10.6.5 Application Master To Accept Incoming Network Connections?
Jan 15, 2011In OS X 10.6.5, the following dialogue popped up:.Do you want the application "master" to accept incoming network connections?
View 3 RepliesIn OS X 10.6.5, the following dialogue popped up:.Do you want the application "master" to accept incoming network connections?
View 3 RepliesI have a standard ADSL modem which connects to the internet. On the inside I have a few computers within my LAN.when the modem receives an incoming request from the internet for a connection to one of my LAN computers e.g. a Skype incoming call, how does the modem know which port to forward that traffic to on my internal LAN? i.e. how does the modem know which of my computers is running the skype application that will answer the incoming call? I know port forwarding normally handles this sort of thing, but in my case, I am not using any configured port forwarding rules so how does the modem know where to forward skype traffic?
View 2 Replies View RelatedI am currently running a 2821 to terminate vpn links from all our branch offices over a WAN. I need to add a second interface in order to facilitate a move to a different WAN provider. seeing as the 2800 models are EOL I was looking for an upgrade. My local retailer wants to sell me the following:CISCO3925E-SEC/K9 IS Router 3925E security bundle SEC license pack,HWIC-2T 2 port serial WAN card,MEM-3900-1GU2GB Upgrade to 2GB 1,now my question is why can't i use the 2900 models in order to save some money?All I need is a router that will accept 2 different incoming WANs and the ability to create vpn tunnels over them..
View 19 Replies View RelatedI am going to install two new Cisco Prime LMS 4.1 servers application in a Master and Slave Deployment, and how many bandwidth is consumed between the servers.
View 1 Replies View Relatedi have with my Edimax router. I could not make any progress with Edimax personnel in Taipei.
If i connect my vista box directly w/o the router, i can see that port 21 (Filezilla) is open, using WhatsMyIP.org | Port Scanners/Sniffers
When I insert the Edimax br6215srg router, the port is in timeout as reported by aforementioned site (guess the port scanner gets no synack nor reset back to the syn it sends)
The router is set to "disable firewall" or to "enable firewall and DMZ enabled" with as client's ip the one that is configured in the router's dhcp table for the vista box. The NAT module is set to forward port 21 to the same ip. ipconfig confirms that i do get the ip programmed in the router's dhcp table.
I do not want to believe that this edimax box is unable to forward connections!
I recently moved house to a flat where I now have an adsl wireless router. Ever since I installed it its been major problems for me, my speeds are terrible takes ages to load a webpage and days to download anything. Also I have tried to stream to my apple tv through the use of airplay mirroring but this again doesn't work and an error code appears every time which I then looked up and it says its to do with my firewall blocking incoming connections. I have gone to my routers settings to try change this and it says to select the options by clicking the radio buttons however they do not exist on the page as you can see on the screenshot below.
View 1 Replies View Relatedwhich product has the capability to receive multiple incoming connections
View 1 Replies View RelatedI've been fighting with getting VPN connections working properly with my Dlink router. I set up virtual servers for PPTP and L2TP and could usually get the first attempt to work. Subsequent client connections would always fail.The logs display the following-Dropped GRE packet from 192.168.0.10 to 64.232.xxx.xxx as unable handle packet header. Blocked incoming GRE packet from 64.232.xxx.xxx to 76.105.xxx.xxx.What seemed to fix it was going to Firewall Settings and setting UDP Endpoint Filtering to Endpoint Independent and TCP Endpoint Filtering to Address Restricted.
View 1 Replies View RelatedHow to configure my DIR-615 (Hardware Version E1 - Firmware Version 5.00NA) to:
1. Assign/Reserve IP address for 2 machines.
2. Route a web browser to a server on the first machine (port 80) as a default when another computer or smart-phone or device joins my open wireless network.
I am hoping to eliminate any changes to the IP address of the first two computers so that the server's IP address and port are static. I would also like anyone who joins the network to merely open their browser and be presented with the http interface from my server.
I am trying to make my computer support incoming VPN connections. I am using Windows 7 Home Premium on the computer I want to make the connection on.I am also using Verizon FioS internet (comes with default router/modem combo) to which I have the DIR-655 router connected. I am able to connect to both WiFi's fine and they work correctly.I think the Verizon router is set to block incoming VPN connections and I think this is why I cannot get anyone to be able to access my computer / internet via VPN. How I can perhaps forward ports and which settings I would need to specifically change in both routers admin settings so that I can get VPN connections to forward to my computer and be accepted.
