I am attempting to setup an Apache Server 2.2 for Windows, everything is set up but the server will not start, I heard it may be caused by my virus protector using Port 80 but I cannot find the httpd.conf file for it in the directories they say it should be in, I even did a tree/f with CMD DOS?
View 5 RepliesDifferences between using an Apache server on a regular laptop vs. a whole operating system like Windows Server 2008. I'd like to setup an intranet complete with an internal domain name. Is this possible with Apache or do you have to use a complete server operating system like Windows server 2008?
View 1 Replies View Relatedi've created an application with NodeJS and I'd like to test the application on my LAN with my family. The application listens on port 1337 for connections and I can access the application fine through my own PC by typing localhost:1337, 192.168.0.3:1337 or even http://joel-pc:1337/ into my browser's address bar.
I will be also be running apache alongside NodeJS, and I can access this fine by typing 192.168.0.3 or http://joel-pc/ into a browser's address bar as long as it's connected to the same network.Now here's the weird part; If I stop the apache service, change my node application to listen on port 80 (http) insted of 1337, it will be accessible on my pc by typing localhost, 192.168.0.3 or even http://joel-pc into my browser's address bar. However, I still can't access NodeJS on any other PC on my network apart from my own.
I've tried creating an outbound rule within Windows 7 to allow access to port 1337, but I still can't get access to my NodeJS server on any other PC than my own, even if it's listening on port 80.
i've been using a VPN to connect to my home network from elsewhere for a few months. It's set up as follows:
PPTP
Maximum Strength Encryption
EAP-MSCHAP-v2 Authentication
Now I find out that MSCHAPv2 authentication has been broken and is no longer considered secure (even by Microsoft), so I want to change the protocol I'm using to make it secure.
However, I've spent 3 hours now researching this and I cannot for the life of me figure out how to use a better protocol on my Windows Server 2012 home server. I've tried setting up PEAP authentication (still PPTP) a la Microsoft's recommendation document, but it requires a certificate. I've created a self-signed certificate but it seems I can't issue certificates (via this method) without being a member of a domain, so I'm stuck. I can't even get started with L2TP since I can't find the option for it.
My question is this: Is there a way to setup a secure VPN server using Windows Server 2012 without a domain? If so, how do I do this?
i want to setup DHCP using my windows xp
View 1 Replies View Relatedi m having one static ipwant to create the network in computer labhow i do thisi have one cisco router assigned with one ip address
View 1 Replies View RelatedFirst network card have the static IP address 82.x.x.30 from the ISP.The second network card have 2 IP addresses: 192.x.x.0 and 82.x.x.1 ( first IP is for LAN and second IP is for routing the additional IP class).In other words if i have the computer "Z" with configuration: IP: 82.x.x.100 Sub: 255.255.255.128 and GTW:82.x.x.1 i can access the internet but practically with with the IP from ISP wich is 82.x.x.30
View 1 Replies View RelatedI would like to set up a home server, that will sit under the stairs so that it can link to out BT home hub (v3). The idea is then to connect the printer to it, so that we can have both a wireless printer and a central file store for pictures/vids etc.Is XP ok for this? if so, what settings do I need to change/add?Is there any software that I need to make it work?How do I make sure that it is secure for external hacking? As it will contain our personal docs/photos etc and I would hate to use them.
View 1 Replies View RelatedI am planning to implement wireless network in my work place. Plan is to have two networks one for guests and one for employee. I am trying to find a guide for 2500 WLC but couldn't find one.I've been reading couple of articles about setting up radius server and CA. I want to know what the best way to approach this.In my environment I got a CA server windows server 2003 and current DC's are windows server 2008 R2.I got 2500 WLC with POE switch and 4 aironet AS 1142.
View 16 Replies View RelatedI have assigned a task to configure a vpn between windows 2008 server and cisco asa 5505, what kind of vpn should i go with as the windows 2008 server r2 is on cloud and is it possible to configure site-to-site vpn for this network senario or not.. i have try ikev1/ipsec remote access vpn with l2tp with (CHAP, MS-CHAP v2) and couldn't find any document which will allow me to configure windows 2008 server to behave a client and connect it to asa, well what i did is that i configured a dail-up connnect with l2tp and found the following debug message
Sep 09 20:04:02 [IKEv1 DEBUG]IP = 172.16.32.5, Oakley proposal is acceptable
Sep 09 20:04:02 [IKEv1 DEBUG]IP = 172.16.32.5, IKE SA Proposal # 1, Transform # 1 acceptable Matches global IKE entry # 1
[Code].....
I am planning to implement wireless network in my work place. Plan is to have two networks one for guests and one for employee. I am trying to find a guide for 2500 WLC but couldn't find one.
I've been reading couple of articles about setting up radius server and CA. I want to know what the best way to approach this.
In my environment I got a CA server windows server 2003 and current DC's are windows server 2008 R2.
