Can Connect Through Wired Connection But Not Wireless?
Feb 5, 2012
I can connect my xbox with the ethernet cable, but i am unable to get it to connect wireless. My laptop & phone are able to connect, I did try the steps such as resetting network configurations, i tried unplugging the router, i know my password is correct. i tried putting in the ip #'s. the xbox is not the only thing that won't connect wireless, neither will the ipod or kobo. it has been suggested that my router may be set for only a certain # of connections?
I'm a college student residing in the dorms a I did last year and over the summer. In both cases i had to move to different housing and internet connection went without a hitch. However i'm now at my new place, and i cant seem to get my desktop computer to connect to the internet. After 8 different campus tech crews came through, they've determined that the connection issue is not caused on their end. The issue as far as i can tell is not caused by the cable either because i got internet access when i bridged the connection using my laptop's wireless connection. I have also used the cable to connect to the internet on my laptop. However, when i try to connect on my desktop it says that that ethernet cable is not connected. No link light comes on, and the connection is not recognized at all.
I am using Scientific Linux 6.2 (Variant of RHEL / CentOS) . Every day at a particular time there is a power outage at my place, and after 1 hour power is restored. My laptop is connected to a network switch, that has no Backup power, and connection is disconnected when power is gone. Laptop keeps running in battery power.
Now when power is restored, the ethernet connection (eth0) is not automatically restored in linux. It only says connection available under wired connection. The same thing happens to the Wireless Network Connections. What can I do to automatically connect to these networks, whenever they are available?
I have a WAP54G in my basement shop, wired to our main router upstairs, which is a Linksys BEFSR81. I'm not sure if this is an issue with the WAP or the router.
I only use the laptop computer in the shop every couple of days, but I leave the laptop plugged in and on most of the time. I used to have the power settings such that it didn't power down completely even after a long time. With that setup, if i didn't use the computer for several days, it would find that the connection to the router had died. The wireless link would report that it had a solid connection, but I couldn't connect to anything. Power cycling the WAP always fixed this.
Recently, I decided to save some wear & tear on the laptop drive, and adjusted the power settings to go to standby after a couple of hours. Now, it seems I can't even go one day without losing my connection.
I am running the latest frimware in the WAP, and the router is version 3.1. I can't check the firmware version on the router at the moment, because the web interface is giving me a blank screen. I know from past experience that I will have to power cycle it to get it to talk to me again.
In any event, it seems like the router connection to the WAP is timing out. I set the router "client lease time" up to 10000 a while back when I first had this problem, but that is clearly not doing the trick.
I came here after spending a long time of trying to figure out my problem. The problem is, my router will send a signal strong enough to my room because of the thick walls. I have a wire in my room that I connect to my computer for internet. I also have my xbox and other internet enabled devices that I would like to use. Is there some way I could buy a router for my room that gets the internet from a wire? Could I use my computer as a router?
I have a wired connection & i bought a laptop can i have a wifi & wired connection at same time or can i connect my wireless router to my wired router?
I'm able to access the internet through my wireless network on my laptop, but not on the computer I have wired straight to the router. Isn't that weird?
I tried to set up a wireless router yesterday and when trying to connect with my laptop it had limited or no connectivity. I tried a few things but I couldn't get it to work so i switched back to my wired connection. Trying to set up the wireless router is not my concern though at the moment. Now my desktop can connect to the internet but my laptop and ps3 can not obtain an ip address. My desktop does not have a wireless card, thats the only thing I can think of why it will work when the other devices dont.
Right now I have my cable modem hooked up to a D-Link switch with my desktop and laptop connected. The desktop can connect and I get a limited or no activity with my laptop. I have reset the modem multiple times, restarted computers, Right clicked on my connection and tried to repair it, connect the laptop straight to the modem and did all of the above again. The IP and DNS are set to obtain automatically. Nothing is working that I know of but I can plug in my desktop and its up and going in 2 seconds.
The router was a very old one given to me from a friend. Its a Linksys V1. It is not connect to anything or even on now. The last time I tried to use this router I didn't get it to work and this same thing happened. I took it into work the next day and they were able to connect via wireless and wired using my D-Link switch. When I got home it work again just fine.
