Cisco Routers :: SRW2048 - Web Configuration Page Requires IE?
Jul 21, 2012
I'm currently trying to setup a Linksys SRW2048 switch.
The switch came with version 1.0.0 of the firmware (circa 2005), which worked fine with Google Chrome and Safari on OSX.
However, I recently upgraded to 1.2.2 (circa 2009), and the in-built web configuration page doesn't seem to work in anything except for IE6 or IE7.
Chrome and Safari give me a whole bunch of resource not available errors, and the page itself doesn't render properly at all:
Firefox also doesn't render it properly either:
It seems a bit strange on Linksys/Cisco's part that they'd release an updated firmware that meant their switch could only be used by Internet Explorer.
Or failing that, are there any known workarounds to get this to work with Chrome, Safari, Firefox - anything other than IE? Or anything on OSX or Linux?
Also, I heard that firmware 1.2.1 still works on non-IE browsers - any archives of older Linksys switch firmwares?
View 2 Replies
ADVERTISEMENT
Feb 15, 2012
Linksys tried multiple WRT54g routers and access point, 192.168.1.1 can't open the router config page.
View 5 Replies
View Related
Aug 22, 2011
I'm moving from an 1801W to an SRP547.My adsl supplier (BT) has given me a username and password, and also a router IP address, a subnet and an gateway IP address. I have 13 fixed IP addresses. I don't speak cisco, so I'm using the built in interface to configure it.If i choose IPoA I can enter the IP settings. If I choose PPPoA I can enter the username and password.I do not see anyway I can enter both the IP settings and the username + password on the WAN configuration page.
View 9 Replies
View Related
Oct 14, 2012
N+ requires constant reboots to maintain speed. When I reboot the router F5D8235-4 v3 it will run at top speed of 10mbps, after a day or two it slows to about 2mpbs. A reboot will speed it up again. I would prefer that it run fast all the time. Firmware 3.00.15
View 12 Replies
View Related
Jul 17, 2012
I cannot access the configuration page for wifi router... my wifi router is buffalo WHR-G300NI usually access the page via 192.168.11.1but since I have plugged the wire from the internet socket on the wall to LAN port rather than WAN port and disable the DHCP , I cannot access the configuration page and I cannot change these because the ISP told me to do in order to access the internetIs there any other way to access the configuration page?if there isn't, how can I access to the configuration page
View 1 Replies
View Related
Apr 8, 2011
I need to access my modem config page which I could access months ago. In Start, Run, cmd, ipconfig, my default gateway is "192.168.1.1". when I type it in Chrome Browser it says Error 324(when antivirus on) and Error 101(when antivirus off). Tried with explorer (cant connect), Firefox(says done and a blank page) and opera, none working.The last time I could connect to that configuration page was like 4 months ago but I think I did something wrong and can't do it anymore.
View 19 Replies
View Related
Jan 19, 2013
I get disconnected from my ADSL2+ connection now and then and it is starting to irritate my a lot so I want to investigate the problem, but I can't access my modem config page. The modem is a Zhone 1511-A1 and the default ip is 192.168.1.1. I tried to reset the modem to isp configs and it did not work. When I ping my address it says "TTL expired in transit". I really don't know what to do next to get into this config[CODE]
View 6 Replies
View Related
Jan 4, 2013
I have a wireless Netgear extender, and can not find set up page..Can't access own router configuration page
View 3 Replies
View Related
Aug 17, 2011
I've got the DIR-825 2.02. I had an issue where if you did change the IP adress default 192.168.0.xxx to something like 192.168.yyy.xxx, the configuration page was becoming inaccessible. It was super slow, was displaying the wrong pages with missing images and wrong page formating. I had to reset the router to default and then it was working fine.That seems to have been fixed since 2.05. Now you can change the default ip adress to anything you want and the configuration or setup still work fine.When I am on LAN, the setup page are displayed almost instantly. By remote, it's super slow.
View 1 Replies
View Related
Aug 8, 2012
I have the issue of being unable to access my router configuration page. My standard gateway IP (83.226.48.1), does not work, resulting in "unable to connect". If I try with my IPv4-adress, it just comes out with a blank page (Mozilla Firefox and Internet Explorer).
View 17 Replies
View Related
Dec 6, 2011
first off I was trying to change my ip address to dynamic from static, turns out I cant manually, anyways I was messing around with the configuration on my modem page (192.168.0.1) trying to enable dhcp because I know that if it shows that its not enabled yet I get my ip address automatically, it means my ip is static. I enabled a few things like netbios over tcpip and such and something to do with dns routing but I cant recall all I did and in what order because I can no longer get into the config. page and I cant connect to the internet and when I use command promp to renew my ip it says "an error occured while renewing interface local area connection... unable to contact your dhcp server and also an error occured while releasing interface loopback psuedo-interface1 : the system cannot find file specified.
