Add Samsung E5500 Blu-ray Player To Access Point Via Ethernet?
Dec 27, 2012
I have set my Linksys WRT120N as an Access Point by connecting it to my primary router via Ethernet. To the Linksys WRT120N I have connected via Ethernet a Samsung BD-E5500 player.Through the Linksys WRT120N Access Point, I am wirelessly able to browse Internet through my cellphone, however, E5500 keeps reporting that while it is connected to the network, it is can not connect to the Internet. The Network Settings is Wired and Auto for IP and DNS.
View 3 Replies
ADVERTISEMENT
Apr 9, 2012
I have practically NO knowledge of networking! So I've been tearing my hair out trying to get this darn thing sorted but to no avail.So, I've bought a Samsung BD-E5500 blu-ray player which has internet capability either through Ethernet or a Samsung wireless adapter. I am not willing to spend an extra £40-£70 on an adapter and obviously don't relish the idea of running a very long cable to my router upstairs. However the general concensus is that it's possible to take a cable out of the Ethernet and into a wireless AP or router, using it as a bridge to the main wireless router. So I have tried this and failed, of course not having a clue as to what I'm really doing. I have a Netgear ME102 access point which the player can't seem to get on the network with at all and also I have tried using a Belkin F5D7632 wireless router. Now, with the Belkin router the player does say that it can access the network, however it says that it cannot access the internet. The wireless router that I have upstairs is an O2 Wireless Box 3.
View 3 Replies
View Related
Jan 10, 2011
after i enter the security key for my router it says it is unable to connect to the network. it also has me manually put in my ip address and it says my gateway ping is incorrect. where do i find this information
View 1 Replies
View Related
Jun 28, 2011
I have a Samsung BD-C5500 Blu Ray player and am using the Samsung PC Share Manager software. For some reason, the software is not recognizing the player. However, the player is able to connect to the internet (I stream Netflix). I am running Windows XP service pack 3 and both my BD player and PC are connected to the same router (D-Link 601). IP address for BD player is 192.168.0.102 and PC is 192.168.0.100. BD player firmware is up to date.
View 1 Replies
View Related
Aug 15, 2011
im trying to get netflix but i cant get my blueray player to connect to the internet,everything is hooked up and turned
View 1 Replies
View Related
Sep 18, 2012
I got no code, and as a matter of fact have no Internet connectivity to my Bluray player. When I go to my Bluray setting tab and run a network test the MAC Address checks out but fails when it gets to IP Address. My Bluray is plugged directly into my router and it still shows no Internet connection between the two, even though my x-box 360 has no problem nor does my computer. When looking at my network settings the IP Addresss boxes all have numbers in them, the Subnet Mask boxes two of four boxes have numbers the others are zeros, the Gateway boxes are all zeros, and the DNS Server boxes are all zeros. I read many of the posts in this forum and all problems seem pretty similar to mine.
View 4 Replies
View Related
Aug 23, 2011
How do i configure my netgear router to my samsung blu-ray player to allow wireless connection?
View 2 Replies
View Related
May 12, 2010
As the subject says, I've hooked up a Samsung BD player to a BEFSR41 router. The router has the current firmware version. When I run the connection test for the player, the local connection is good but the Internet connection fails and the message is " The HTTP port is disabled."
I've searched high and low for a solution to no avail. I did searches on the forum and couldn't find anything. As a test, I connected the BD player directly to the DSL modem and the Internet connection worked perfectly so it appears that the blockage is within the router.
I've serched through the router setup and have changed most settings to try and find something that would work. Nothing worked so I have returned my setup to its original state.
View 7 Replies
View Related
May 9, 2012
If I hook up a wireless router as an access point will both the Ethernet ports and the wireless connection on that router work?
View 2 Replies
View Related
Jan 23, 2012
May I use an access point as wireless receiver to have internet on RJ45 interface?Is possible that internet source for AP to be on antenna, not on RJ45?
View 4 Replies
View Related
Feb 22, 2011
I bought a Philips blu ray player that has an ethernet port to connect to stream movies. My router is located on a different floor so connecting via an ethernet cable is not an option. How do I connect my blu ray player on the 2nd floor to the router on the 1st floor?
View 2 Replies
View Related
Jun 6, 2011
I have just bought a TP-Link Wireless Access Point (TL-WA&01ND) and an ethernet switcher (TL-SF2005D).I have put the access point into client mode, allowing me to put it in my room and wirelessly connect to my router, allowing me to plug my PC in over ethernet and use the internet. However, after much fiddling with settings I cannot get it to work, as it continually searches for a network, and then fails to connect, despite the fact it is configured to use the network?I already have a similar setup with a netgear wireless G access point which works, and so I dont understand why the new box cannot do this when using what I believe to be the same settings.
