Belkin F7D1301 / Baton IBLR6111A - NAT Capable Modem Linked For Failover
Jan 31, 2013
There are a total of 7 systems on the network. The network has evolved from two small shops (3-4 computers each) to a single one with a sum total of 7 systems. Historically there were two ISP (which the new management would like to continue). Thus there are two NAT enabled devices at the last-mile from each ISP
Belkin F7D1301
Baton iBLR6111A
Networking is almost an unknown to me. An ip config on the computers in the network brought the realization there are 2 sub-nets ... at least it looks like there are 2 sub-nets (192.168.1.x, and 192.168.2.x).
My gut tells me the above mentioned modem/router cannot be connected & configured to be used transparently for the computers connected to the other modem/router without additional hardware. Is this right?
View 1 Replies
ADVERTISEMENT
Dec 16, 2012
I was told by my Internet company that my router may not be compatible with my new modem (from them). I have a Basic Wireless Router. Model f7d1301. Purchased about 1 year ago. I was told that Belkin designs it this way so we have to buy a new one regularly. But 1 year!!! That is terrible. Is it true? Is this older router no good? I have purchased a new one and it seems to,have solved the problem. It does take me very happy that I already have to buy a new one....
View 1 Replies
View Related
Apr 26, 2013
How do I setup my Belkin F7D1301 with a 16 port 10/100 switch so I can use the wireless on the Belkin and have the 16 port switch for my hard wires?
View 1 Replies
View Related
Apr 13, 2013
I have added a list of Mac numbers for allowed devices & checked the enable mac filtering box,but did not check the block box.All the Mac number devices, cannot access the wifi.But if I uncheck the "enable mac filtering box"all the Mac number devices can access the wifi.This also include other devices not in the list can also access to the wifi.It seem that the router can only block mac number BUT cannot have "allow list"I checked my firmware = 1.00.22 (Aug31 2000 14.36.01)Is this the latest firmware??
View 6 Replies
View Related
Feb 21, 2013
I have added a list of Mac numbers for allowed devices & checked the enable mac filtering box, but did not check the block box.
All the Mac number devices, cannot access the wifi. But if I uncheck the "enable mac filtering box" all the Mac number devices can access the wifi.
This also include other devices not in the list can also access to the wifi. It seem that the router can only block mac number BUT cannot have "allow list"
I checked my firmware = 1.00.22 (Aug31 2000 14.36.01) Is this the latest firmware?
View 3 Replies
View Related
Jun 1, 2012
My Belkin Wifi router which was working fine earlier has stopped working now. It shows a red/orange light and nothing else ( it normally shows a green light ). The light doesn't blink or flash. As a consequence, my wifi devices aren't connecting to the internet, however i can connect via my pc normally through my modem. I have a iball Baton modem and the model number of my wifi router is F7D1301 V1.
View 4 Replies
View Related
Oct 29, 2012
F7D1301 v1 is my router model. i installed it this morning; all was working fine; then i changed password; still working fine; then i attempted to change pw a second time; router turned to solid orange and no matter what i try, i can't get it working again. i reset it, unplugged it, etc.
View 5 Replies
View Related
Apr 7, 2011
i have beetel adsl2+router connected to my main computer through ethernet cable but its wifi signal is very low. its signal hardly reach the other end of my house where my bedroom is, and i want to surf on my laptop or mobile from my bedroom only so basically i want to extend my wifi range or boost the signal the thing is i have a belkin f7d1301 basic n150 wireless router, i want to know whether i can use it as range extender or any other thing to boost my signal.
View 7 Replies
View Related
Jan 5, 2011
I recently linked my dtv receiver to the internet through my laptop. My question is, since I'm now sharing the connection, do I need to make any adjustments in the "network and sharing center" to keep sensitive info on my laptop safe?I do have Norton Internet Security.
