I have Time Warner[Road Runner] and an ARRIS TG862 router. I have tried cmd->ipconfig->and connected through the address shown[Default Gateway;192.168.0.1] and have tried an ipconfig/ flushdns -> /release ->renew as well to no avail. Is there anything I could do to access the page? P.S. This was all done through a Windows 7 desktop connected directly to the router through an Ethernet cable
View 5 RepliesToday I got a new modem brought from Insight my ISP.
Modem: Arris TG862
Router: Cisco Linksys E1200
What happened is I connected to the modem's configuration page and turned off dhcp for all of the options because I wanted my router to do this, but after doing this and saving my settings, I can no longer connect to the internet or the modem no matter what I try. I really don't want to call insight when they just brought the modem.
I just switched ISPs and received a new modem, unfortunately I can't seem to connect my laptop online with this. Everything else connects fine, but something is up with my computer, it connects fine wirelessly to the modem, it just doesn't have a proper internet connection.I'm running windows 7, the modem is an Arris TG862.
View 2 Replies View RelatedI have a wireless Netgear extender, and can not find set up page..Can't access own router configuration page
View 3 Replies View RelatedI have the issue of being unable to access my router configuration page. My standard gateway IP (83.226.48.1), does not work, resulting in "unable to connect". If I try with my IPv4-adress, it just comes out with a blank page (Mozilla Firefox and Internet Explorer).
View 17 Replies View RelatedI have the next config: PC -> Asus RT-N16 router (192.168.1.1) -> LinkSys WAG54G2 in bridge mode (192.168.0.1),How can I access to modem's config page from my PC ?
View 2 Replies View RelatedI have been using this router for 6 months without problems. However, it hasn't been working since yesterday morning. It receives power but the Internet led doesn't light up. The network leds are blinking faintly and rapidly. I can't access the configuration page from my browser. Is it dead or not?
View 9 Replies View RelatedCannot access configuration page for WAP11 Access
View 9 Replies View RelatedI cannot access the configuration page for wifi router... my wifi router is buffalo WHR-G300NI usually access the page via 192.168.11.1but since I have plugged the wire from the internet socket on the wall to LAN port rather than WAN port and disable the DHCP , I cannot access the configuration page and I cannot change these because the ISP told me to do in order to access the internetIs there any other way to access the configuration page?if there isn't, how can I access to the configuration page
View 1 Replies View RelatedI get disconnected from my ADSL2+ connection now and then and it is starting to irritate my a lot so I want to investigate the problem, but I can't access my modem config page. The modem is a Zhone 1511-A1 and the default ip is 192.168.1.1. I tried to reset the modem to isp configs and it did not work. When I ping my address it says "TTL expired in transit". I really don't know what to do next to get into this config[CODE]
View 6 Replies View RelatedI have been trying to configure some settings on my modem and to do so I must access it from it's ip (192.168.250.1). However, when I load that ip in my browser it does not connect.
My router has a private ip of 192.168.0.1 because of a Double NAT issue which I am trying to fix by going to the modem's configuration page. I am pretty sure that it is 192.168.250.1 because that is what my router ISP Gateway says, along with ipconfig in cmd when I directly connected to the modem from my computer.
By the way, I am currently connected through my D-Link 254 router which is connected to my WiMax modem.
My question is regarding gaining access to my Linksys wireless router configuration page. I recently turned my Linksys WRT54GL wireless router into an access point and since I have done so I am no longer able to access the configuration page for my router.
The problem that I am encountering is not one of connectivity, but rather entry. Prior to turning my wireless router into an access point I was able to connect to the router by means of my browser (192.168.1.1). I am still able to connect to the router, but whenever I type in a user name and password the router just simply does not recognize the information. I have tried resetting the router multiple times, but I am still denied access to my router despite having the correct user name and password. I have version 1.1 of the Linksys WRT54GL wireless router and have the latest firmware.
i need to get into the web page because i need to open my XBL nat and when i type in the password to get into the routers page i get a blank screen
View 2 Replies View RelatedMy internet connection is fine but I really need to update the firmware on my wireless adapter. I have no problem accessing the router's config page. I ran ipconfig to get the adapter IP (screenshot attached/192.168.2.104). When I type the IP into the browser I get the "cannot display webpage" msg. I have tried turning off the power to the router, disabling Norton's firewall (I disabled Norton completely), and nothing works. Do not tell me to restore factory defaults on the adapter because I tried to get to the configuration page of another wireless adapter I have and am having the same problem.