Secondly I have an ethernet switch box which I bought to connect to the access point and switch the ethernet signal between my two PCs, my xbox and PC. This works fine with my primary PC (over my old access point) but when I try to connect my PC i get a DNS failure with auto IP settings and a gateway failure with manual settings, and other devices refuse to connect.
View 9 Replies
View Related
Dec 20, 2012
after installing Windows 7 Professional on my netbook, there has been a problem. I think it may be a problem with the wireless card or something..?
But anyway, before I had Professional, I had Starter, and that worked perfectly with the wireless internet. Now, however, I can only connect through ethernet. I know it is definitely a problem with my netbook, as before, the netbook could recognize all the routers, etc., on the street, and now it can't even recognize the router right next to me. Also, my phone is able to connect to my router perfectly fine...
I am running a Samsung N130 Netbook with Windows 7 Professional (x86), I bought the netbook at around November 2010 .
View 7 Replies
View Related
Sep 18, 2012
I took my samsung RV510 back to factroy setting and now have no wireless only works on ethernet cable
View 2 Replies
View Related
Sep 22, 2012
i have a Samsung RV520 lap top Intl core 3 OS windows 7 and it has recently Crashed. i re installed the OS then win it was back up the wireless Ethernet "WiFi" was not installed on the system tried to install it with the default drivers. The Drivers did not work. the software on the computer i am looking for is the Intel centrino wireless-N + WIMAX 6150. I started to look for online could not find the version for windows 7 the only one i can find is vista. So i was wondering if any one knows where to get the drivers?
View 1 Replies
View Related
Apr 16, 2013
I need to know if 3502p with outdoor antennas supports Point-to-Point Wireless Bridging?
View 6 Replies
View Related
Jul 15, 2012
Is it possible to run 802.1Q on a point to point Ethernet circuit between 2 Cisco ISR routers? I need to carry multiple VLANs across an ethernet WAN circuit but not sure if a Cisco router would let me do this. I can surely lab up but was looking for expert opinion on what's best aproach to carry multiple VLAN across the WAN ethernet. Plugging the circuit to a LAN switch is not an option since this is a managed WAN router.
View 10 Replies
View Related
Feb 27, 2013
How would I bridge a wireless connection with a distance of 400 feet? Would twoAP1262N-A-K9 be able to make this happen? Or is there another wireless bridge that you all can think of?I would be connecting one AP1262 of off a 3750g switch and at the far end (400 ft aproximately) another AP1262N-A-K9.
View 12 Replies
View Related
Nov 1, 2012
How do I connect and configure my WAP54G wireless access point to my new Cable Modem? I have it connected to the modem but I cannot access it to configure it. It appears to be working but before I got the cable modem I had it connected to a router and it was set-up with a static IP address. With my new ISP, I no longer have a static IP address so I am trying to configure the WAP54G to use DHCP. Trying to access it thru the internet at 192.168.1.245 does not work.
View 1 Replies
View Related
Aug 29, 2009
I just bought an LG Bluray DVD player (BD390) which is unable to find the access point in my home network.My router is a WRT54G, ver. 2.2, running firmware: Ver.4.21.1. My home network uses high speed cable with two computers on the wireless network, all working with no problems.The router is on the second floor but the two computers and the new BD390 are on the first floor - about 35 feet away. I have the wirelss security set to none and use only the specific computer MAC addresses to allow connection to this network.
I found directions in the forum for a setup using the LG BD390 but with a different Linksys router. I changed the security to WPA (AES); the Beacon interval from 100 to 75; the Fragmentation Threshold from 2346 to 2304; and the RTS Threshold from 2347 to 2307. The DVD wireless connection still failed to find my network. There is a "Push button" connection feature on the BD390 setup which I tried, but the only "button" on the router I could find was in the basic wireless setting, a green icon for the wireless SSID setup. No connection was made there either.
The recommendation connection from the LG manual is for a network cable, but that would be over 50 feet and a real pain to connect, so I would prefer WiFi.
View 3 Replies
View Related
Apr 20, 2012
I had a new AIR-AP1042N-N-K9 access point and I tried to convert it into lightweight mode with the image c1140-rcvk9w8-tar.124-21a.JA2.tar . I used all the methods but the AP is getting hanged at one position after decompressing the new IOS. The capture of the process is below: [code] After this I am getting the junk characters and everytime AP hangs at this position.
View 4 Replies
View Related
Jul 9, 2006
I had to reset my access point but the login screen fails to appear to lock the router. I don't have the setup wizard disk.
View 9 Replies
View Related
Jan 17, 2013
I have a WAP54g hardware version 1.0.I install de last firmware on this access-point but, this access-point reset automatic after a random time..It’s it possible to downgrade de firmware from this access-point?
View 1 Replies
View Related
Dec 14, 2011
Have a WRT320N router at one end of the house in the basement. Would like to boost signal to other end of the house. Which product should i use, an access point or a range extender? My house is also wired with Ethernet cable and I could plug the access point into an Ethernet port at the end of the house where the signal is weak.