View 1 Replies
View Related
Aug 18, 2011
I have a Netgear Router connected by DSL to the Internet (through Roadrunner). I have a AT & T Microcell Tower and 2 computers connected to the Router: a desktop running Windows XP Home Edition wired to the Router and a laptop running Windows 7 connected to the router wirelessly. Both computers connect to the Internet without any problem. However, they do not communicate with each other. The laptop indicates a home network with all 3 devices, but cannot communicate with the desktop. The desktop does not show any network at all. It only indicates a connection through the Router.
View 1 Replies
View Related
Sep 28, 2012
Question: how would STP or RSTP behave in a star topology with a hub in the middle?i.e. you have four switches all linked to the same central hub. Single links, no loops.Each switch would then get BPDUs from everybody.Going by theory, it should be OK since it still sees the root's BPDU and will see the link to the hub as the root port, despite presence of other BPDUs from other switches? No different from receiving an inferior BPDU from an upstream switch and a superior BPDU from a further upstream root switch.I guess I could lab it by turning off spanning tree on a switch to simulate a hub? I've never previously had to deal with STP issues where there are hubs that aren't strictly point to point bridging so to speak (ok they're not bridging but you get the drift).I've got a scenario I'm examining at the moment where this is the topology, except all switches have bpdufilter running hence effectively no spanning tree. I'm curious to know what would happen should I remove the bpdufilter.I realise there is zero benefit in spanning tree in this instance as I don't have any redundant loops to fall back on, but I'm reluctant to turn off STP on those vlans (since obviously theres stuff behind those switches). The BPDUfilter method seems like an elegant solution but I wonder if its actually necessary.(the hub is actually a VPLS mesh, most sites terminate PE to CE router but I'm playing around with switches as the termination points – run our own Q in Q, split vlans off before it gets to layer 3 as separation, etc.)
View 1 Replies
View Related
Aug 19, 2011
I'm just wondering why my computer is being associated twice before being secured and linked when it obtains an IP address from the DIR 655 router. I am using the DWA-552 wireless card to connect to it. When I first started using them together, this wasn't happening. Then, all of a sudden, one day it just started showing "above message repeated 1 times" just below the log entry for the client being associated".
View 5 Replies
View Related
Jun 21, 2012
I'm trying to use MRTG and SNMP on a Windows Serveur 2008R2.I want to manage my Switch with mrtg, but it don't show me which computers or server are connected to the Switch's ports.All I have, in the .cfg file is the interface name ( like S0/0 ), which are useless for me, I would like to get IP adresses or hostname but mrtg doesn't seems to do it.Any of you know if Mrtg can do that ? or maybe there are some others ways to do that ?
View 1 Replies
View Related
Jun 1, 2012
I am trying to set up a new Belkin modem/router.I have Internet on all three computers over both ethernet and wireless, but no local network. I think the problem may be IP addresses, but I cannot solve it.The LAN settings in the router now are:
DHCP (.) On
IP Pooling Start 192.168.2.2
IP Pooling End 192.168.2.100
Lease time: forever
LAN/DHCP Client List is empty.With the previous modem the IP addresses of the machines were from 192.168.1.2 upwards, but the new modem considers this range invalid.(This isn't specifically an XP problem as one of the machines is Window-7).
View 19 Replies
View Related
Jan 5, 2011
My DIR-655:
Hardware Version: A4
Product Page: DIR-655
The problem is that Website Filer doesn't work if on STEP 3: SELECT MACHINE of Access Control the machine was selected by MAC address. When the machine was selected by IP everything is fine.The problem is that IP addresses are assigned dynamically, so how to make sure that the policy would be applied to the same machine?
View 8 Replies
View Related
Aug 29, 2011
I know there are a lot of threads out there regarding connection issues, both with wireless & LAN connections, after updating firmware to 1.35. To provide a snapshot of my setup...I have 3 GB switches throughout my home, a couple Ethernet enabled Blu-Ray players, 2 XBOX 360's, multiple satellite receivers with Ethernet, 5 PC's, 3 iphones, etc...you get the picture. I also have 5 older DLink wi-fi cameras. So, with this said my setup has been flawless for some time. However, a week or so ago I upgraded my firmware on my DIR-655 to the latest version...everything still seemed fine at the time. Yesterday I noticed we had no wireless internet so I went and checked. Sure enough...no connectivity on my desktop that's directly linked to the router, etc.