View 7 Replies View RelatedI have a D-Link dsl 2640u, it's a modem but since it has 4 ports im assuming it's also a router. My problem is that when i enter my ip address into the address bar it doesn't recognize it. I can't use Utorrent or anything that requires ports to be opened..and it's a pain in the butt. when I type ipconfig on my command prompt it brings up..172.16.X.X and when i enter it into the address bar nothing is found. I'd like to port forward by accessing the modem's config page.I read on another thread that i could set my own ip address by going to: Control Panel>Network and Sharing center> Local Area Network>Properties of Ipv6 and typing my own ip address but when i do this i lose my internet connection.
View 14 Replies View RelatedMy router/modem is a DSL-2740BI created a hostname [URL] At my service provider I was able to create a DNS setting where I specified my routers IP address.In my router I think I created a port forward (TCP port 8080 on both external and internal) with the ip address of a small "web server" (an Arduino module for home automation).When I enter my hostname I get to see my router config page instead of my "Arduino page".
View 7 Replies View RelatedI have Verizon FIOS internet/wireless router and then a WRT310N wireless router connected to it thru Ethernet cable. I want to disable DHCP in the Linksys, but when I try to access the set up page at address 192.168.1.1 the Verizon router set up page shows up. I've tried to connect the router directly to the computer, but it needs the internet connection from the Verizon router. How do I get to the set up of the Linksys at the same time the Verizon is using the same address?
View 5 Replies View RelatedIt usually consists of installing routers in units. Occasionally I have to change the routers IP address to keep it from conflicting with other routers. To do so, I need to get to the router options to do that. Normally, typing in 192.168.0.1 gets me there with no problems. Sometimes it's a 10.0.10.1. (They have D-Link DIR-615 routers.) To make sure I know which address I need, I use the cmd and ipconfig /all. Some of the routers spit out an IPV6 address instead of the IPV4 that I need to access the router. Even after a factory reset, it still does this. I can't get in to change anything.
View 4 Replies View RelatedMoved into a new place, set up a connection. Server provider gives only one mac address, they set it on my router. They say that it should be working, make a restart and that's it. I did that but still no connection. Moreover, I cannot connect through the router at all and therefore cannot access router admin page to configure it either. Now what to do? Password for the router is correct. Even when I take down all the security, still I cannot connect.To be more specific, at first I could enter the router admin page, but since I didn't know how to configure it properly, I made some mistake. I think I choose setting "configure wireless network" and changed something there. After that I cannot access the admin page or connect through the router.
View 1 Replies View Relatedi need to do the following:
-go to routers startup page
-log in
-look for my WAN MAC address
it seems so easy, but i keep getting instruction to do things like type in different numbers into my browser which never work.
I am having a problem accessing my router settings page. everything was working fine and then all of a sudden my desktop couldn't get internet but all the laptops could so I tried everything power cycling the everything changing the Ethernet cable and I got nothing. So then I hard reset my router and erased all the settings and now it works so I have internet just fine and right away after I hard reset I could access my router settings page and input all of my settings like DNS servers and port forwarding and changing my SSID etc. but now every time I try and go to it it just won't I don't even get the login prompt nothing. So why I can't access this page. Here is a copy of my ipconfig /all. Also when I ping 192.168.0.1 I have no packet loss.
Edit:I have gotten it to work in IE I have to go to HTTPS://192.168.0.1 and then click go to site anyways after it gives me a warning about the certificate being invalid and I have to allow it or whatever otherwise it won't bring up the login prompt. Also the same thing is happening for FF so I need to go to https://192.168.0.1 and click I understand the risks and add exception for it to work.
Windows IP Configuration
Host Name . . . . . . . . . . . . : Andrew-PC
Primary Dns Suffix . . . . . . . :
Node Type . . . . . . . . . . . . : Hybrid
IP Routing Enabled. . . . . . . . : No
WINS Proxy Enabled. . . . . . . . : No
[code]....
I have a linksys router, Its at my sisters house. her son is trying to hook up his Xbox to it. The router will not allow me to access the router page, ( I called them and walked them through it). I reset the linksys router, by holding the reset button in for 45 seconds. Then I access the router page by going to 192.268.1.1 Windows gives me a popup to log in, What I find on the internet for a default login is the user name is blank and the password is admin. OR the both the user name and password is admin. However it still will not let me into the router page.
