I get disconnected from my ADSL2+ connection now and then and it is starting to irritate my a lot so I want to investigate the problem, but I can't access my modem config page. The modem is a Zhone 1511-A1 and the default ip is 192.168.1.1. I tried to reset the modem to isp configs and it did not work. When I ping my address it says "TTL expired in transit". I really don't know what to do next to get into this config[CODE]
View 6 RepliesI have been trying to configure some settings on my modem and to do so I must access it from it's ip (192.168.250.1). However, when I load that ip in my browser it does not connect.
My router has a private ip of 192.168.0.1 because of a Double NAT issue which I am trying to fix by going to the modem's configuration page. I am pretty sure that it is 192.168.250.1 because that is what my router ISP Gateway says, along with ipconfig in cmd when I directly connected to the modem from my computer.
By the way, I am currently connected through my D-Link 254 router which is connected to my WiMax modem.
I have the next config: PC -> Asus RT-N16 router (192.168.1.1) -> LinkSys WAG54G2 in bridge mode (192.168.0.1),How can I access to modem's config page from my PC ?
View 2 Replies View RelatedI need to access my modem config page which I could access months ago. In Start, Run, cmd, ipconfig, my default gateway is "192.168.1.1". when I type it in Chrome Browser it says Error 324(when antivirus on) and Error 101(when antivirus off). Tried with explorer (cant connect), Firefox(says done and a blank page) and opera, none working.The last time I could connect to that configuration page was like 4 months ago but I think I did something wrong and can't do it anymore.
View 19 Replies View Relatedfirst off I was trying to change my ip address to dynamic from static, turns out I cant manually, anyways I was messing around with the configuration on my modem page (192.168.0.1) trying to enable dhcp because I know that if it shows that its not enabled yet I get my ip address automatically, it means my ip is static. I enabled a few things like netbios over tcpip and such and something to do with dns routing but I cant recall all I did and in what order because I can no longer get into the config. page and I cant connect to the internet and when I use command promp to renew my ip it says "an error occured while renewing interface local area connection... unable to contact your dhcp server and also an error occured while releasing interface loopback psuedo-interface1 : the system cannot find file specified.
View 2 Replies View RelatedCannot access configuration page for WAP11 Access
View 9 Replies View RelatedI cannot access the configuration page for wifi router... my wifi router is buffalo WHR-G300NI usually access the page via 192.168.11.1but since I have plugged the wire from the internet socket on the wall to LAN port rather than WAN port and disable the DHCP , I cannot access the configuration page and I cannot change these because the ISP told me to do in order to access the internetIs there any other way to access the configuration page?if there isn't, how can I access to the configuration page
View 1 Replies View RelatedI've tried all IP's that could be... 192.168.1.1 ,etc. , etc.Of course I am behind a router but even though I tried the same with connecting directly, it showed my gateway to be 78.56.191.254 which didn't work at all ( but was ping-able ).I restarted router and computer several times as well as switched form router to direct connection which brought no luck as well.
View 9 Replies View RelatedI have a wireless Netgear extender, and can not find set up page..Can't access own router configuration page
View 3 Replies View RelatedI have the issue of being unable to access my router configuration page. My standard gateway IP (83.226.48.1), does not work, resulting in "unable to connect". If I try with my IPv4-adress, it just comes out with a blank page (Mozilla Firefox and Internet Explorer).
View 17 Replies View RelatedI found out that I cant access my modem (TP-Link W8901G) config page at 192.168.1.1. I was pretty sure my ID and password is correct since I never changed them. It is also unlikely that the password got changed by other people who are stealing my Wi-Fi as I turned my WLAN on only when I requires the connection then it get turned off afterwards.
View 5 Replies View RelatedI have Time Warner[Road Runner] and an ARRIS TG862 router. I have tried cmd->ipconfig->and connected through the address shown[Default Gateway;192.168.0.1] and have tried an ipconfig/ flushdns -> /release ->renew as well to no avail. Is there anything I could do to access the page? P.S. This was all done through a Windows 7 desktop connected directly to the router through an Ethernet cable
View 5 Replies View RelatedMy question is regarding gaining access to my Linksys wireless router configuration page. I recently turned my Linksys WRT54GL wireless router into an access point and since I have done so I am no longer able to access the configuration page for my router.