Just 2 days ago I realized that the wired connection will not let me connect to the internet at all. However, I have a wireless connection and it lets me connect to the internet. I don't like using the wireless connection unless necessary. I tried updating the drivers and troubleshooting, and it still won't connect. It still has that exclamation mark for the wired connection. I use a Windows 7 laptop.
I have wired LAN connection from my neighbour's router, and it is connected to my desktop. I somehow got the wireless connection to my laptop from the same place by entering a security number. I got the number through the wired connection as well. It was working perfectly working until recently. Now I cannot access the wireless, whereas my wired connection is working alright. is there any other way to connect this without asking the neghbour?
I recently purchased a 20ft Ethernet cable to speed up my internet connection. On wireless, I would download files at about 2 MB/s. On wired I get 1.5 MB/s. Is it supposed to be like this
My daughter is going to Uni and has wired ethernet access in her room but no wireless. She would like wireless so a) doesn't have to bother with cables and b) can use the WiFi for her phone.Would it be simple enough to plug a wireless router into this ethernet connection and set up her own SSID/Passwords?
why my wireless connection on my laptop is significantly better than my wired connection to my desktop. Internet ran just fine on the desktop at my old apartment; got to the new place, and now it's having serious issues.
After working on this problem for a while, I have come to the conclusion that for some reason, I am getting serious packet loss, consistently, at a particular "hop" on my desktop, which is not present on the laptop.Here are the Line Quality tests that illustrate the problem better than I could ever describe it in words:
Laptop: Line quality test packet loss and latency | DSLReports.com, ISP Information
Desktop: Line quality test packet loss and latency | DSLReports.com, ISP Information(and it appears they both fail the initial test, but the laptop connection runs just fine).
So at that one specific hop (ae-1-0.cr0.chi10.tbone.rr.com, I have no idea what that means), my desktop connection suffers serious packet loss while the laptop is more or less OK.This discrepancy is evident in the quality of connection on my desktop, while the laptop runs just fine. Here, in summary, is what I have tried:
-Going wired through laptop using same cables, ports, and router as desktop: laptop performs flawlessly.
-Updating router firmware, NIC card drivers, and Windows on the desktop
-Full virus disk scan and boot scan using Avast; full malware scan using Malwarebytes; Windows disk defrag
All of these actions together have made the desktop connection USABLE... however it is by no means an acceptable level of quality for a cable connection, and not nearly as good as any other in the apartment gets using the same connection, whether wired or wireless.The only visible difference I can find between the laptop and the desktop is the packet loss that is present at that one hop in particular, which is extremely debilitating for the desktop's connection.
Further info:
Desktop specs: Realtek PCIe GBE Family Controller NIC (onboard on the mobo) Windows XP Home Edition Version 2002 SP3 Intel Core 2 Duo E8400, 3GHz 2 GB Ram Plenty of Disk space
Router: Belkin F5D9230-4 Wireless G Plus MIMO Router
Here is the previous thread that details my troubleshooting efforts thus far; as the question has now become something entirely different, I thought it more appropriate to make a new thread. Wiresless faster than wired connection
Recently I installed connectify because my uni flat only had one wired outlet, and I wanted to use my xbox at the same time. It worked perfectly, but when I returned home I found my laptop could no longer connect to the home network, it just says it cannot connect, but all the over devices in the house work. My laptop can still connect to the internet via an ethernet cable but this isnt practical at home. I've uninstalled the connectify program, and tried my best to make sure I got rid of all the stuff it's done, but still my problem persists
I have 3 PCs (win7-64) connected to a wired gigabit network to achieve fast transfer of large files. Separately, at a distance, I have a modem-router to access the Internet. Internet access for the 3 PCs is achieved with each PC connected wireless to the latter modem router. The 2 networks are running OK and PCs can connect each other on both networks. Question: How can I know and achieve that the gigabit network is used for file transfers and not the slower wireless network? How should configure both routers and PCs to achieve this? I don't need the wireless setup to be a network, just to provide wireless access for each PC and that's it. I used to have the gigabit LAN configured with a Dlink DAP1522 bridge that created a single wireless connection between this wired LAn and the modem-router but it stopped working and I'm pretty done with it.