I tried rebooting & then resetting the router...got connectivity, but as soon as I plugged my PC into the switch...no IP address. I played around with settings, wiring configurations, etc...I'm pretty up to speed on this setup so I felt I exhausted every option. I thought my router went bad...gave me an excuse to go get the latest so I brought home a NetGear N750...hooked it up. As soon as I changed the LAN IP address range to condense the #of IP addresses I'm giving out again, the LAN connection to the PC was lost...I could not get it restored. I finally got it working, bypassing the GB switch, but the wireless would lose connection literally after a few seconds.
I ended up taking the NetGear router back and bought the exact same DIR-655, but this time it was HW version B1 instead of A and it was firmware #2.00 or something like that. I hooked it up when I got home...configured the system to exactly the way I had it before and PRESTO!!! My system is working like it was before. I can only think that the firmware upgrade I made on the previous router screwed something up in my system.
View 4 Replies
View Related
Aug 6, 2011
In my home I have a cable modem wired to a links wireless router a wrt 300n in my office (only hardwired used in there) and I do not get such good distance to my back bedrooms with my laptop. I have run a Ethernet cable dead center of the house for my sat receiver that is connected and wired to the 300wrt. Here is my question can I use the 150 like a hub or switch at the office connected to the cable modem and use the wrt300n router so that I get wireless on that side of the house. Or in reading here I see I can maybe use a bridge. I do have a older Linksys wrt150n sitting in a box.I have read until my eyes are almost bleeding and am not sure. How I can get a better signal on the other side of the house.
View 4 Replies
View Related
Feb 17, 2012
My desktop computer hangs when i use internet linked software like Mozilla and internet explorer. When i got hang i can't do anything but to press the restart on my CPU. But i can access only in Yahoo messenger and skype. It's really weird, I've been using it for a long time but i just only encountered it now. I tried to use my computer in safe mode with networking and it all worked! but why isn't it working in my normal mode. it's so hard
View 1 Replies
View Related
Dec 23, 2011
Currently I'm using BT Broadband with a Cat 5 Ethernet cable.My laptop has a gigabit Ethernet port, and I have the cable plugged in.Is there a way to determine whether or not the cable is capable of 1000Mbit/s, as I am receiving 100Mbit/s, when I check the connection.Also, will replacing the cable with a new one achieve the full 1Gbit/s?
View 14 Replies
View Related
Oct 11, 2012
My main networking device is the Ericsson T073G HGU ONT, and when I am connecting to the network through the Ethernet there are no problems. However when I connect my Belkin F6D4230-4 router to it (through cable) my router cannot recognize the modem.
View 18 Replies
View Related
Aug 6, 2012
Last week, a big storm rolled through my town while I was out of the area on business. I had a working LAN/WLAN for my home & home office, and the modem I was using got fried by the storm. Strangely enough nothing else was affected..Anyway, I went out and bought an identical modem, and had it set up with Comcast. If I connect directly to the modem, everything works perfectly. But when I try to attach my router to the new modem, I have no connectivity over wifi OR hardwired to the router. According to the status light on the router, it can't find a connected modem.I reset the router back to factory settings, installed the newest firmware, and moved my DHCP pool out of the default range. I then power cycled the whole setup - twice - with no success.
View 5 Replies
View Related
Apr 10, 2013
I recently had trouble with my Comcast Xfinity internet service and called to have them send a refresh signal. I was up and running again with my ethernet, but my wireless service using a Belkin N150 wireless router hasn't worked.From everything I had read I needed to do a hard reset of the Belkin N150 router and then reconfigure it's settings. Well I did the hard reset and power cycled everything, the modem, computer and router. I then plugged in everything again and connected the modem to the WAN on the router with one cable, and the computer to the LAN on the router with another cable. (I am using a Macbook Pro operating with Mac OSX). Now I cannot connect to the url...to configure the settings on the router at all!