The problem that I am encountering is not one of connectivity, but rather entry. Prior to turning my wireless router into an access point I was able to connect to the router by means of my browser (192.168.1.1). I am still able to connect to the router, but whenever I type in a user name and password the router just simply does not recognize the information. I have tried resetting the router multiple times, but I am still denied access to my router despite having the correct user name and password. I have version 1.1 of the Linksys WRT54GL wireless router and have the latest firmware.
I have been using this router for 6 months without problems. However, it hasn't been working since yesterday morning. It receives power but the Internet led doesn't light up. The network leds are blinking faintly and rapidly. I can't access the configuration page from my browser. Is it dead or not?
View 9 Replies View RelatedMy internet connection is fine but I really need to update the firmware on my wireless adapter. I have no problem accessing the router's config page. I ran ipconfig to get the adapter IP (screenshot attached/192.168.2.104). When I type the IP into the browser I get the "cannot display webpage" msg. I have tried turning off the power to the router, disabling Norton's firewall (I disabled Norton completely), and nothing works. Do not tell me to restore factory defaults on the adapter because I tried to get to the configuration page of another wireless adapter I have and am having the same problem.
View 7 Replies View RelatedI cannot access my Motorola SB6141 cable modem status page at 192.168.100.1 thru the EA6500 router. I can bypass the router and can connect to the status page with no problem. Is there a setting to change or can I possibly do port forwarding to access it?
View 9 Replies View Relatedi need to get into the web page because i need to open my XBL nat and when i type in the password to get into the routers page i get a blank screen
View 2 Replies View RelatedI've got the DIR-825 2.02. I had an issue where if you did change the IP adress default 192.168.0.xxx to something like 192.168.yyy.xxx, the configuration page was becoming inaccessible. It was super slow, was displaying the wrong pages with missing images and wrong page formating. I had to reset the router to default and then it was working fine.That seems to have been fixed since 2.05. Now you can change the default ip adress to anything you want and the configuration or setup still work fine.When I am on LAN, the setup page are displayed almost instantly. By remote, it's super slow.
View 1 Replies View RelatedI have a D-Link dsl 2640u, it's a modem but since it has 4 ports im assuming it's also a router. My problem is that when i enter my ip address into the address bar it doesn't recognize it. I can't use Utorrent or anything that requires ports to be opened..and it's a pain in the butt. when I type ipconfig on my command prompt it brings up..172.16.X.X and when i enter it into the address bar nothing is found. I'd like to port forward by accessing the modem's config page.I read on another thread that i could set my own ip address by going to: Control Panel>Network and Sharing center> Local Area Network>Properties of Ipv6 and typing my own ip address but when i do this i lose my internet connection.
View 14 Replies View RelatedMy router/modem is a DSL-2740BI created a hostname [URL] At my service provider I was able to create a DNS setting where I specified my routers IP address.In my router I think I created a port forward (TCP port 8080 on both external and internal) with the ip address of a small "web server" (an Arduino module for home automation).When I enter my hostname I get to see my router config page instead of my "Arduino page".
View 7 Replies View RelatedLinksys tried multiple WRT54g routers and access point, 192.168.1.1 can't open the router config page.
View 5 Replies View RelatedI bought this wireless router the other day in order to get internet access on my Nintendo Wii. I set it up using the CD and followed all the instructions (made a password, wrote down the key, etc.) - and my Wii CAN detect it, but when I type in the key on the Wii I get an error message. I looked online and they said the way to fix that specific error is to "change the channel" on the router to 1 or 11. (It is currently 6). I type in my IP into the browser like I'm supposed to (the default IP of the router), but ALL the options on the page are greyed out and nothing is click-able. Here's a screenshot
View 3 Replies View RelatedI'm currently trying to setup a Linksys SRW2048 switch.
The switch came with version 1.0.0 of the firmware (circa 2005), which worked fine with Google Chrome and Safari on OSX.
However, I recently upgraded to 1.2.2 (circa 2009), and the in-built web configuration page doesn't seem to work in anything except for IE6 or IE7.
Chrome and Safari give me a whole bunch of resource not available errors, and the page itself doesn't render properly at all:
Firefox also doesn't render it properly either:
It seems a bit strange on Linksys/Cisco's part that they'd release an updated firmware that meant their switch could only be used by Internet Explorer.
Or failing that, are there any known workarounds to get this to work with Chrome, Safari, Firefox - anything other than IE? Or anything on OSX or Linux?
