Is anybody deploying ASA Services Module? I am looking for feedback/gotchas/advice for a migration from an ASA-5550 HA pair.I also received confirmation from Cisco that VPN termination is active in the latest 8.5/8.6 code releases, so hopefully should be able to fully retire my 5550's.
I've got tons of fibre in my network. However, tbh, my knowledge about correct light levels isn't great. I generally wait until my router complains about a light level before I do anything. I would like to set up SNMP monitoring for light levels, but I need some kind of baseline.Anyone with extensive fibre experience? What light levels should I be looking at for both multimode and singlemode fibre?
I need setting my 825 router on the best optimize setting for my ps3, Im running wireless on it and the router is about one room away from my ps3 which isnt that big of a difference since I am getting 95-100% signal on it, the issue is the rate speed runs about 36m-54m it NEVER, or at least I havent seen it go higher than that.I turned the QO6 engine but it didnt really change a thing, will running this wire do the majic? or is there another alternative set up I can do on the router to have it run on best settings.
I really am having troubling with my current router wrt120n and it is a dumb router that doesn't even know how to prioritize clients. A low priority client can still lag my gaming experience cause someone in my house is streaming videos. I need a router that isn't dumb and know how to prioritize connections and doesn't destroy my gaming experience.What would be the bestest gaming router out there?
what options are available to a customer with 800 APs that is finally migrating to a centralised model and therefore migrating from WLSE to WCS? Assuming that they move to v8 of WCS can they upgrade their WLSE licenses to WCS?
Are there any methods for statistic data importing from old LMS 3.2 to a new LMS 3.1 version? I know about devices invemtory export/import function, but also i want to save all data gathered from previous time.
I have an ACS 5.2 deployment and i want to upgrade it to 5.4 version.I have 2 server in my deplyement:
1/ Primary Server as Authentication server & log collector
2/ Secondary server as Authentication server.
What is the best way to do the migration? Normaly, i can proceed as follows:
1/ Deregidter each server from the deployement ==> Make both the servers standaone 2/ Upgrade the Secondary server. 3/ Upgrade the Primary server (without migrate the log server). 4/ Join Servers to the deployement.
I need to upgrade my ACS for windows 18.104.22.168 to 5.2 as we have come across the windows 2008R2 AD problem. Now reading the migration document it says I need to go to at least 22.214.171.124 first which will not be a problem, then I need a migation server, so that means I need another ACS server as the migration server. As I already have 2 ACS servers could I use one of them as the Migration server, ie take it out of production?
I am working on a migration from Windows based WCS 126.96.36.199 to NCS appliance (1.2.1-once it is available). After stopping WCS, I issued the export userdata C:WCS07Migrate. The process completed, but did not create a single zip file. I found 2 files created in the tmp directory.
One contains multiple a folder called tempDirUserDataFromDb - containing multiple xml files; and another file called ImportExport_ca<number> which contains the maps. Was there something incorrect in my command? Can I use still use these files on NCS? Or do I need to redo the export on the WCS?
NCM is going away. It is recommend to move to LMS. We already have a LMS deployment. Currently just used for Monitoring/Performance.Trying to figure out how to get the Configuration change piece that we used NCM for into LMS. Not really having any luck.What I am really wanting to do is configuration archive, device config change notices (when a device config changes I can run report to see who and what was changed), and configuration comparisions (between old and new configs)
I need to Migrate from ACC 4.1(1) to ACS 5.4, Have configured Network Access Restrictions and Networks Access profiles in ACS 4.1(1), can i go for staright away migration and is the same supported in ACS 5.4
I'm trying to get all the templates and Maps I've created in WCS into our new NCS. The instructions say just run the export.bat file on WCS and then Migrate into NCS. I cannot find any export.bat file on version 188.8.131.52 of WCS. Is it only available in WCS version 184.108.40.206 ro 220.127.116.11? Do I have to use the export.bat file or can I just do a regular backup and restore?