I got 2500 WLC with POE switch and 4 aironet AS 1142.
I am looking at buying the EA6500 router. However, before I make the investment into buying this router, I need to know some basic information first.
1. I want to setup the EA6500 to accept FTP requests to my Windows Home Server. Yes or No?
2. Remote access to the EA6500, Yes or No? i am aware of the security risks
3. I need to setup Port forwarding on the EA6500. I assume I can?
4. Manage a Kindle Fire and other wireless devices?
I planned for my customer to replace his old LMS 4.0.1 server under Windows 2003 by a new server under Windows 2008 R2.Customer wants also to set a new LMS name and IP address for the new server under Windows 2008 R2 and keep both servers on the network.I'm wondering what could be the best procedure to do that migration.Can I used backup / restore procedure in that case ?If yes, what file must I modify to adapt the new LMS configuration to new hostname and IP Address ?
View 2 Replies View Relatedi am trying to use teh ACE to replace an apache based load balancer in an jboss application cluster. I am using L7 loadbalancing to load balance between multiple components. the way these jboss application servers work with apache is that.When the jboss application starts up on the on application cluster, it issues a GET opencase/webservices/config-service?wsdl to the loadbalancer IP.The apache based LB in turn talks to the same box on port 8009 via ajp retrieves the configuration file and provides it back to the application on port 80.And after 2 has completed the Jboss application comes up. Basically to start the application the Apache loadbalacer will accept requests from the its target list and load balance the request back to them itself.Not sure how i can use the ACE to accomplish this. attached are my topology (logical) and the ace configuration. from my topology file -- the net-cms-1 will issue a get request to teh VIP (on the ace), the ACE accepts the connection but soon resets it.
View 1 Replies View RelatedI have installed lms 3.2 on server 2008 , and when I click on device update in software center I receive an error which I inserted down here ;I have to mention that I also have installed Common services patch .
View 8 Replies View RelatedI have taken over a couple of LMS 3.2.0 standalone servers (two different networks). When I reboot them they tend to be slow coming back up (20-30 min). I"m thinking this may be due to the fact that LMS was reinstalled on both of them as I see an old CSCOpx folder (CSCOpx_old) as well as the current one. I assume that someone reinstalled and the registry may be dirty and service dependencies may be jacked up but honestly I don't know how this works for LMS and I haven't found much good info in the user guide for common services for service dependencies or registry keys in general.
Also, one of the servers never comes up fully on reboot or restart of the daemon manager. I troubleshot this and found that Tomcatmonitor and Apache are always down after reboot/restart. Tomcatmonitor says that it was shutdown by the administor in a pdshow and Apache says that it was never started. I have to go into the server and manually start these processes with a pdexec to get the application up.
I'm trying to get a Curl Response from an outside server, however I noticed I cant neither PING the server in question nor connect to it.I tried disabling the iptables firewall but I had no success.My server is running behind a Cisco Linksys WRTN310N Router with the DD-wrt firmware Installed. In which I already disabled the firewall.
Here are my network settings:
Ifconfig
eth0 Link encap:Ethernet HWaddr 00:26:b9:76:73:6b
inet addr:192.168.1.120 Bcast:192.168.1.255 Mask:255.255.255.0
inet6 addr: fe80::226:b9ff:fe76:736b/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
[code]......
This gets an empty result array. This function however works well in the previous server where the script was hosted before. No modifications where made whatsoever
Essentially, I have a spare desktop computer I'd like to turn into a web server, but my modem and wireless router are very difficult to work with. I installed Apache HTTP and successfully hosted a test page which can be accessed anywhere on the LAN. However, I'm having trouble setting up the server to be accessed from my external IP address.
I was supplied with a ZyXEL EQ-660R DSL modem by my ISP (CenturyLink) and bought a Netgear WGT624v3 wireless router in which to connect my laptop and spare desktop.
ZyXEL's website is not useful, and I don't think much of the problem is with the Netgear router. I've played with many settings and have tried to forward port 80 from the modem, but I've had no luck.
After replacing a Cisco CSS/SSL Accelorator and PIX firewall with an ACE 4710 to do load balancing and SSL encryption behind an ASA firewall we started seeing mangled HTTP requests in the Apache access logs for the servers in the server farm. This is occurring for several different URLs and not just the one above and for multiple web browsers.The ACE load balances to servers running Tomcat 7 with Apache HTTP server v. 2.2.14. A recent ACE software upgrade to A5(2.1) has not fixed the problem.
View 1 Replies View Relatedi am facing the same problem now but am using windows 2003 server
View 1 Replies View RelatedI have install the administration toolpack on Windows 7 and enabled remote connections on my server 2008 box, When i try and connect with my Windows 7 server manager it does not work.I see stuff on google about enabling a trustedhost with winrm but can't find a way to do this.
View 18 Replies View RelatedIs there an iTunes Server for WHS 2011 available?