View 2 Replies
View Related
Jan 29, 2012
I have been trying to configure some settings on my modem and to do so I must access it from it's ip (192.168.250.1). However, when I load that ip in my browser it does not connect.
My router has a private ip of 192.168.0.1 because of a Double NAT issue which I am trying to fix by going to the modem's configuration page. I am pretty sure that it is 192.168.250.1 because that is what my router ISP Gateway says, along with ipconfig in cmd when I directly connected to the modem from my computer.
By the way, I am currently connected through my D-Link 254 router which is connected to my WiMax modem.
View 2 Replies
View Related
Oct 11, 2011
I have a D-Link dsl 2640u, it's a modem but since it has 4 ports im assuming it's also a router. My problem is that when i enter my ip address into the address bar it doesn't recognize it. I can't use Utorrent or anything that requires ports to be opened..and it's a pain in the butt. when I type ipconfig on my command prompt it brings up..172.16.X.X and when i enter it into the address bar nothing is found. I'd like to port forward by accessing the modem's config page.I read on another thread that i could set my own ip address by going to: Control Panel>Network and Sharing center> Local Area Network>Properties of Ipv6 and typing my own ip address but when i do this i lose my internet connection.
View 14 Replies
View Related
Mar 13, 2012
My router/modem is a DSL-2740BI created a hostname [URL] At my service provider I was able to create a DNS setting where I specified my routers IP address.In my router I think I created a port forward (TCP port 8080 on both external and internal) with the ip address of a small "web server" (an Arduino module for home automation).When I enter my hostname I get to see my router config page instead of my "Arduino page".
View 7 Replies
View Related
Nov 18, 2012
I have Time Warner[Road Runner] and an ARRIS TG862 router. I have tried cmd->ipconfig->and connected through the address shown[Default Gateway;192.168.0.1] and have tried an ipconfig/ flushdns -> /release ->renew as well to no avail. Is there anything I could do to access the page? P.S. This was all done through a Windows 7 desktop connected directly to the router through an Ethernet cable
View 5 Replies
View Related
Nov 22, 2010
I bought this wireless router the other day in order to get internet access on my Nintendo Wii. I set it up using the CD and followed all the instructions (made a password, wrote down the key, etc.) - and my Wii CAN detect it, but when I type in the key on the Wii I get an error message. I looked online and they said the way to fix that specific error is to "change the channel" on the router to 1 or 11. (It is currently 6). I type in my IP into the browser like I'm supposed to (the default IP of the router), but ALL the options on the page are greyed out and nothing is click-able. Here's a screenshot
View 3 Replies
View Related
May 9, 2012
I have a D-Link DSL-2520u ADSL2+ modem. When I access the page 192.168.1.1, it prompts for a username and password. Upon successful authentication, I see the modem configuration page.
If I am on a different network, I can also access the modems configuration via its public IP address.How can I restrict access to the configuration page via the public IP address and only allow access via the internal IP address?
View 1 Replies
View Related
Aug 30, 2007
My question is regarding gaining access to my Linksys wireless router configuration page. I recently turned my Linksys WRT54GL wireless router into an access point and since I have done so I am no longer able to access the configuration page for my router.
The problem that I am encountering is not one of connectivity, but rather entry. Prior to turning my wireless router into an access point I was able to connect to the router by means of my browser (192.168.1.1). I am still able to connect to the router, but whenever I type in a user name and password the router just simply does not recognize the information. I have tried resetting the router multiple times, but I am still denied access to my router despite having the correct user name and password. I have version 1.1 of the Linksys WRT54GL wireless router and have the latest firmware.
View 9 Replies
View Related
Mar 26, 2013
Region : Others
Model : TL-WR841N
Hardware Version : V7.2
Firmware Version : TL-WR841N_v7_120201
ISP :
I recently encountered a problem with my router. It's configuration page is not accessible quickly. When I opened it ( by typing 192.168.1.1 in my browser) it took ages to open and even when it did, the page lacked a lot of features i.e., it did not load properly. Then on a suggestion by a friend, I downloaded the latest correct version (I have an IQ above 60) for my router but the problem persisted. And it is only on my PC. When I access it from some other PC, it opens as it should. My router is only 6 months old.
View 4 Replies
View Related
Nov 4, 2011
I have the next config: PC -> Asus RT-N16 router (192.168.1.1) -> LinkSys WAG54G2 in bridge mode (192.168.0.1),How can I access to modem's config page from my PC ?
View 2 Replies
View Related
Feb 5, 2011
I have been using this router for 6 months without problems. However, it hasn't been working since yesterday morning. It receives power but the Internet led doesn't light up. The network leds are blinking faintly and rapidly. I can't access the configuration page from my browser. Is it dead or not?
