Can't Access Internet Through Router?
Sep 21, 2012
I tried setting it up but if I connect the router to my laptop, I couldn't connect to the internet. While i was setting the wireless router, I couldn't access 192.168.1.1. I could only access internet through ethernet cable from my modem. I tried fixing it, power cycles, enabling the IP routing, but it hasn't fixed my problem. WHAT SHOULD I DO? The router lights are all functioning. The power, wlan, lan and wan lights are all stable.This is what my ipconfig looks like[CODE]
View 1 Replies
ADVERTISEMENT
May 31, 2012
I have 2 ISPs terminating on 2 FE ports on my 2811 router.ISP1 had always been here, used for the following:Internet access to LAN usersInternet access with public IP mapping to servers in different security zones (VLANS)Site to Site VPN tunnels to 3rd party partnersRemote VPN access to 3rd party partners We recently got a second ISP, mainly for the following:Internet access and public IP mapping to servers on seperate security zones (VLANS)Site to Site VPN tunnels to 3rd party partners as above, but different hosts So far, ISP1 and all the above service have worked based on the config below. However, having added ISP2, I have not been able to successfully create the site-to-site VPN tunnels.
version 12.4
!
ip source-route
!
ip cef
!
ip name-server 4.2.2.2
ip name-server 137.65.1.1
ip inspect WAAS enable
[code]....
Whenver I try to establish a tunnel on SDM_CMAP_2 and run a test using CCP, I get 2 failure reasons:
1. The peer must be routed through the crypto map interface. The following peer(s) are routed through non-crypto map interface - 4.58.130.130
2. The tunnel traffic destination must be routed through the crypto map interface. The following destinations are routed through non-crypto map interface - 4.58.130.134
The tunnels on SDM_CMAP_1 are all active Do I need to include a default route for the second ISP on the router? If so, how do I get this done? When I tried it, I had loops on the user LAN segment of the network.
View 5 Replies
View Related
May 18, 2011
Abruptly internet access disappeared. It's a router issue, none of the computers here can connect. Further, I can't access the router through a browser - 192.168.0.1 results in a "Firefox cannot connect" message. I've tried resetting the DNS to no avail. I'm typing via cell phone and it's annoying, but I'm willing to try about anything.
View 4 Replies
View Related
Aug 9, 2012
We have a home use WRT160N router linked to a PC desktop and two wireless laptops, Yesterday bought a new I-Phone, but could not link to my network (entered the security key many times). I accidentally connected to computer fix it firm that linked to my PC and wanted a large sum to fix the problem which he said was due to large number of temp?? internet files and once removed he would change the IP address of the desktop computer? Is this diagnosis logical and can I do it on my own. The router is definetely working - both laptops access the internet and I was recently able to hook up a Samsung Blu-Ray player using the same security code I used for the I-Phone.
View 1 Replies
View Related
Nov 4, 2011
I am trying to setup my E4200 to my new Cable Modem. I followed all of the procedures. I get Internet access when plugged directly to modem. I cloned the MAC Address and the Stus of the Router displays my current IP's (so I should have Internet). However, when I plug my computer into the Router I get no internet access.
View 3 Replies
View Related
Feb 20, 2012
I have a problem with the e4200 router and a mybook 1 TB connected to it. The media server works fine but after a while i loose contact with the router and the server this means that the Cisco connect doesn't work, the 192.168.1.1 doesn't work and I can't find the disk via \. I do have internet connection via wifi as im using it now....why I loose connection to the router? The lease time is 24h and it can happen more than once in a day.
View 4 Replies
View Related
Feb 2, 2011
I don't have Internet access, and this is for both a wireless connection and connecting to the router with ethernet.I do have Internet access when connecting directly to my modem via ethernet
View 3 Replies
View Related
Nov 3, 2011
I'm looking for a router that will let me hook up one PC to internet and have the rest of the network detached from the internet and all security issues, but still able to get to that one PC (and vice versa)....I don't want to do this with two network cards so am looking for a quick & easy hardware solution, if it exists....
View 12 Replies
View Related
Mar 23, 2012
I have a dlink router DIR-600 which was working fine. But to adjust some settings regarding Wireless, it got disturbed. Now the default ip address http://192.168.0.1 is not allowing to access the router and the internet. Here is the command list that is being given as per your post.
[code]...
View 1 Replies
View Related
Dec 18, 2011
Trying to set to unshare network. Locked myself out from router. Cannot access internet through router. How do I go back and reset correctly?
View 1 Replies
View Related
Sep 2, 2012
i bought the netgear wgr614v10 router yesterday from yesterday i was trying to connect to wifi but i could setup
View 3 Replies
View Related
Oct 24, 2012
I have a cox modem and a liksys wrt54g router. I cannot access the internet to set up the router. I have followed all the required steps in hooking up the router.