View 3 Replies View RelatedAfter getting New Workstations, I wanted to connect that to the SERVER but Windows 7 could not log into domain of our server with Windows Server 2003. Besides following the proper process/steps. I am able to use the printer and internet shared through SERVER though.
View 2 Replies View RelatedI've been reading that the Windows Server Backup that is included with Server 08 R2 is pretty good. Is spending $400 on a third party utility worth it?
I'm asking because we're purchasing a new server soon and I want to know if the included backup is going to be good enough. Will be backing up server state as well as data to tape and possibly an off site server (server 2003) if I get my way.
I know the best thing one should do is install an ISA server and an Active Directory Domain Controller on separate servers. But for some reason, I want to configure my Windows Server 2003 as an ISA server as well as an Active Directory Domain Controller. What can happen to my server making it run improperly. For example, my ISA server will function mainly as a Firewall, I wonder if all the rules I create in ISA server determine what I mean it should work or I have to consider any affection from Active Directory DC to those rules?I have to ask this question because I've already installed both ISA and AD DC on my Windows Server 2003, already created an Allow. All rule (just for testing connection) in ISA server but I can't ping from all the clients to my server, all the clients can ping each other and the server itself can ping to all clients. I just think that may be the affection from AD DC to my AllowAll rule in ISA server.
I successfully created some rules that worked greatly as they should work but when I hadn't installed AD DC yet (just installed ISA), however right after installing AD DC, it still worked well (this made me think that AD DC didn't affect to how ISA works). Then I configured a little related to DNS server, and maybe something I don't remember exactly and now I can't ping from my client PC to my server. My network is virtualized using VMware 8 workstation and GNS3, at first there is no need of GNS3 because I just want to test my internal network (some clients connected to the internal interface of ISA server). Depending on VMware that I can't be sure if it is some fault of VMware or any other thing but my configuration on the servers.
How would I set up my own anonymous proxy server with my own ip address without having to go on a proxy list site? I don't care how complicated or time consuming it may be, I'm a very fast learner and I do things extremely quickly.
View 3 Replies View RelatedI host a minecraft server for my friends, but I always have to give them my ip every time because my ip changes everyday, and that is really annoying.
View 11 Replies View Relatedi need a guide to set up a server network.
View 1 Replies View RelatedI've made hotspot ad hoc and then my client try to connect my hotspot but it must setting manually...how to my client connect to my hotspot automatically not manually??? and how to install and setup dhcp server i windows 7...
View 6 Replies View Relatedshow me the necessary steps and a type of hardware/software to buy to setup a network storage server that allows me and my family to access/share all files from anywhere thru the internet?
View 5 Replies View RelatedAbout my internet setup, I receive internet from my ISP via the LAN cable. The IP is static, provided by the ISP. To use the internet, I have to login to their server using a username and password.Earlier, I did not have a router. So, to see if the ISP server was up, I could just ping the IP of the ISP server from my computer using the command prompt, and it would show whether it was up.However, since I got a router, I find that I cannot ping the ISP server from the computer directly as before. To ping the ISP server, I have to open the router administration page using the browser, then use its diagnostics feature to ping the ISP server. It shows only a few pings, and is not like the continuous ping that can be seen when you run ping from the command prompt. So, it's difficult to see the pings, and also diagnose. Also, sometimes the router pages do not open and get stuck, even after being refreshed.Is there any way, or any setting, by which I can ping the ISP server from the command prompt on the computer? Do I have to make changes in firewall settings of computer, or any settings in the router?Why can't I ping the ISP server directly from the computer?I am using Windows 8. The firewall of Windows 8 is on, and the hardware firewall on the router is off.
View 9 Replies View RelatedHow i should setup my network to include a DNS Server. I have 2008R2 running on a VM on my main desktop machine (this will soon be moved to a dedicated VM Server) with my Virgin Superhub acting as the primary router / modem. I also have a Belkin N+ router in AP mode and a dedicated AP for wireless around the home.I have a few options on how to configure the network adaptor for the VM Server. [code] On my host machine i have the two default VM Network adaptors for "Host only" and "NAT".Im not really sure on how the IPv4 should be configured on these adaptors in order than the VM server is on the same network as my physical machine without conflicting IP's. If i leave it default the VM server gets a default IP of 192.168.13.138.
View 1 Replies View RelatedI've setup a NTP service by using Cisco 2811 routers. This works fine at the moment, but in the end there are some questions left.
1. I'm using two 2811 Routers, one for primary, which is resceiving the time from PUBLIC NTP 1, and one for backup, which is resceiving the time from PUBLIC NTP 2. Is it possible to compare these to times an check if the match? And if not, generate an alarm via e.g. SNMP
2. Is it possible to check via SNMP, if the routers are reaching PUBLIC NTP 1 and PUBLIC NTP 2 for sync?