Linksys Wrt54g - Supply 3 Pc's With One Wifi Signal From Usb Wireless Adapter?
May 15, 2011
My cable went out and my neighbor and I have decided to split her at$t broadband, the phone/modem/router is a 2wire.
I have 3 windows 7 computers but only one wireless g usb wireless adapter from tenda. I also have a linksys wrt54g wireless router that I can use.
I have tried to set up the router as a wireless bridge by loading a DD-WRT bin on my linksys but it seemed way buggy -results - I was only able to get 2 of 3 online and if I restarted any of them I lost the connection completely.
Went back to stock firmware and tried to set up a lan between the 3 towers with the linksys then just bridge the two connections on the main pc - results -no internet at all on 2nd and 3rd pc... and when the connection to the wifi network is started I loose my networking to the 2 pc's on the linksys.
Im not sure if im not setting these up correctly as im just following guides and such but since im fairly good with computers this is making me crazy...to be able to set three computers up on 1 good clear wifi should be an easy task but it's just not working out..
View 1 Replies
ADVERTISEMENT
Aug 27, 2012
I recently bought the top end ea4500 hoping its "high end" claims would get a better wifi signal in my bedroom(on my iphone 4s) than what i was getting with my WRT54G.The end result is it constantly drops signal completely or shows my network but when I try to connect says "cannot connect to wireless network" even though it's staring me right in the face. When I hook my WRT54G up, I get a signal.. all be it weak, but at least it doesn't drop out on me.Did I just waste almost $200 on a high end router that can't push a signal out stronger than my almost 7 year old WRT54G? or am i missing some setting that will make this EA4500 worth its claims? settings info:everything is pretty much on "default" aside from the SSIDs for the different bands and the corresponding WPA passwords.
also another problem, it seems like the router itself craps out every 60-120 minutes, no leds lit up on the router and my modem (Cisco DCP3010) shows no "link". Yet when hooked directly to the PC there is a "link", so pretty sure its the router and not the modem.
View 9 Replies
View Related
Dec 8, 2011
New wireless router was installed yesterday. I switched from Linksys WRT54G v. 5.0 to Medialink N. I hardwired to desk top first. Then I turned on my laptop and connected to the internet without problems. Next device = Acer Aspire netbook. The netbook receives a strong signal from the router but cannot connect to the internet.
View 1 Replies
View Related
Jun 6, 2012
I have a linksys wrt54g wireless router and a few weeks ago my wireless connection started to become inconsistent, it would randomly drop service or be very slow, and now it has become very inconsistent and slow, all the while the wireless signal would be 4-5 bars.On my windows 7 desktop, often times the yellow triangle with the exclamation mark pops up over the signal strength indicator when its at 4-5 bars.I've tried changing to 2 different routers and its the same, and the problem is persistent for all computers in the house.I've connected directly via ethernet to the modem and router and service was fine.There are a few wireless networks in the area,some with quite strong signals, but I downloaded the xirrus wifi inspector and it says I'm not sharing a channel (channel 1) and though I'm ~15ft from the router, the signal is ~65dbm, which seems low and is almost equivalent to neighbor's wireless strength.
View 2 Replies
View Related
Oct 16, 2011
My wireless router has been spotty since my cable company installed a new modem for cable internet. I have powercycled several times, downloaded new firmware, rebooted and am still having problems. Lately when I do finally get on the internet with a wireless device, the signal strength is very low. It is low on my iphone, on my Mac laptop and also on my Samsung Bluray player. Lately a window keeps popping up when I am trying to watch netflix that states my band width is too low, even though it has been working fine for 2 months. Is my router outdated?
View 5 Replies
View Related
Mar 25, 2013
it might be good to point out first that this was never a problem before i began fixing a completely irrelevant problem (screen broke) with my laptop, which took around three weeks. i could at that time use the internet a couple of rooms away from the router just fine, but now it's a no-go. .
the model is WRT54G, and the serial number is CDFD1F9CJ507.
View 1 Replies
View Related
Feb 4, 2011
I have a Linksys wireless-g broadbrand router ( WRT54G ) in my bedroom along with my cable modem and everything runs fine in my room. But I also have a pretty old computer in another bedroom about maybe 15 or 20 feet away from the current setup. On that computer I have a wireless g adapter that's connect through a usb port and has very low signal strength. I sometimes use that computer and I'm always getting kicked off I'm guessing because the signal cuts out. So, today I plugged in the adapter in my room with my setup and had amazing signal. What can I do to give that other computer a good boost? I know I should update that computer but I'm guessing I also need to somehow boost the signal somehow.
View 6 Replies
View Related
Jan 2, 2013
Is it possible to configure the WRT54G as a repeater signal of the WRT120N?