View 1 Replies View RelatedI need to block 4000 nodes (Ultrasurf, TOR exit nodes) and I've written a script that will ssh and copy in these objects (prob 100 at a time) into an object group and then put a blanket deny. I don't see a flood of traffic (occassional hits every other day, etc) but I was wondering what the impact would be? Can the ASA handle an object group of that size plus an ACL with it? Any way to block incoming connections from TOR/Ultrasurf?
View 1 Replies View RelatedI have a Cisco 3745 that is my internet router, I have a domain that directs the web address to the WAN IP address...Can I set up my 3745 to forward incoming connections to my server?
View 3 Replies View RelatedI am having an issue with the mentioned AP, it does not accept new user connections, however new user can connect after the AP is restarted.I would like to know if there is a limit on the number of wifi users for linksys x2000?
View 1 Replies View RelatedWe have a Cisco 2911 Router and have configured via BT Infinity Broadband for out going internet access etc. Are there any incoming restrictions ACL settings etc. that will stop us using for ISA VPN, Exchange connections, Intranet, Sharepoint etc. We have reserved 13 Static IP Addresses from the ISP.
View 1 Replies View RelatedI was at my computer when the desktop appearance and taskbar changed. I immediately opened task manager to see what program might have caused this and didn't see anything out of the ordinary. Then about 2 minutes later my desktop changed back to what it normally is. I then went and disabled remote desktop connections... I think that someone may have accessed my pc remotely, buy I wasn't able to catch them at it. Is there any way to review incoming remote desktop connections historically?
View 3 Replies View RelatedI've been fighting with my E2500 since I got it back in June with lag, dropped connections, etc. It's a bit intermittent but can hang around for hours at a time when it kicks in. Restarts but the issue always comes back. Most noticeable while gaming online or on a VOIP program such as Team Speak. Generally when it happens If I'm monitoring my Team Speak connection the incoming packet loss shoots up between 20-30%, starting to drop out every other word or so. No out going packet loss. The connection drops are random between computers (I have one mac and one pc in the house) where one will be fine and the other wont, or when the whole system will stay connected and drop all transfer. In the case of this last one it's not my ISP's connection as any streaming happening between one computer and an Apple TV device will also cease. I've also swapped back to my old router (an older model linksys) and all problems have stopped. Fully rebooted and reconfigured the router about 3 or 4 times and am on the latest version of firmware (1.0.003). It was much worse on 1.0.002 but still very noticeable on 003. Also no difference with a different wireless adapter. I've tried the chat technical support but all they did was take 45 minutes to tell me how to reboot my router after telling them I already had.
View 1 Replies View RelatedI was looking to setup a y configuration of routers with a modem going to master router, then from the mater router LAN ports to two other routers wan ports to give a guest and private network. I understand that this will all work fine for normal web surfing but can be very long winded when setting up port forwarding which i would need on the private network so I was wondering if I could get around this by setting up a DMZ on the master router for the private network router allowing all the port forwarding to be taken care of by just the one router. Would this work and would the two networks still be secure from one another.
View 8 Replies View RelatedWe have recently transitioned one of our Ecommerce products to a new data center, at which we now use a one-armed load balancing approach rather then the routed load balancing approach we used previously. This is casuing us some issues as we generally log the source IP address a user comes in on when he fills out an application. Now the logs only show the natted ip address recieved by the load balancer, which does us no good. Any way to log the source IP address when a new connection is created to a particular vip?
View 3 Replies View RelatedIs this normal to have millions of current connections within an ace 4710? There is only 3 current connections but shows a high number?
View 3 Replies View RelatedI have a little problem...I want to see the maximum tcp connections that I had on my Cisco. I tried using show ip statistics but it's not working. I have a Cisco Catalyst 3750G (WS-C3750G-48TS)
IOS -> Version 12.2(52)SE, RELEASE SOFTWARE (fc3)
Both the integrated wireless adapter in my PC and a USB adapter work fine and conect automatically to my D-Link DIR-615 router. I have the integrated adapter disabled in the control panel. Just bought a D-Link DWA-140 Rangebooster N wireless adapter. This finds all the networks my older USN adapter finds but at greater strength. When I click on connect to my own network I get the enter network key box. I enter the correct key, but get an error message telling it's incorrect. I revert to the older adapter or enable the integrated adapter and I get connected automatically.