I think the problem has something to do with my IP address. I opened the network settings and saw that my IP address is 50.138.25.x while my Subnet Mask is 255.255.254.0 and the router is being listed as 50.138.24.x. How to change this IP address to get my router connected or could it be another problem?
View 8 Replies
View Related
Sep 8, 2012
We have owned a this router for nearly a year now, and recently it has been acting up.Today I added a static connection or something of the like for my Xbox, with the correct ip gateway and subnet mask. Since the restart it has never stopped cycling the boot sequence without end. The download lights cycle and the router light flashes constantly. And I am unable to connect to the router page at 192.168.2.1 So I cannot reset the router, the hardware reset button just momentarily pauses the endless booting process.
View 4 Replies
View Related
Nov 27, 2012
My roommate and I have High speed cable internet and the modem is set up in his room. I bought a n600 belkin router and a usb wireless adapter so my computer in my room will get internet. Only problem is there is only one ethernet port on the modem that the internet provider gave us and of course that is taken up by his computer. How do I hook up the router to the modem and get all this to work so I can get on the internet as soon as possible?
View 1 Replies
View Related
Jan 6, 2011
I have a DSL model from AT&T that gives me 4 ports and I have a Belkin Wireless router that gives me another 4 ports. BUT, the computers on the AT&T modem cannot see the computers on the Belkin router. Should I set the address in the Belkin router to the one the AT&T modem has?
View 7 Replies
View Related
Jan 18, 2013
I have a Belkin N450BD that doesn't seem to want to connect with my Siemens modem. The WLAN cable is connected to the WLAN port on my router but the WLAN light on the modem doesn't illuminate.
View 1 Replies
View Related
Feb 12, 2013
Can I set-up the N300 wireless router without a modem, this I want to use for wireless printer connections only for several PCs
View 2 Replies
View Related
Nov 24, 2012
I reset the f5d9321 router and no connection with modem, power cycled the modem and router and still no connection with the modem. Pc and laptop can connect to internet by connecting to modem. The router worked fine 3 days earlier.
View 1 Replies
View Related
Jan 24, 2013
How do I hook up a Belkin 750 Router to my modem when modem has only one plug?
View 1 Replies
View Related
Dec 7, 2011
I am trying to get a C2960-8tc-L linked to a sge2000p via the Gbic ports using GLC-SX_MM gbics but having no luck.Are these compatible and should I need to configure anything?
View 1 Replies
View Related
Oct 31, 2011
Is there any easy way to tell what networking level my laptop is capable of? Its an older IBM, T30.Wireless works fine but I'm thinking of upgrading the router and want to make sure the laptop will connect using the faster N network speed.
View 5 Replies
View Related
Oct 16, 2012
I run an Allen & Heath digital mixer. The iDr32 mixrack sits on the stage and has a 2 port Ethernet switch on board, which allows the device to be controlled with a PC. If you then add a WiFi router then you can have wireless remote control from a laptop. Allen & Heath also sell an app for iPad to do the same. I have this working quite well although I am receiving no metering data from the Mixrack. Allen & Heath say this is probably because my router does not support multicasting. They list some routers which are recommended, but the list is rather out of date. I am trying to find a suitable dual band router with decent range on both bands. I would prefer a cable type, but since it will not be connected to the internet, it isn't important. When I Google "Multicast capable wifi router" all that comes up is a lot of stuff about video streaming. None of the manufacturers seem to list if their product supports multicasting. I understand that multicasting is usually used for video streaming, but in my case it seems to be a requirement to speed up data between the iPad and the Mixrack. Apparently some users of similar systems have encountered problems with multiple smartphone users in the audience seeking WiFi connections. The solution to this is to use 5GHz band, and switch off the SSID. Some have also found it best to use MAC filtering for security.
View 4 Replies
View Related
Aug 24, 2011
I have a 1841 Router running C1841-ADVIPSERVICESK9-M ver 12.4(12), is this IOS VPN capable, if not what IOS would I need to run a VPN?
View 2 Replies
View Related