View 1 Replies
View Related
Oct 17, 2011
I am having problems connecting to my wireless internet. We were getting a poor signal so we moved our router to our living room where we always are, but now we can't connect. We tried resetting everything, turned on and off several times. Went to the linksys wireless set up page, changed SSID and password. Still can't connect with the computer or our iphones. It shows our SSID is there but won't connect. My internet when plug directly to the computer works fine (I am using it now). My computer can connect to the router Linksys WRT54G, we just can't get it to connect to the wireless.
View 1 Replies
View Related
Jul 11, 2011
I have a office that was converted from a older townhouse. The building has 3 floors with the distant of each floor expands no more than about 60 - 75 feet from end to end of the building. Not sure what's in the walls as the building is at least 20-25 years old. Total number of users is about 20 - 25.
Here is the problem..
I have a WRT54G wireless router setup to provide wireless coverage for this office, located on the 2nd floor, For some reason, about 10 - 15 feet from the opposite end of the building, the signal drops off big time. Regardless of the floor. So to assist with the signal, I installed a wireless 300N Gain extender on the same floor on the opposite end of the building where the signal was weak. At first, it seemed to work by boosting the signal, but then it seems to show the same issue as before.. sporatic signal loss, signal fluctuation, etc.
My question is should I replace the wireless booster with multiple wireless APs located throughout each floor... maybe 1 per floor? If so, is there a trick to configuring all 3 APs to have the same SSID and same encryptionsso it will be seamless to the users? Since the first AP works fine, I wanted to get 2 additional WRT54G units.
View 2 Replies
View Related
Dec 26, 2012
My old WRT54G V8 router has been acting up lately. It keep dropping the connection out of the blue. Sometimes I'd be browsing the Internet when the router's signal vanishes completely, it disappears from the list of available wireless networks on not just my computer, but my smartphone and all other devices in the household! Other times I keep connected to the network but there's no access to the Internet. Everything seems fine on the ISP's part, I can connect just fine directly from my modem, so I'm certain the problem is with the router. Besides, these problems are solved by just power cycling the router.
View 4 Replies
View Related
Jul 31, 2012
I have a LinkSys WRT54G Wireless-G Broadband Router located in my basement office. My IBM T42 ThinkPad running Windows XP Pro has an Intel(R) PRO Wireless 2200BG Network Connection adaptor. The signal strength on the main floor of our townhouse is ~ 80%. My problem is the signal frequently disconnects then recovers automatically causing frustration when browsing the internet. My question: Should I upgrade to a new Wireless N router OR purchase a WiFi Range Extender? since my laptop has a Wireless-G adaptor would a Wireless-N router provide a stronger signal?
View 4 Replies
View Related
Dec 10, 2012
Have two WRT54G Wireless Routers.
-One WRT54G ver. 6, Firmware Version v1.028
-One WRT54G ver. 6, Firmware Version v2.x
With the WRT54G ver. 6, Firmware Version v1.028.When I ran the android app WiFi Analyzer, I get mixed results.On my Samsung Galaxy S3, I saw my signal on Channel 2, and others around me (two on Channel 6 and two on Channel 11).On my ASUS Transformer Prime TFT201 I see the same signals, but my router signal bounces continously between the baseline (-100dBm?) and about -35dBm.
Plugged in the WRT54G ver. 2, Firmware Version v2.x Channel 8.Hooked it up and got good steady signal strength. It Had 'WPA - Shared Key' but did not have the 'WPA - Personal' that was on the ver. 6. So, I had to go and screw things up. I've upgraded this to Firmware Version: v4.21.5 and guess what? I now have 'WPA - Personal'. I also have a signal is bouncing on BOTH units.
On my ASUS, I can see both routers. The ver. 2 AND the ver. 6 are bouncing between baseline and -35dBm, in unison. Apprently something in the ASUS does not like the later Firmwares.On my Samsung I can see the two signals - the ver. 2 on Channel 8 is stable as a rock and the ver. 6 on Channel 2 is also bouncing, but at a much slower rate! Running Speedtest.net a PC hardwired to the ver. 2 - I get 5.34 Mb/s Download and 0.47 Mb/s upload (yeah, my Internet sucks!) Running Speedtest.net through the ASUS/WiFi to the ver. 2 - I get 2.43 Mb/s Down and 0.65 Mb/s Up.Running Speedtest.net through the Samsung/WiFi to the ver. 2 - I get 5.07 Mb/s Down and 1.07 Mb/s Up.
View 6 Replies
View Related
Aug 17, 2011
how do i setup a wrt54g router as a wireless access point to extend wifi signal from e3200 which is broadcasting the internet?
everyone keeps saying to remove the stock firmware and instal the dd-wrt firmare to do this. can i do this with the stock firmware?
