Cisco Switches :: SRW2048 - Cant Access WEBGUI
Apr 24, 2011
I can't access the WEBGUI on any of them. they are very busy, the network is working fine, but I can't connect to the webgui on them. I've even had problems with a few connecting to them via HyprTerm. I bought 7 of the 12 just last May. If I'd known they were end of life I wouldnt have purchased these, although they are an awesome 48 gig switch for the price.
I need to be able to VLAN these. How can I get back in? Power cycle?
View 3 Replies
ADVERTISEMENT
Aug 8, 2011
How can I access the we interface of this switch if it is configured to get its IP address from the DHCP server? Since it is DHCP I do not know what IP address has been assigned to it therefore I do not know what ip address to enter in the browser.
View 9 Replies
View Related
Jan 15, 2012
we are starting to replace low budget hubs by the SG-300's. On the accessports we use BPDUguard and mac security (max 1 user per port).
The newest firmware is used (1.1.2.0).
When i lock a port intentionally by connecting e.g. ports 4 and 5 together (something that happens quite frequently by user-faillure) i do not see this in the WEB gui.
The CLI does tell me that the port is locked:
gi4 1G-Copper -- -- -- -- Down* -- --
*: The interface was suspended by the system.
In the webGUI i can reset the port, but in the CLI i don't get how i should do this. I tried a 'shutdown' followed by a ' no shutdown' on CLI interface level, but that does not lift the suspension state.
Questions:
- Possible to lift the suspension state using the CLI ?
- Is there a way to see the lockdown in the webGUI ?
View 4 Replies
View Related
Aug 22, 2011
SRW 2048-EU(webview) switch will support how many SFP minigibic whether 2 or 4 ?
View 1 Replies
View Related
Jan 4, 2013
Trying to replace 3Com Superstack II Switches (3C16980) with 100Base-FX Modules (3C16970) with a Cisco solution. Existing Fiber connector in Network closet on both ends is an SC connector (picture attached). What Modules, adapter cables do I need to connect to an SRW2048 switch at one end an SRW2024 switch at the other? Will this solution provide a Gigabit connection over the Fiber ?
I am looking at using SRW2048-K9-NA with MGBSX1 module at one closet and SRW2024-K9-NA with MGBSX1 module in the other closet at the other end of the Fiber cable.
I found an adapter cable that will convert an SC male to an LC Male and it looks like it will work but I have no experience with fiber. I attached a picture of this adapter as well. It is listed on line as - 1ft Fiber Optic Adapter Cable LC (Male) to SC (Female) Multimode 62.5/125 Duplex
View 2 Replies
View Related
Feb 24, 2013
Am trying to join a SF 300-48p 10/100 switch to a SRW2049 Gigabit switch.I purchased Cisco a SFP+ Copper Twiaxial Cable, but not getting a connection.
View 2 Replies
View Related
Apr 26, 2011
I recently put in a Netgear firewall, configured it, its running no problem. Then I setup a new Netgear N600 wireless router, configured it, gave it a static IP, connected to it, works like a charm. Thing is, when I try to access the web gui I receive nothing.. Is the Netgear firewall taking priority or something? I went directly connected to the netgear wifi router and double checked to make sure that there was no settings restricting administration from wifi users, etc..
View 3 Replies
View Related
Oct 25, 2011
I am trying to track down the SNMP MIBs for the Linksys by Cisco SRW2048. Please note that this is the model before the complete CISCO rebrand of the product. I have SNMP walked, browsed etc etc and I just can't pull CPU and RAM usage. Any working view of those two stats? I'm using OpManager by ManageEngine as my NPM platform.
View 1 Replies
View Related
Aug 14, 2011
I believe the SRW series is the same basic hardware as the SG300 series.Is there a way to upgrade the firmware on the SRW series using the SG300 firmware?
The SG300 firmware is much more usable. Also I'd rather have consistency as we have the older SRW2024/48 and the newer SG300 switches.
View 2 Replies
View Related
Feb 24, 2013
I have lost the original console cable to the Cisco Linksys SRW2048 and was wondering if I can use the Cisco console cable or can a regular serial cable with female ends will work?
View 2 Replies
View Related
Jun 20, 2012
I have installed lms 4.1 on a windows 2008 server however after installation, the webgui cant be launched
View 3 Replies
View Related
Jul 25, 2009
Is there any way yo restart the WRT160NL from the web interface? I've had several routers before this Linksys and all of them had this option. In the web GUI of the WRT I can't find the way to do it and I have no other solution of unplugging it and plugging again.
View 6 Replies
View Related
Sep 14, 2011
It baffles me because the admin console doesn't look like it will browse your computer for a firmware update. Rather, it prefers you to specify a tftp or http server. I don't know how I'd set up my computer to be the http or tftp server and it doesn't really go into detail on what configurations or commands that would need to be used. I've used a tftp client in the past to send a firmware to routers and whatnot but not serve one.
View 1 Replies
View Related
Jul 21, 2012
I'm currently trying to setup a Linksys SRW2048 switch.