View 9 Replies
View Related
Oct 25, 2012
My internet connection is fine but I really need to update the firmware on my wireless adapter. I have no problem accessing the router's config page. I ran ipconfig to get the adapter IP (screenshot attached/192.168.2.104). When I type the IP into the browser I get the "cannot display webpage" msg. I have tried turning off the power to the router, disabling Norton's firewall (I disabled Norton completely), and nothing works. Do not tell me to restore factory defaults on the adapter because I tried to get to the configuration page of another wireless adapter I have and am having the same problem.
View 7 Replies
View Related
Apr 9, 2012
I have Verizon FIOS internet/wireless router and then a WRT310N wireless router connected to it thru Ethernet cable. I want to disable DHCP in the Linksys, but when I try to access the set up page at address 192.168.1.1 the Verizon router set up page shows up. I've tried to connect the router directly to the computer, but it needs the internet connection from the Verizon router. How do I get to the set up of the Linksys at the same time the Verizon is using the same address?
View 5 Replies
View Related
Sep 14, 2011
It baffles me because the admin console doesn't look like it will browse your computer for a firmware update. Rather, it prefers you to specify a tftp or http server. I don't know how I'd set up my computer to be the http or tftp server and it doesn't really go into detail on what configurations or commands that would need to be used. I've used a tftp client in the past to send a firmware to routers and whatnot but not serve one.
View 1 Replies
View Related
Aug 8, 2011
How can I access the we interface of this switch if it is configured to get its IP address from the DHCP server? Since it is DHCP I do not know what IP address has been assigned to it therefore I do not know what ip address to enter in the browser.
View 9 Replies
View Related
Aug 22, 2011
SRW 2048-EU(webview) switch will support how many SFP minigibic whether 2 or 4 ?
View 1 Replies
View Related
Apr 24, 2011
I can't access the WEBGUI on any of them. they are very busy, the network is working fine, but I can't connect to the webgui on them. I've even had problems with a few connecting to them via HyprTerm. I bought 7 of the 12 just last May. If I'd known they were end of life I wouldnt have purchased these, although they are an awesome 48 gig switch for the price.
I need to be able to VLAN these. How can I get back in? Power cycle?
View 3 Replies
View Related
Jan 4, 2013
Trying to replace 3Com Superstack II Switches (3C16980) with 100Base-FX Modules (3C16970) with a Cisco solution. Existing Fiber connector in Network closet on both ends is an SC connector (picture attached). What Modules, adapter cables do I need to connect to an SRW2048 switch at one end an SRW2024 switch at the other? Will this solution provide a Gigabit connection over the Fiber ?
I am looking at using SRW2048-K9-NA with MGBSX1 module at one closet and SRW2024-K9-NA with MGBSX1 module in the other closet at the other end of the Fiber cable.
I found an adapter cable that will convert an SC male to an LC Male and it looks like it will work but I have no experience with fiber. I attached a picture of this adapter as well. It is listed on line as - 1ft Fiber Optic Adapter Cable LC (Male) to SC (Female) Multimode 62.5/125 Duplex
View 2 Replies
View Related
Feb 24, 2013
Am trying to join a SF 300-48p 10/100 switch to a SRW2049 Gigabit switch.I purchased Cisco a SFP+ Copper Twiaxial Cable, but not getting a connection.
View 2 Replies
View Related
May 14, 2012
I have a Win 2003 server set up as my DHCP server. It is connected to port 13 of my SRW2048 switch.
Every port from 1-12 and from 25-36 get a "Limited or No Connectivity" error when I plug an ethernet cable in them from a computer (Win XP). However, all of the other ports receive an IP address and connect to our network just fine. I've noticed that they are all in the two right hand banks of ports,though, so I'm in need of assistance as to how I can get the first two banks of ports to behave the same way. In other words, I want all of the ports on the switch to be able to populate an IP address from the DHCP server attached to port 13.
View 8 Replies
View Related
Oct 25, 2011
I am trying to track down the SNMP MIBs for the Linksys by Cisco SRW2048. Please note that this is the model before the complete CISCO rebrand of the product. I have SNMP walked, browsed etc etc and I just can't pull CPU and RAM usage. Any working view of those two stats? I'm using OpManager by ManageEngine as my NPM platform.
View 1 Replies
View Related
Aug 14, 2011
I believe the SRW series is the same basic hardware as the SG300 series.Is there a way to upgrade the firmware on the SRW series using the SG300 firmware?
The SG300 firmware is much more usable. Also I'd rather have consistency as we have the older SRW2024/48 and the newer SG300 switches.
View 2 Replies
View Related
Mar 13, 2011
I did RECOVERY on my computer. Its a Compac Windows XP Home edition. This computer runs off of my main computer by a router & adapter. My router & adaptor are showing green but the Internet is showing red. Its becuz my high speed Internat service is ATT.my.yahoo.com. which comes through IE. On my newer computer all is fine. My IE works good & all is working. but my IE on my older one which runs with the router wont set up.
View 1 Replies
View Related