View 1 Replies
View Related
Apr 6, 2011
I lost my power adapter for the WRT54G router. I have a 12V / 1000 mA brick adapter.
View 5 Replies
View Related
Jul 20, 2012
I'm finally upgrading my internet from my currently pathetic 1.5 mbps to a robust 20 mbps cable connection. It's getting installed over the weekend and my question is, should I try to place the modem close enough to my pc for a direct ethernet connection, or will wireless be fast enough to take advantage of the full 20 mbps? I have a linksys wireless-g wrt54g router. It says it's 54mbps so it should be far beyond my cable speed. My adapter on my pc is a Netgear WNDA3100-100NAR dual band usb 2.0 wireless N adapter that claims up to 300 mbps. So it seems like I should be able to achieve the same speeds wireless or wired, but really don't know much about networking other than basic router setup so wanted to double check. It will be a bit of hassle to try to route the modem into my computer room as I don't have any lines run there currently. If I place it by the tv and go wireless it's a lot easier setup.
View 4 Replies
View Related
Oct 2, 2012
I am looking to upgrade my home wifi from a Linksys WRT54G running DD-WRT to something that will handle .11n. I've been looking at the Unifi PoE APs. Their base model support N, but only on 2.4GHz, and only has a 100Mb port. I was concerned about that being a limiting factor. They've recently released a new line that supports Dual Band and has a Gig port, but it cost about 4 times as much. Here are my goals:
1.) PoE if possible. Currently the AP is my rack in the basement. I'l thinking of running an additional cable to somewhere central on the first floor and putting the AP there for better coverage/signal. Running just a CAT 5e cable is much easier than having to supply power as well. Second thought was to get two Unifi APs and setup a mesh with roaming, which it looks like they support, for best coverage. In that case I'd put one in a top floor room that already has CAT 5e.
2.) I'd really prefer access points to a router. I already have a pfsense box that does the routing. If this means getting something that will run DD-WRT, Tomato, or the like and turning it into an AP fine.
3.) I would like something that is dual band .11n.
4.) Something that support RADIUS
5.) Multiple SSID support and VLAN support. I want to be able to offer at least 2 separate networks.
So am I stuck buying the Unifi dual band AP? Or should I get something like the Asus RT-N66U and put Tomato on it?Does anyone have acutal expreience with the Unifi products?
View 19 Replies
View Related
Aug 6, 2012
Can I use a Linksys WRT54G router to get a signal for my desktop? I am using a modem that has wifi downstairs and want to get a signal for a desktop I have in the kids room upstairs
View 4 Replies
View Related
Aug 27, 2008
Can you use your WRT54G router with the newer WRT310N router to extend your wireless signal? How?
View 7 Replies
View Related
Jul 20, 2011
Got a new e1000 after a RMA. The new unit has a very weak wifi signal. I've tried all different channels. It is running in mixed mode. No microwave, blue-tooth or other noise. 4 feet from the router and the signal is down to -90db. Take a few more steps away and the connection is lost.
View 2 Replies
View Related
Nov 24, 2012
I have Att internet services and the modem I received from them has WiFi with it. The signal that it produces is very weak. I was curious if there is any way to use my E3000 to boost or repeat the signal so WiFi will extend through out the house.
View 4 Replies
View Related
Nov 30, 2011
is it any possibility to set my router WRT54G V2.2 as a wireless repeater? and does any manual for this exist?
View 3 Replies
View Related
Nov 22, 2011
I am trying to connect a myTouchQ (t-mobile) through my WRT54G. The android shows that I'm connected and have a good signal, but I can't access the internet or any data. When I turn off the wi-fi connection, I can access through the 4G network. My provider is Cox Cable. I've unplugged the modem and the router for 30 seconds and even reset the security.
View 5 Replies
View Related
Apr 5, 2013
My wrt54g (firmware old - v1.00.6) has run fine for years until my daughter got a laptop with win7. All my other systems still run XP or win2k. I only run wireless with her win7 and one netbook with xp, all the other connections are wired.
Going to speedtest.net and after I reset (pull power) the router, I get 20Mbps download. After the win7 wifi runs for a bit, download speed drops to 2 Mbps or less. It seems to be after she goes to you tube and starts watching videos. If I reset again, it immediately goes back to the full speed of 20. I measure this after she's taken her laptop off the network. So, whatever her win7 is doing, it stays that way after she disconnects (i.e. slow on my other systems) until the reset. I also measured the speed on her win7 system and it also would slow there as well and speed up after a reset (for a while).