Also, I heard that firmware 1.2.1 still works on non-IE browsers - any archives of older Linksys switch firmwares?
I have a D-Link DSL-2520u ADSL2+ modem. When I access the page 192.168.1.1, it prompts for a username and password. Upon successful authentication, I see the modem configuration page.
If I am on a different network, I can also access the modems configuration via its public IP address.How can I restrict access to the configuration page via the public IP address and only allow access via the internal IP address?
I have ZTE ZXDSL831II modem. Here is the [URL]how can I block a website from modem configuration page?
View 5 Replies View RelatedOnce in a while, I lose Internet connection and at the same time cannot reach my Siemens Speetstream 4100b DSL modem's setup page 192.168.0.1 ; it happened again this morning (from both wired and wirelessy connected computers). When I go to the router's setup page 192.168.1.1 , it would usually in that situation show that the router has not acquired the Internet IP Address; I power-recycle (a few times) both modem and router and eventually the router reports that it has acquired the Internet IP Address, but there is still no Internet, and the DSL modem's setup page 192.168.0.1 is unreacheable.The situation usually self-resolves only in an hour or so after the time the router has acquired the Internet IP Address: Internet starts working, and the DSL modem's setup page 192.168.0.1 becomes reacheable.
View 2 Replies View RelatedRegion : Others
Model : TL-WR841N
Hardware Version : V7.2
Firmware Version : TL-WR841N_v7_120201
ISP :
I recently encountered a problem with my router. It's configuration page is not accessible quickly. When I opened it ( by typing 192.168.1.1 in my browser) it took ages to open and even when it did, the page lacked a lot of features i.e., it did not load properly. Then on a suggestion by a friend, I downloaded the latest correct version (I have an IQ above 60) for my router but the problem persisted. And it is only on my PC. When I access it from some other PC, it opens as it should. My router is only 6 months old.
if it is possible to access a modem setup page with a E4200 router? My router is on 192.168.254.200 and modem(WAG-200G) is on 192.168.254.100, ethernet cable is on internet port on the e4200 and on port1 on the modem. Modem is set is bridge and I set up a ppoe and dhcp on router. Everything is ok, except that i can not access modem setup page to see adsl conection speed and settings.
View 1 Replies View RelatedI have Verizon FIOS internet/wireless router and then a WRT310N wireless router connected to it thru Ethernet cable. I want to disable DHCP in the Linksys, but when I try to access the set up page at address 192.168.1.1 the Verizon router set up page shows up. I've tried to connect the router directly to the computer, but it needs the internet connection from the Verizon router. How do I get to the set up of the Linksys at the same time the Verizon is using the same address?
View 5 Replies View RelatedI'm moving from an 1801W to an SRP547.My adsl supplier (BT) has given me a username and password, and also a router IP address, a subnet and an gateway IP address. I have 13 fixed IP addresses. I don't speak cisco, so I'm using the built in interface to configure it.If i choose IPoA I can enter the IP settings. If I choose PPPoA I can enter the username and password.I do not see anyway I can enter both the IP settings and the username + password on the WAN configuration page.
View 9 Replies View RelatedSo i can't access my Facebook page i log on it fine at school & I used google chrome & safari, & internet explorer and every time i log on it says SSL Error & it also says that "you attempted to reach www.facebook.com, but instead you actually reached a server identifying itself as *.vkontakte.ru this may be cause by a misconfiguration on the server", idk what to do. I did everything, cleaned it for viruses and checked the proxy & everything.
View 5 Replies View Relatedwhen I got my new computer, I couldn't access the login or registration page of the site. I try accessing it through my cellphone or through a different computer or device (iPads etc.) nd it works just fine... basically, it's not the site's problem, it's most likely in my computer's settings.
View 6 Replies View RelatedIt usually consists of installing routers in units. Occasionally I have to change the routers IP address to keep it from conflicting with other routers. To do so, I need to get to the router options to do that. Normally, typing in 192.168.0.1 gets me there with no problems. Sometimes it's a 10.0.10.1. (They have D-Link DIR-615 routers.) To make sure I know which address I need, I use the cmd and ipconfig /all. Some of the routers spit out an IPV6 address instead of the IPV4 that I need to access the router. Even after a factory reset, it still does this. I can't get in to change anything.
View 4 Replies View Related