Once again the sun sinks into its nightly reprieve; for the third time since I first set out on this mission. Before me, only the piercing glows of monitors that sting my eyes. Yet, I cannot look away. The clacking of keys, once triumphant battle drums of purpose, has grown sharp. They pierce my ears and my mind. It would be madness to continue. My body is weak. My resolve is waning. My sanity ...... tenuous. But if seeing this through means madness.....bring on the madness.
I'm trying to find a way to network my desktop (wired) and my laptop (wifi) so that I can swap files between the two easily. I've mostly been attempting this through Windows Homegroup, although I've also downloaded and installed TeamViewer. The thing is, the two just will not connect. After much poking around I found the specific symptom to be that wired connections and wireless connections refuse to speak. My laptop sees my roomie's laptop easily enough, though. And if I hardline my laptop to the router suddenly their best friends! - joining each others' Homegroup, swapping files, trading recipes!
Points of interest: I've noticed that, while both are enabled, only IPv4 connectivity indicates internet access; IPv6 says No Internet Access. Pings from one machine to the other result in "Request timed out" or "Destination Host Unreachable." I've disabled firewalls - Windows and the one on the router. Disabled and then uninstalled anti-virus. I've updated the router firmware and net adapter drivers I tried restoring router to factory settings, in case I changed something I shouldn't have along the way. I've alternated static and dynamic ip addresses - no difference there. I've just spotted a couple of errors in the Event Viewer that look like they could be leads;(!)ErrorDhcp-Client The IP address lease 192.168.2.2 for the Network Card with network address 0x6CF049E337F0 has been denied by the DHCP server 192.168.2.1 (The DHCP Server sent a DHCPNACK message).
I am getting ready to move into new digs and wanting to set up my network. Main house cable internet will come in with modum to a dlink router for both wired and wireless. desktop and a magic jack wired into router wireless for ipad and laptop. then run wire to workshop about 100' from house where a second magic jack and desktop will be set up (small biz out of workshop). I am pretty sure that the range of the router for wireless will reach to workshop fine for ipad but if not I will need to put a wireless up there tooext kids have a laptop running windows 7 but kids being kids and having had problems with self control on net in past I want to be able to make sure that I can turn them off from net when needed because
1. I do not want them running me past the data limits imposed by cable company and 2. keep them from sites such as those which got them in trouble in the past (kids are older and bought laptop for selves and pop will not go along with me confiscating it if they abuse internet privileges
I have a laptop running win xp. It was running fine this morning. I then brought it to a Honda dealer. The problem started there ...At first, I got a strong wi-fi signal but not network connection. I tried to repair (by right clicking on wireless network icon on the lower-right corner). The first time it seemed trying to do something but nothing worked. The 2nd time when I tried to run repair, the process hang and the machine could not be rebooted or shut off. I have to hold the power key for a few seconds to turn it off.Now, I am at home using another computer to post this message, which indicates my home lan and my router are working fine. But my laptop still has no connections - neither wired or wireless
I have two computers that both have wireless and ethernet cards. When they are btoh wirelessly connected to my router everything works fine. However, the speeds are horrendously slow. So I want to be able to connect the two of them with an ethernet chord.
I set it up so the computer with the better wireless, I'll call it PC2, is sharing its connection and I have the wireless on the other computer, PC1, turned off. I can freely access the internet on both computers with no problem.
This happens on both computers: I goto the Networking page and the other computer shows up. I double click it and I get the 0x80070035 error. Both computers can ping each other, but nether can ping the others host name. So I can ping 192.168.137.1, but not \PC2. No firewalls are running. If I turn the wireless on PC1 back on, it works again, but with the horrible low speed.
I have two separate wired networks. Network 1 has a wireless router (an adsl modem). Router of the Network 2 is not wireless. Can I replace router of network 2 with DIR-600 to make a wireless connection between these two network segments ?
I originally installed my DIR-655 as a wireless access point, not using the wired ports at all, and it worked fine like this. Trouble with my trying to set up my Bell router/modem with port forwarding prompted me to change my configuration so my Bell router /modem is now only a modem, and I am using the DIR-655 as a wired as well as wireless router. I have a separate network server and so don't use the DHCP on the DIR-655, and I only use one port to connect to a separate gigabit switch that serves the network.