The switch came with version 1.0.0 of the firmware (circa 2005), which worked fine with Google Chrome and Safari on OSX.
However, I recently upgraded to 1.2.2 (circa 2009), and the in-built web configuration page doesn't seem to work in anything except for IE6 or IE7.
Chrome and Safari give me a whole bunch of resource not available errors, and the page itself doesn't render properly at all:
Firefox also doesn't render it properly either:
It seems a bit strange on Linksys/Cisco's part that they'd release an updated firmware that meant their switch could only be used by Internet Explorer.
Or failing that, are there any known workarounds to get this to work with Chrome, Safari, Firefox - anything other than IE? Or anything on OSX or Linux?
Also, I heard that firmware 1.2.1 still works on non-IE browsers - any archives of older Linksys switch firmwares?
View 2 Replies
View Related
May 14, 2012
I have a Win 2003 server set up as my DHCP server. It is connected to port 13 of my SRW2048 switch.
Every port from 1-12 and from 25-36 get a "Limited or No Connectivity" error when I plug an ethernet cable in them from a computer (Win XP). However, all of the other ports receive an IP address and connect to our network just fine. I've noticed that they are all in the two right hand banks of ports,though, so I'm in need of assistance as to how I can get the first two banks of ports to behave the same way. In other words, I want all of the ports on the switch to be able to populate an IP address from the DHCP server attached to port 13.
View 8 Replies
View Related
Jan 2, 2013
I have a problem with my switch. The model no. of the switch is as follows:
Linksys SRW2048 10/100/1000 48 Ports
Serial No: RJT00GC00395 GGR2906 MM
1. I am creating a home computer lab. I do have 3 servers HP ProLiant DL 385 G1. Two of them have 6 gigabit ports where as the third server has 2 gigabit ports.
2. Installed ESXi 5.1 on two servers where as installed FreeNAS on the third server and configured it as iSCSI storage and NFS storage.
Problem:
1. Every port works perfectly fine. However, when I keep connecting the ports of the switch to the ports of servers, internet gets disconnected.
2. Interestingly, my wireless internet also gets disconnected, the ports of the switch does not have any internet now.
3. This happens till I connect above 8-9 ports of the switch to the servers.
3. However, when I remove the connection between the switch and the servers, internet comes, wireless internet starts working; and the port of the switch also gets internet connection when I check the internet connection of the individual ports one at a time.
Some more information:i do have internet service provided by Time Warner Cable. My internet speed is as follows:
Download Speed: Up to 15 Mbps
Upload Speed: Up to 1 Mbps
I do have a modem *** router by Motorola which has 4 gigabit ports.Model no: Motorola SURFboard SBG6580 i am assuming it is some thing related to bandwidth of the internet.
View 4 Replies
View Related
Oct 23, 2012
I want to connect two linksys SRW2048 through fiber optic.. it's located different rooms with fiber optic....Is it possible through VALN....This setup using for CCTV connectivity?
View 1 Replies
View Related
Feb 16, 2012
So I have read about proper procedure involving the connection between a console cable and Hyper-terminal. I have also tried plugging into a network port to obtain an IP Address but nothing seems to work. When powering on the switch I see that it lights up, hear fans spin and assume it has booted properly. I'm using Hyperterminal on Windows Xp Pro SP3 and I've also tried minicom in Fedora.
And just FYI Hyperterminal was set to the proper:
Bits per second: 38400
Data bits: 8
Parity: None
Stop Bits: 1
Flow Control: None
View 1 Replies
View Related
Dec 27, 2012
I just picked up a pair of 18-port SG200s, and I'm trying to figure out of there's some secret trick to getting CLI access to them? I've upgraded to the latest version of firmware (1.2.7.76) hoping that may work, but no luck.I can tell the guts to support a CLI are there, because writing the config out to a TFTP server shows identical an identical config style to the SG500 I have here.Is there some way to enable it?
View 5 Replies
View Related
Jun 22, 2012
I'm having some difficulties with the VLAN setup on the SG-200 and the WiFi access point. The access point (a TP-Link WA801N) is only able to access the internet when it is plugged into a port that is on the default VLAN (PVID 1). If I plug it into one of the other VLANs then any clients connected to the WiFi lose access to the internet and cannot access devices on the VLAN. I have previously used this setup with a first generation Cisco WAP4410N. [code]
View 4 Replies
View Related
Mar 29, 2011
I am trying to setup internet access and intranet access using two cards per PC. I don't have sever software and I want to be able to share files between several machines. I have two routers. One that connects to cable modem and one that connects to intranet side. I have assigned different static ip addresses to both cards.
View 6 Replies
View Related
Feb 24, 2013
I connect to switch Access Point, configure port on switch which vlan work on this port. But after reboot AP my config for this port delete and have other config where vlan 1 untagged, and allow all other vlan. But in my cinfig allow 3vlan: untagged 100, and tagged 113, 999.
View 1 Replies
View Related
Jul 22, 2012
I have a SG 300 switch and configured it with public IP address.I can access it from anywhere within my network but not from outside my network as I'am not able to add the gateway and DNS address as there are are no fields to add them in the IP configuration menu in L3 mode.