View 3 Replies
View Related
Aug 19, 2012
Our power went out yesterday. Had to reinstall router. Two computers are fine. One HP w/win 7 laptop has router connection, but no internet access.
View 2 Replies
View Related
Jan 10, 2013
Im having some problems connecting to the internet. my router is perfectly connected but i cant have wireless internet connection. when i plug the cable in the wall socket and in my computer, it works perfectly. But when i try to plug it in my router to have wireless, it doesnt work. Ive tried resetting the router or installing it again. but it doesnt work.
View 4 Replies
View Related
Oct 5, 2011
I am using wireless internet via D link router.I am connected to the router but there is no access to the internet.There is a small yellow triangle appearing on the wireless Network icon at the right bottom corner of my laptop.I can browse and download but I am getting the message that no internet access.
View 10 Replies
View Related
Feb 21, 2012
Current set up all worked fine for years (wireless Netgear router, ISP AOL ) until I changed my phone provider to AOL last week. On the day of the switch I lost my internet and have not had it since.Countless calls to AOL, line checks done and all showing as clear. Technician out today and no internal faults found.The internet light on the router is flashing orange, occassionally turning green but not holding. Router problems have been ruled out. Laptop shows communication with router but there is no internet access. This can not be a coincidence, I am sure something has gone wrong on the day of the switch since that is when the problem started.I am in really close range of the exchange and technician said I have good conectivity and wondered if there was a conflict issue somewhere.
View 4 Replies
View Related
Mar 16, 2012
I have a MI-FI dongle which i use to connect to the internet (small wireless router) It does not support a wireless printer though. So I figured IU would use the old BT Home hub I had to connect my computer and the printer.
This worked for a few minuites untill the computer decided that the home hub should be dominent and instead of accesing the internet the browser would show the bt cannot conect to the internet page.
View 1 Replies
View Related
Nov 5, 2012
I have a pc that is connected to my router through an Ethernet cable. The network sharing center confirms I am connected to my network, and that I am connected to the internet; however, I can not connect to the internet with IE, chrome, or any other internet-based application. The icon in the bottom right also says I have internet access. As well, another ethernet-connected PC in the house works just fine, and my laptop has no trouble connecting through the wireless. I have switched the connection ports on the router between the two PCs and the problem still persists.Trouble shooter results without identifying any problems and trying to "set up a new connection or network" says "you are already connected to the internet". This issue occurred over night and had been working for over a year without issue. I have restarted the router as well as the pc, connected to the router and it shows the pc as "inactive"
View 10 Replies
View Related
Jun 14, 2012
Few days ago my people from my ISP installed a router in my house, now it's a D-Link DIR-100 router which they configured themselves and then left. Thing is I have never had a router before so I don't know first thing about them.My current problem is that I want to simultaneously connect another pc to the router, without having to turn one of the pcs off, but they don't seem to be working at the same time, I am guessing it's because of the IP conflict, both pcs had the same IP. I thought I would take a look at the routers web interface but was unable to connect to the default address mentioned in the guide (192.168.0.1), after some googling I tried every kind of variation of the IP addresses, including default gateway (which is different) and whatnot, but still unable to connect. I don't get a timed out, just immediately get the "Unable to connect" error. So I am wondering, if there is a way to either fix the IP conflict without accessing the interface, or how to access the interface and then how to fix the conflict. [code]
View 13 Replies
View Related
Dec 8, 2011
I have a Netgear N router that worked fine with our old modem we recently revamped our modem to the Motorola Surfboard Extreme and it won't allow the router to connect to the internet.
View 1 Replies
View Related
Oct 13, 2012
My husband has an Acer Aspire 5720-4126. Last month I bought a Netgear wireless router (model WNDR4500) and he is the only one in the house that can't connect to the internet. He is able to get to the router, excellent strength, but the Activity has Bytes: Sent-3,142 Received-0. I had the Netgear customer service tech try with no results. [code]
View 7 Replies
View Related
Nov 26, 2011
I have a Linksys wireless router. Currently, a PC is connected by cable to it. Also connected by cable are the PS3 and stand-alone printer. It seems when the PC is shut down there's no Internet access to through the router. Whether the PC is up or down shouldn't effect the router, right?
View 1 Replies
View Related
Nov 30, 2012
OS: WIN XP ?For some reason I am not able to access the internet even though I'm connected to the corporate router. When I do an ipconfig /all the Connection-specific DNS Suffix is missing. Not sure if that is part of the issue. I tried ipconfig /release and ipconfig /renew and that did not resolve the issue.Another odd thing is when someone else logs into my computer they are able to access the internet through the corporate wifi.