View 5 Replies View RelatedACE A2(3.4). Is it possible to set a rate-limit connections per sec from any source IP. For example, if a client is trying to GET a web page 10 time per sec I will send a reset or drop that connection.
View 1 Replies View RelatedI have a problem with that the ACE20 (A2(3.2)) does send the connections to a backup real server in the serverfarm. I will how to troubleshoot in this case ? This is serverfarm configuration.
serverfarm host fix-http
failaction purge
probe PROBE-TCP-80
rserver fix11
inservice standby
rserver fix12
I have four ACE 4710. Each pair of ACE is in one geographical location. Probes are configured so that it is checking regular regex (HTTP GET).When there is need rserver update we change text in our testpage.html (for ie. from "OK" to "SUSPEND" ) so that probe detect fail. In fact rservers are still operational, but should not accept new connections. This works fine. BUT I observed that established connection/sessions did not end up after probe fails. ACE probably wait for openned/established connections to end up and it is what I am askign for.What happens if probe fails but in fact rserver is operational? I thought that if probe fails it also end up/cut all established connections to rserver. But seems it is not true.
View 2 Replies View RelatedWe are using a sticky serverfarm with 2 real servers, one server was down for maintenance for an extended period of time. When it came inservice again it was not getting any connections. is it because all the connections had stuck to the other server ? we want sessions to be sticky but we also want to LB?I got it working by bouncing the server that had been online all the time. things started to LB then.BTW the ACE 4710 is running 4.2.1
View 1 Replies View RelatedI must redirect all connections from port 443 to 9443.
this is configered and running:
serverfarm host FARM-002
probe test-xml
rserver svx-xmlfw-lb-01 9443
backup-rserver svx-xmlfw-lb-02 9443
inservice
rserver svx-xmlfw-lb-02 9443
[code]....
I have in the moment following problem. All connections become redirectet to port 9443 but port 8080 shouldn`t be redirectet to port 9443. What can i change in my config to solve this problem?
I'm trying to connect my printer to my wireless network via my new Netgear Gateway 7550. The printer will not accept the Wireless Network Key for the router.Had no problem with the old 2Wire gateway.
View 1 Replies View RelatedWe are using a ACE 4710 with A3(2.6) software release.I had to change our sticky load balancing method for HTTPS to cookie based.However while connections appear to work if I look at the show sticky database table I can not see or confirm sticky entries for the cookie based connections.Here or config snippets to show the config
sticky http-cookie ghh-www scook-ghh
cookie insert browser-expire
serverfarm ghh-www-443
class-map match-all ghh-www-443_CLASS
2 match virtual-address 172.16.1.21 tcp eq https
[code].....
I have a problem in the ACE 4710. In view of the connections of a web environment. When I view connections on Config> Operations> Real Servers, Conns column values appear very high connections (Example. 1606317769078).Already in Config> Operations> Virtual Server the number of connections appear normal. Version 4710 ACE Device manger A4 (2.1a)
View 1 Replies View RelatedI'm having a problem connecting with wireless card model number f9L1101v1 to a router model number F5D7234-4. the computer is dell dimensions 4400 desktop pc running windows xp, everything seems to be working correctly. i can see my wireless connection, signal strength is full, but when i enter the network key which i have confirmed is correct it will not connect. it goes to the window where it shows it trying to connect but after about 2 minutes the window disappears with no explanation for connection failure.the network key was confirmed through a laptop that runs on the same router.
View 2 Replies View RelatedI am trying to connect a steaming device to my wireless network but it will not accept the password
View 1 Replies View RelatedI have a D-Link DGL-4500 router and my landlord recently ungraded our internet connection. However, now I get this error message when I try to hook it up to the ethernet hub,"The addressing of the Internet side learnt thru DHCP conflicts with the addressing selected for the LAN side. Internet communications will be disabled until you have changed the LAN side addressing to resolve the problem."
View 3 Replies View Relatedi'm trying to download some poker software, in order to do this i'm supposed to grab small file from www and it has to connect with master server, get rest of the file and install it. on every platform i tried (titanpoker, everest, poker770, unibet) there's a message saying: cannot connect to master download server. either you internet connection is not functioning or the master download server is busy. i have turned off my antivirus and firewall (also windows firewall). my connection is ok, roommates have installed software easily+when i moved to another place still couldn't connect. ports seems to be blocked?
View 2 Replies View Related