I am wondering if the login popup is something with the windows settings. As when I had the router here at my house, I think It just went to the webpage of the router and thats where it asked me for the user name and password. I do not recall the popup login window before the router page. Is there something to turn off to set it so that windows does not give a popup to login and goes to the webpage to login?
running linksys wrt54g wireless router to two towers and 1 laptop----had short power outage after which i lost connection to router only on one tower---other tower and laptop were unaffected----had green indicator lights for positions 1 and 2 hard wire connected towers before outage---now only position 2----looking for reasons why I lost number 1 and thus connectivity to the router----have tried powering down router etc---but have not reset it---looking for more info first
View 1 Replies View RelatedMy wifi router, Linksys WRT54G v3.1 has been working fine till now. Suddenly my laptop stopped receiving wifi signal. I am unable to access the set up page via 192.168.1.1 either from my laptop or from my desktop that is connected to the modem via the router. I reset the router as well but no luck.
View 5 Replies View RelatedI just got a new router and modem in 1:
300Mbps Wireless N ADSL2+ Modem Router (Annex B) TD-W8961NB I use a WIRED connection, not wireless.
When I type in the IP adress into my IE adress bar (192.168.1.1), it says it cannot connect to the internet.
I checked if all cables are correct alot of times, and reset it a ton of times, but no luck.
So I was having problems staying connected to the wifi on my samsung galaxy mini. Many fixes for other models in the galaxy series, limited fixes for the 'mini' version. Long story short, I was told to edit the DHCP lease time in my router settings.There I bumped into another problem.No mather what I tried there was no way of accessing the page. Weird thing is I remember having logged in on it before.Usually you just have to give in the standard gateway which should be 192.168.0.1 in my case. I checked it using ipconfig in cmd and my presumption was confirmed.Then I tried resetting the router to set back any settings that might've accidently been changed, in the hope that it would also reset the standard gateway and no succes.Now my knowledge about networking is verry limited.
View 8 Replies View Relatedi need to access my routers settings. i have my default gateway 192.168.21.254 . i enter that into my web browser, and it takes me to a user agreement page. the whole purpose of this is to set my NAT type to open on my xbox 360.
View 3 Replies View RelatedI was doing some changes in baitone router due to mistake i have disabled something in it.Now i am not able to access its admin page....Before it i was accessing through 192.168.1.1
View 3 Replies View RelatedI upgraded my router from version 1.2 to 1.35NA, through the Tools / Systems page on the router (uploaded the bin file). I am connected to the router via a wired connection.
During the upgrade, the message said I wouldn't be able to access the webpage until 75 secs. I watched it count down the seconds and then when it refreshed, I could not get to my routers page: 192.168.1.2
The DLink Router is connected as a pass through router to my FIOS router, so that I can use the wired ports and I use the DLink as my wireless router (fios router wireless strength was poor).
All the lights on the router are working as though everything is ok. I am still connected to the Internet, so it appears that the pass through of my wired ports is still working after the firmware upgrade, but wireless is not. Not surprising. I expect I may have to upload my settings (which I did save), but since I cannot get to the routers page, I feel a bit stuck.
two more bits of into. I also tried getting to 192.168.0.1, which might be the default? and I cannot get there either. My Fios router is on 192.168.1.1 (and as mentioned, the DLink should be at 192.168.1.2). Fios Router reports that the 192.168.1.2 port is inactive.
Whenever I enter 192.168.1.1 to access the login page of my router, I cant access it to configure it even after resetting it !I also tried changing TCP/IP settings to static as mentioned in the router's manual but it dint work?
View 4 Replies View RelatedUnable to access router admin page for Haier model R800
View 1 Replies View RelatedI want access the my E1200 website in order to implement new username and password to secure the network.
View 1 Replies View RelatedI need to access my modem config page which I could access months ago. In Start, Run, cmd, ipconfig, my default gateway is "192.168.1.1". when I type it in Chrome Browser it says Error 324(when antivirus on) and Error 101(when antivirus off). Tried with explorer (cant connect), Firefox(says done and a blank page) and opera, none working.The last time I could connect to that configuration page was like 4 months ago but I think I did something wrong and can't do it anymore.
View 19 Replies View Related