View 1 Replies
View Related
Jul 3, 2012
I have AP WAP 4410 N, and I want conected AP to cacti. Where is I faoun MIBs or OIDs for my Access Point?
View 1 Replies
View Related
Apr 25, 2011
I've got a AP WAP54G. I've managed to get into the configuration page and rename my router and set a WPA2-Personl password.
The issue I'm facing is that when me and my roomate try to connect to the router at the same time, it shows the laptop that connects second as one that has 'limited connectivity' and hence cannot use the internet. The 1st laptop however works fine!
The settings for the router have all been left to default.
I'm not sure, but does this problem have anything to do with the fact that the router in configured with a static IP. If so, then there is another issure which is that whenever I try to change it from static to automatic/dynamic IP, the page fails and the router doesn't even get connected to the configuraion page(192.168.1.245) after that. The only way to get that page again is the reset the router.
Also I'm not able to directly get into the config page when I connect my router to my laptop via lan. I need to change the LAN IP to 192.168.1.x where x is >1.
View 3 Replies
View Related
Feb 15, 2012
I have 2 data centers miles apart. They are on a Paetec MPLS. I have a Lightower point to point Ethernet link between the two data centers as well. At data center A, I have a Paetec managed router (192.168.2.1). The subnets behind that router are 192.168.2.0, 192.168.100.0 and 192.168.101.0. I also have a Cisco 1841 that is configured with fa0 addressed as 192.168.2.250 and fa1 as 10.5.5.1. Fa1 is the one end of the point to point Ethernet link to data center B.At data center B, I have a Paetec managed router (10.0.2.1). The subnets behind that router are 10.0.2.0, 10.0.100.0 and 10.0.101.0. I also have a Cisco 1841 that is configured with fa0 addressed as 10.0.2.250 and fa1 as 10.5.5.2.What I want to happen is any traffic headed from data center A destined for 10.0.100.0 or 10.0.101.0 to be routed through the point to point Ethernet link. I had Paetec add routes in their managed router to route any traffic headed for 10.0.100.0 and 10.0.101.0 to my Cisco 1841 (192.168.2.250).I wanted to do the same for traffic destined for 192.168.100.0 and 192.168.101.0 from data center B. Paetec added the appropriate routes to the router at data center B.Now, if I trace from data center A to 10.0.100.45, I see this:
1 <1 ms <1 ms <1 ms 192.168.2.1
2 <1 ms <1 ms <1 ms 192.168.2.250
3 4 ms 4 ms 4 ms 10.5.5.2
4 3 ms 3 ms 3 ms 10.0.2.1
So the routing seems to be ok. However after it hits 10.0.2.1, it gets lost after that.Am I missing something? Is this a misconfiguration on Paetec’s routers?
View 1 Replies
View Related
Aug 25, 2011
What I want to do is the opposite of most configurations. I live on a small island with only one DSL connection. The modem is wired connected to a WAP54G Access point. To extend this access point want to use a WRT54G.
View 4 Replies
View Related
May 10, 2013
I'm using a WRT120N and have had no problems connecting most wireless devices, but a Nintendo DS and DSi owned by my family are unable to connect to the access point. My wireless security mode is disabled, network mode is set to mixed, SSID is the same as on the DS/DSi, Channel width is 20Mhz only, Standard channel is set to 6, but I tried using channel 1 and 11 without success, SSID broadcast is enabled.
I've tried every work-about I could find and always get the 51300 error code, and am at a loss as to what else I can try to get the devices to connect to the access point.
View 1 Replies
View Related
May 1, 2012
Is it possible to configure WRT120n as an access point?
View 1 Replies
View Related
Apr 6, 2011
I have 3 E3000 Routers and would quality input regarding using 1 of the E3000 Routers connected to my Broadband Modem (Roadrunner) and would like to know how to configure the remaining 2 E3000 Routers to be hardwired to my main Router as Access Points located approximate segmented 1/3rd areas throughout my house which really is only 1800 Sq.Ft. in area. How to be configure these routers as access points as well as configuring the main router that will be connected to my broadband router. This is my first network to utilize streaming video, Internet Television Programs, Internet Radio, Accessing the Internet in all rooms of my house and outside the immediate adjacent patio area.
View 1 Replies
View Related
Feb 10, 2012
I have tried to find mib for my Linksys WAP54G acces point without succeed. Any body know how I could find it?? I want to program a software based on SNMP protocol. Is there some databses for mibs?
View 1 Replies
View Related
Oct 7, 2012
Have a Samsung tablet supported by Verizon wireless. I need to connect to my home HP printer, but do not have broadband in the home, Can I connect the printer to a router and access via my tablet?
View 1 Replies
View Related