View 1 Replies
View Related
Jun 19, 2011
Currently I'm living in a dorm. The house has wireless network. But WEP encryption is used to secure it. I know this method is not safe. Also since there are many people are living in the house i don't want my computers be connected to this network.What i want to do is to setup my own network. I bought a NetGear DGND3300 router. I setup a WPA2 protected wireless network. I can connect all my devices to this network but naturally this way i have no Internet access.Is there a way to use Internet access of the house's router but still keep my local traffic not seen by anybody else
View 2 Replies
View Related
Nov 24, 2011
Orange sent me a replacement Netgear DNG1000 and from the moment I had it there was issues, if N mode was enabled and I had to set it to B/G only for it to have a stable connection, not a problem as I only use it for the internet. The range on it was roughly the same as the livebox. For a few weeks it worked fine until recently it started to go insane, on the main computer the wifi works most of the time with 80%-95% signal strength, and then every now and then it will suddenly lose communication with the router but act as if it was connected for 5-10 minutes, signal strength is still at about 90% yet I can't access the router or the internet. Wifi works fine at full speed on the stairs, drops to a few bytes per second on the landing and then increases back up to full speed in the room next to it. In the one bedroom the wifi works up until the door where it instantly drops from full speed to a few bytes a second. This drop off point is only a few cms, as in full speed at one place, move it back a few cm and it slows down loads, but I still get 4-5 bars on windows and -50 RSSI on inSSIDer, about 94% strength and a link quality which tends to fluctuate. What could be causing this, specifically the weird instant deadzones and randomly not responding.
View 1 Replies
View Related
Sep 17, 2011
I have a Toshiba Satellite P205-S6267 that will not access the internet via a router (Netgear or Verizon). My system sees the router, but will not go onto the internet without connecting the laptop to router.Netgear support could not resolve so I returned the router. I switched to Verizon FIOS and the technician encountered the same problem with the Verizon router that I had with the Netgear router
View 18 Replies
View Related
Nov 21, 2012
has a netbook which on this one, the network is not working. He connects to the wireless router and gets an ip but he does not have access to the internet.When I tried the netbook at my house with my wireless, it worked perfectly and it stopped working again on my friend's network.
View 7 Replies
View Related
Jul 23, 2012
I am able to connect to TPlink router through my pc but unable to access internet.The router is unable to detect dynamic ip.
View 1 Replies
View Related
Oct 20, 2012
I have High Speed Charter Internet going to a modem in form of coaxial cable with one Ethernet port available and one coaxial connection for TV and a phone jack. I have that Ethernet port connected to a:Motorola Wireless Modem[CODE]
View 4 Replies
View Related
Aug 4, 2011
I've reset the tcp/ip protocols but still im connected to the router but cant access internet I have the latest drivers for my network adapter. I am using windows 7 starter edition.
View 1 Replies
View Related
Feb 8, 2012
Im trying to set up a wireless router in my dorm room. I know, I am not supposed to do that. I got it set up and everything, but still didn't have internet access.
View 1 Replies
View Related
Jan 30, 2013
I have two routers on my local network:
1. ADSL Wi-Fi router provided by my ISP. This is the primary router for my network which is connected to the internet. Router IP: 192.168.1.1 (DHCP enabled)
2. TP-Link wireless router which is connected to the primary router through its LAN port (not WAN) with its DHCP turned off. So I'm using this router ONLY to extend the network to another area. This is a 3G enabled router. Router IP: 192.168.1.2
There are two different wireless SSIDs but basically only ONE network (all the PCs connected through any of the two routers are on the same subnet and have same IP range i.e. 192.168.1.x). I want to use the 3G internet connection through the secondary router when the ADSL connection is down. Whenever the ADSL connection is down, I would just connect the 3G-USB to the secondary router, all the computers on the network should connect to the internet while skipping their route through the primary router WITHOUT CHANGING ANY SETTINGS. Is it possible? Do I need to modify the routing tables? Or is it possible by configuring the DHCP server to assign the primary DNS address as 192.168.1.1 and secondary DNS address as 192.168.1.2?
View 11 Replies
View Related
Jan 7, 2013
I am having a problem in setting up my Router. Its "TP-LINK WR 720N". I have a LAN connection in the main PC and a further dialer like thing with user name and password is executed to access the internet. Each of the customers have diff IDs and passwords based on the bandwidth of the connection. The problem is that first am i connecting the Router in the right way? I put the main LAN cable into the Router's WAN port and the Other Ethernet wire i put is that from PC's Lan port to Router's LAn port. Is this right? I am confused because in the guide a modem is also mentined and i think thats for DSL users...
If i use the above settings, my LAN gets connected and the dialer also works and gets connected but when i access the internet from it, that doesn't work and no webpage opens.
Similarly, the Wireless connetion is displayed in the Laptop and when i access it, it gets connected, but it has a yellow exclamation mark in it, and the same goes here that the internet does not work. My internet connection id fine because i am sing internet no using main Lan ports of Pc, so i guess the problem i s with my Settings...
View 2 Replies
View Related