I am finding that the wireless connection works really well with the few wireless devices I have connected (mainly an apple tv, and a MAC book) but my wired connections to the internet "feel" slow, sometimes with a significant delay before links to sites are established. I click a link, and wait for several seconds before the site shows up in the browser; sometimes after that the same site seems to respond at normal speeds, other times there are added delays.
Is there something in the DIR-655 settings that would cause this? The wireless connections seem fine.
Should I be looking at a new router/modem (rather than separate boxes)? If so what would be the equivalent D-Link model?
My D-Link DIR-300 very often loses connection on wired and wireless connections. It stops connecting to Internet randomly i.e. any URL typed in from the browser times out.I connect various devices such as desktop, laptop, ipad2 over wired and wireless connections and the behavior is the same from all devices when this problem occurs. If I make a direct connection to the DLS modem, it works fine for the whole day, without these issues.I also observed IP address conflict messages and my desktop does not connect to Internet if I am running VPN on my laptop, at the same time, occasionally.When this occurs, I am able to login to the router and can see the WAN status and the DHCP address being allocated to the router. I can even do DHCP release and renew, but that does not fix the problem.
My sister has just purchased a custom built desktop computer that will not connect to the household network. We have various other computers and devices that connect to the router (Thompson Gateway TG782T) without any problems. Just to be sure I've tried reseting the router to factory settings to no avail.
I've tried connecting her computer to the network through the TP-Link Wireless Adpater (TL-WN881ND) that came with her computer AND through a Netgear Wireless USB Adapter (WG111v2). In both situations the network is detected, the network password is requested (and accepted) but the result is always that she has 'limited connectivity', cannot access the internet and cannot detect any shared network drives.
I've tried connecting with an Ethernet cable as well, which her computer does not detect at all ('network cable unplugged').When I try to troubleshoot any of these problems I get a message that says 'The Diagnostics Policy Service is not running'.The guys at the shop where my sister had it built are asking her to bring the computer in with the router becuse they are convinced that the machine is fine, and that the router is at fault. Some Specs for her computer
------------------- Windows 7 Professional Service Pack 1
I have a Linksys WRT54G2 router upstairs in my house that wirelessly reaches the entire house. I also just bought a Linksys Valet Plus M20 that will be my router once I get it in the mail. The problem is I want to hook up my downstairs Satellite receiver to the internet but it only has a LAN port. I cannot run a LAN cable downstairs. Is there any way to link these routers up wirelessly and then run a LAN cable to my SAT receiver? Or do I need to buy a different product?
I have 3 computers running Windows-7. One computer is directly attached with wired connection to broadband internet modem and other 2 computers are attached through a Wireless router attached to modem. The problem is this that both wireless computers are running internet well while the directly connected computer shows internet connection but no data flow happens. When the Wireless router is turned off the directly connected computer starts working internet.
I'm having trying to connect my Samsung Smart TV to the Internet.I purchased the Samsung EH5300 yesterday and have connected it to my router (ZyXEL P-660HW-T1) via Ethernet. This works fine and picks up all the settings (ie: IP address, gateway etc) automatically and I can connect to the Internet fine.The problem comes when I then connect any device to the router using Wi-Fi - this could be my iPad, iPhone, PC, laptop - anything will disconnect the wired TV connection immediately from the Internet but it DOES NOT disconnect it from the network. In other words, I can still see the TV in the list of devices on my router and still ping the IP from my PC. All the settings on the TV remain the same but when running the network test, it says it is connected to the network but not the Internet.I have disconnected all cables, reset the router, turned everything off and on several times, placed the Ethernet cable in different ports on the router, manually input all the IP addresses etc but none of it is working.
I am looking to get a wireless card to share my wired desktop connection for my tablet, laptop and phone and xbox 360 slim. A wireless router would seem the obvious solution but the accommodation I have at uni charges £15.00 just to allow a router to be used.
I'm capped out at 12 mbps service through Mediacom. My PC is directly wired to the WRT120N. I consistently test in the 11 mbps range.
I have a very unusual issue though.
I can connect my iphone and Xbox wirelessly through my router with no issues on their side. However, any time I do so, it kills my wired connection on my PC. I'm not doing huge downloads or P2P or anything like that. In fact, the speed drops immediately on my PC the moment I connect my phone to the wireless network regardless of what i'm doing on the phone (checking email or loading a webpage).
