are turned off, which seems to be causing the problem. However, whenever I try and turn them on, I get an error message saying "The dependency service or group failed to start".
I have this idea of using my old computer (which is still pretty awesome) as a back up + production server. What this would entail would be that each person in my house has a dedicated hard drive that auto-syncs folders they've selected for backing up (not Memeo under any circumstances!). Then there will be a hard drive for me to work on web projects on. I'd like this computer to be very secure but if needed, I could show my work on the production drive to my boss.
i have tryed starting it on the services but that willl not do it eitheir. i have tryed almost everything and it stilll does not work. i can not access internet. plus i think a virus messed up my internet protocols. i think i removed the virus though i have been looking for an answer for 7 hours now
Do the problem caused by the modems itself or it just sign of faulty Ethernet switch (using 20 port Allied Telesis ethernet switch). Sometimes I cannot connect to internet due to "unidentified network" buy i can resolve this problem by restarting my modem + switch.
It is understood that sub-50 ms ERPS convergence can be achieved with certain HW/SW combinations.
1) What are the platforms supported (and with what FW/SW) has this been tested ?any results that can be shared?
2) Link failure detection in GigE on Copper is slower compared to GigE over "pure" Fibre; so no sub-50ms would be possible with Copper ring ports.is sub-50ms convergence achievable with "combo SFP ports" ?
I find it hard to understand tunnel and transport mode, the differences between them, and NAT. Ok so I have this scenario: Site2site VPN with 2 Cisco routers.
I'm now trying to implement a IPsec VPN network over transport mode in my simple network environment.I got two Cisco 2811 routers connected each other and each router hosts a client PC running Windows7.
I have finished the configuration on both routers and make them running over transport mode.However, as what it should be, transport mode indicates the communication between two end stations (two PCs) the client PC (install or configure something) to make the network fully works?
I would like to transport two time slots (TDM traffic) over an IP network in order to connect two telecom devices located in different sites, i have cisco 2811 routers on both sites with ip advanced services 12.4.20T IOS