View 3 Replies
View Related
Nov 1, 2011
all other devices have excelent signal
View 5 Replies
View Related
May 6, 2012
My new EA4500 works fine all day, both wireless and wifi, on both bands, but nearly every evening, the wifi signal disappears, as shown on a wifi app for my smart phone, but not on Issid on my laptop, strangely, and my PC laptop and iPad both disconnect, then reconnect. Smart phone disconnects too. It isn't like the signal drops in strength, it just goes away! I have tried various settings on modes, and bandwidths, I am using different SSID's on each band, WPA2 security with a long non-dictionary passphrase and MAC filtering. The hardwire connection works great at 30+ Mbps even when the wifi is disappearing from the wifi scanner and the wifi connections are dropping. In other words, the cable connection/modem is working fine, but the wifi radio signal stops or the SSID drops off the signal. I really can't tell, but I know it is becoming very frustrating. The old WRT54GS works fine if I put it back on-line in the evening when these things start to happen.
I have turned off everything I can think of in the house that transmits or might transmit, in case it is an interference thing. I have tried disabling the 5 GHz side, since I can't see what is happening on that band, and the last thing I tried was changing the MTU from 1500 to 1400. So far, the past evening, it was okay, but I am not confident it will stay that way.
View 6 Replies
View Related
Aug 5, 2006
I've had a LinkSys BEFW11S4 wireless router for several years now -- ever since it first came out (this is a version 1, not even a version 2).
View 3 Replies
View Related
Apr 19, 2011
I've bought a E4200 router because of it's "maximum performance". With the normal settings i have a wireless range of maximum 10 m in the building. after 5m I've got a low signal.I tested a cheap Netgear-router, which had the same range as the E4200 a 125 Euro.Is my E4200 broke or is it just a bad buy? The settings are standard (that shouldn't be the problem, I guess!?)
View 9 Replies
View Related
Apr 27, 2013
I have the following equipment
E2500 wireless N router (2 of these)
WRT54g router (B/G)
WAP54g access point (B/G)
I am planning to set up a wi-fi network for a single story motel. It is C-shaped; about 300 feet along the longest side with "legs" of 120 and 70 feet. I have included a diagram that I drew for the person that will install it. Until now I have only used that single WRT54g in the office for the entire property and it covers about half the property (left side) but not well and with a dead spot in the top left because of too many walls to go through.
My plan starts in the office (bottom left) with a WRT54g connected to the DSL modem as it always was. That would be connected to one of the E2500s in the middle so it can cover the most area. From there two others would shoot out to each corner (the other E2500 and the WAP54g). They will all be wired together with Cat 5e "riser cable". The routers will be placed in a wide open attic.
1. Is this is a good plan for the size of property? I have heard that N routers have a range of 150ft in every direction so that's why I'm putting one in the middle. Keep in mind that while the attic is open and wood constructed, the walls between rooms are concrete firewall and they haven't been wi-fi friendly. Hopefully putting them in the attic takes care of this.
2. Does starting with a B/G router at the modem mean the N routers will revert to B/G?
3. What are the main settings I need to know about? What "mode" does each need to be set to? Do they need different default gateways?
Can I use the same password/security for all of them? Should I use the same SSID for all?
View 4 Replies
View Related
Aug 6, 2012
I've done a firmware upgrade to latest version v4.21.5 yet my Wifi still isn't broadcasting for my devices to find and connect as of last night (Aug 5, 2012). This hasn't happened before, so I was hoping it would return but still hasn't started working yet.My iphone just says "unable to connect."
View 4 Replies
View Related
Dec 1, 2012
I am having problems with connectivity and my iPhone 5. The Wi-Fi is okay in some parts of my home network, however in others it is abysmmal. When I bring my computer to the places where the iPhone has problems with signal strength/staying connected the computers have full or almost full strength and no problems. I upgraded firmware for the router, spoke with applecare, have reset the router multiple times, and have been trying different channels. I had the phone in with the Apple store where they concluded nothing seems wrong with the hardware. The phone doesn't seem to have problems like this on other wifi networks I have tried. Using a speed test on the iPhone at home in the low connectivity areas results in horrendously poor latency numbers.
View 2 Replies
View Related
Jul 20, 2011
My router's wireless connection goes down intermittently,about once a day. I can access the network with a machine that has a hardwired connection to the router only. To get it back up I have to perform the following steps.1) Reset the router.2) Go to the router web page, http:\192.168.1.13) Set router name4) Set router password5) Set wireless network name6) set wireless network secuity mode: WEP7) set wireless network password
LinkSys WRT54G V3.1 router with firmware update V4.21.1
View 2 Replies
View Related
May 26, 2012
DSL modem works fine when connected directly to computer. No internet output from WRT54G wired or wireless, but wireless network is recognized by computer, just no internet. I did a reset and installed the latest firmware, then I ran thru the setup CD that came withe the router, and the internet test said no internet connection was available. Cables are fine, connector innards look clean.
View 4 Replies
View Related