View 1 Replies
View Related
Jan 30, 2012
Trunk from 3500 going into SF300-8 #1 QNQTrunk from SF300-8 #1 going into trunk SF300-8 #2QNQ from SF300-08#2 going into Trunk SF300-24, All Vlans from Network 1 seem to be communicating properly between the 3550 and SF300-24 and is isolated from the Transport Network by QnQ. I am having one problem, I can not ping the SF300-24 or get to the management interface. I am able to access other devices on the SF300-24 Vlan1 from devices on the 3550 Vlan1 and vice versa.
View 1 Replies
View Related
May 18, 2011
I have an SF 300-08 switch with three V-LANs assigned to it. One is dedicated to the management of the device and the others are development boxes.
Right now, to access the switch, I have to go into the TCP/IP properties and assign a subnet within VLAN1 (subnet linked to the management interface). Then to access the interent, I simply remove the settings, as I have another VLAN linked to a subnet from my router.
Is there a way to configure the switch that allows the ability to access both without configuring the TCP/IP settings to be on the other subnet? I do not think so, but it is worth a try.
View 2 Replies
View Related
Sep 25, 2011
How does one remotely access a SG300-28P?
View 2 Replies
View Related
Nov 17, 2011
In our network two Domain Controllers are configured as the central (S)NTP Servers. For a switch in Layer 3 mode it is quit easy to synchronise with these (S)NTP Servers. But what is actually the best approach for access switches in layer 2 mode, that are connected to the layer 3 switch? The only IP Address they have are part of the management VLAN ID 1 which is not routable. I am actually looking for something like a broadcast without having to put a NTP Server in management vLAN.
View 4 Replies
View Related
Oct 31, 2012
I'm having troubles setting up a separate VLAN for wireless on a SG-200-26. My first question is why did Cisco not make the VLAN setup like they have all their other business class switches? Anyways, the Access and General modes on these SG class switches are throwing me for a loop.
Right now I just have one port (g10) on the SG-200 switch that needs to be in VLAN 6, which is our wireless VLAN. All other ports are in their default VLAN, which is 1.
Here's what I've done...
Configured port G1 (trunk to another switch) as the trunk port and Port G10 (attached to WAP) as a general port. All other ports stayed in their default configuration. This is what it looks like now...
Port Mode PVID Operational VLANs
g1 Trunk 1 1U, 6T
g2 Trunk 1 1U
[Code].....
I'm pretty sure port G1 is configured correctly, but I have no idea about what port g10 should look like. Common sense tells me it should be an Access port and assign it to VLAN 6, but apparently you cannot tag the traffic within an Access port on SG switches, which makes it useless because how will other switches recognize what VLAN the packets are in? So the next logical mode would be General mode, which I put in VLAN 6. I switched that port from being 6U (untagged) to 6T (tagged), but neither seemed to work.
VLANs on SG switches, how port g10 should be configured for VLAN 6 traffic.
View 4 Replies
View Related
Apr 27, 2013
I have a problem with my SG200, maybe more than one.
I tried to update to 1.3.0.59 this morning. It succeeded and the switch was restarted. After the restart I could no longer log into the switch. I tried to reset the switch but it still will not let me log in. I also tried to log into the switch using the forllowing method but I still cannot log in. I unpluged everything, held the reset for at least 30 seconds, waited 3 minutes, plugged a computer in and set it up to see the switch. All worked there and the login page appeared. It still would not take my login dredentials nor wold it that the default credentials. I has access through the switch but connot configure anything.
View 4 Replies
View Related
Apr 17, 2011
I’ve recently brought a SG 300-52 for my company with the main intention of using the L3 switching, I’ve recently gone on a 3day cisco course and came backing thinking i knew what i had to do but as always if you don’t have the experts next to you to answer the questions you soon have problems.
I have setup 3 VLANS, the switch is basically on its default settings and VLAN 1 connects straight to the router/gateway and on the internet but VLAN 2 and 3 do not, they are completely localy contained to their own Non DHCP networks.how do I get VLAN 2 and 3 on the internet and able to talk to each VLAN?
The keywords I’ve came across in my search are static routing between VLANs and InterVLAN, I’m assuming i need to do one of these??
View 26 Replies
View Related
Aug 3, 2012
we just bought a Cisco SG200-18 to replace our Linksys DLM2008 switches. Now we face a problem with remote desktop between our Win7x64 boxes.
Remote access is abysmally slow, but file transfer speeds seem to be normal. All ports are on Gigabit setting, jumbo frames disabled. The switch on the latest firmware.
View 6 Replies
View Related
Apr 5, 2011
I have this Cisco Switch: SRW2048-K9-NA. When I log into the Web GUI, I am provided the two options mentioned above for VLAN Management. I have fiddled with the two options and they seem identical to me. Is there really a difference, maybe better flexibility?
View 2 Replies
View Related
Mar 29, 2013
I have windows 7 could this be the problem? it is unsecure and I have access the security part of it
View 1 Replies
View Related