A customer is asking to upgrade their LMS 3.0 to Prime 1.1. However, the customer or their previous system's integrator never actually installed LMS 3.0. The licensing and PAK were never used as well. My question is, can I still use the migration top level part # R-PI-1.1-UP-K9 to upgrade LMS 3.0 to Prime 1.1 because there was no licensing ever installed? How would the migration of the current licensing work with the new licensing PAK if that is the case? Or does the customer have to purchase a fresh Prime 1.1 licensing (top level part # R-PI-1.1-K9) because LMS 3.0 was never installed?
We have a single 4404 that was setup long before I arrived with Guest networks that timeout and other such tweaks. Is there a document somewhere that shows a way to migrate the old settings to a new 5508 that we are purchasing? By the time the 5508 arrives I will have a very small window to setup the unit before a new wing goes live. I need the new unit as we have reached our limit of licensed AP's on the old 4404. It seems like everyone keeps talking about an easy way but no one says how to do it.
I have never setup one of these units before from scratch so I don't know how long it will take.
I have old ASA with 8.0 configuration that includes huge number of ACL, NAT , VPNs , we got a new ASA with 8.6 , and we are planning to move the configuration to the new box , I'm wondering what is the best approach to do this , I'm thinking of one of the following scenarios1- downgrade the new ASA to 8.3 , the apply the config , remove the identity nat commands and names then upgrade to 8.6 and after that reconfigure the NAT rules and object groups .2- convert the old config manually to 8.6 code including NAT , object-group ,ACL and apply it to the new ASA ( this is going to be huge task). What are the commands that I have to look at when I convert to 8.6 and will the VPN configuration be affected ?
WCS 7.0 to Prime Infrastructure 1.2 migration?I am so confused on the migration procedure as I found the documents in Cisco kind of contradictory.Some document said it is required to upgrade WCS to NCS 1.1 before to go to prime infrastructure 1.2.And the other document said WCS can directly upgrade to prime infrastructure 1.2.
my company has the asa 5505 working as the remote access vpn server. my company needs more licenses for vpn than the asa 5505 give it. because of my company purchased the asa 5510. i must migrate configuration from the asa 5505 to the asa 5510. i exported configuration file from asa 5505. i made the changes on them and imported them in the asa 5510. my asa5510 doesn't work. i putted configuration files from asa 5505 and 5510.
Have upgraded WCS to 7.0 due to a Mesh network feature we needed, but now see I can no longer edit the AP migration templates. The interface allows me to create or delete them but the command dropdown box does not show an Edit option. So now for every AP I want to migrate I need to create a new template before I can select the AP's and migrate them. I still need to migrate about 220 APs....
Looking though the function it tells me to click on the Migration Template name. However neither in MS IE nor Firefox this works, there is no link activated.
I have done a WCS 18.104.22.168 to NCS migration prior to moving to Prime 1.2. I followed the instructions to export the WCS database via the export.bat all command and exported the database. However, when I import this zip fileto NCS there do not seem to be any of the original WCS templates. All the maps and AP details have migrated but no templates.
I have tried the export again and ploughed through the resultant zip file looking for anything that looks like template files but there is nothing immediately apparent that looks like templates.
I'm planning migration from ACS 3.3 to a new machine, so I'm thinking about new Cisco ISE.I have the following question: ACS 3.3 acts as AAA RADIUS with LDAP repositoriy for wireless deployment, using PEAP-GTC. Is possible, with ISE, to use a different EAP method, such as PEAP-MsCHAPv2 or EAP-TTLS?
In ACS 5.X I think it's only supported PEAP-GTC and EAP-TLS when identity repository is LDAP. Is the same in Cisco ISE?
I see the WS-SVC-AGM-1-K9 was EOL Jan 2010 ,What is the suggested Product Migration Option? Also if any is using this WS-SVC-AGM-1-K9 I would like some feedback ,Our problem is listed below and we are wondering of the WS-SVC-AGM-1-K9 will work ?
Looking at the best option to detect attempts at cracking our SIP servers. We see connections from scanners on the internet trying to brute force SIP passwords reasonably often, and would like to be alerted to them happening. Essentially we see hundreds of SIP registration attempts or Invites from the same IP, and this is how we know it is dodgy.