Cisco :: Can't Access ASA's IPS Module
Jan 19, 2011
I'm having trouble connecting to my IPS module via ASDM and web browser after configuring an IP address for the IPS module via CLI.The 5510's management port is plugged into our switch, and a VLAN is assigned at the switchport. I gave the IPS module an IP address in the same subnet (DG as well) as the 5510's management port, assuming the IPS module would communicate over the 5510's management port. Is this not right? I'm limited to the CLI for now, and would really like to access the IPS module through the ASDM.
View 6 Replies
ADVERTISEMENT
Jun 16, 2011
I try to access to WS-SVC-NAM-2 module in the Switch 6509. But is not work although the HTTP port is enabled (I tested with the command telnet @ip 80).
I try telnet access to the module to check the config , but I always the message that the lo gin / password is wrong even though they are valid.
View 4 Replies
View Related
Nov 4, 2012
In our Environment we used to Connect to wifi using Radius Authentication Through AD Account (Encryption: TKIP and CIpher, Authentication Open+EAP and Network EAP, Key management WPA) this settings which will be done And pushed through AD Itself.We Use CIsco 1130AG, 1200 Series in most of the areas which have no Issues.But We Have Some trouble with Cisco WAP4410N Access point.In This Access point users were not able to Connect to wifi through Radius Authentication.However users were able to Connect to these Access point, but it is unsecured, whoever configure's the correct client settings in their PC. They can connect to SSID. This Access point is capable of supporting Radius Authentication?
View 4 Replies
View Related
Aug 13, 2011
I am proposing Remote access VPN solution to my client as per the attached diagram. However they are required IPS solution as well.
So in this case i dont think i can implement the IPS with outside interface in inline mode because of the encrypted traffic. Is it feasible if i enable IPS with inside interfce ?
View 1 Replies
View Related
Oct 23, 2012
I noticed that the 3600 access point series will get an add-on module to support 802.11ac. This standard will support more than 1 GBit/s.But the 3600 series still do only have got one GBit port. Any extended information about 802.11ac in the upcoming Cisco portfolio?
View 8 Replies
View Related
Apr 3, 2013
Is 802.11ac wireless module for Cisco Access Point 3602 is available to order ? what Wireless controller we need to use for the support of 802.11ac wireless standard ?802.11ac will support only on 5700 series wireless controller ? Or it will support with 5508 Series also ?
View 7 Replies
View Related
Aug 23, 2012
i bought new RF Cisco 7204VXR NPE-G1. As soon i enable OC3 module ( PA-POS-OC3SMI) CPU of the router shoot to 100%, and if i reboot the router, it wont comeback not even on Console. I had to remove the POS card and then boot router and then hot insert the module.
so i put the command
int pos 4/0
loopback internal
as soon igave this command, CPU dropped down to normal. Whats the deal here? now i need to activate the circuit on this POS interface, but as soon i remove loopback internal command , CPU shoots to 100% Although CPU sorted dont show any process causing it.
[Code]....
View 1 Replies
View Related
Apr 9, 2013
I want to add module of WS-X6716-10GE(-3C). The type of 6500 isCisco WS-c6509-e (r7000) processor (revision 1.2).Can I add this module to this type of 6500?Do I need to reset the 6500 in order to the 6500 receive the module?
View 2 Replies
View Related
Jan 25, 2011
I have the situation with my new Cisco 2951 router. It has only one module on board - SM-D-ES3-48-P. I don't know what is wrong but I can't see any information about this module. When I connect my laptop to any port it's become green, but it's still green even after I disconnect PC from this port. Sh ip int brief command shows only built-in gigabit interfaces. I also connect my second PC to the router by console to monitor any changes when I connect or disconnect laptop to the module's ports. [code]
View 3 Replies
View Related
Oct 31, 2011
Will Cisco LMS Prime 4.1 be getting a map module, so you are able to see a graphical map of up and down status of devices? I know the topology map is a module within LMS, but what would be nice to see is a graphical map, where you are able to manipulate the icons to place them on that status map.
View 2 Replies
View Related
Oct 9, 2012
Wat will be the default memory and hard disk for SM-SRE-710-K9 and wat will be the maximum support for this module.
View 1 Replies
View Related
Apr 8, 2013
I have cluster of firewalls which inclueds AIP module and are in production. Due to some issue modules could not be activated. Now I need to activate and udate signature of them. So whether I can do all this activity without effecting my production (Zero downtime).
View 5 Replies
View Related
Jun 28, 2012
I know to add a user in the service engine is (config)#user Aileen create but how would you remove it. I tried no before user to negate the command but i do #sh users and the username is still listed.
View 1 Replies
View Related
Mar 11, 2013
I have a Hwic 3G-GSM module in an 1841 router. The sim card in the module is configured on an APN no username and password. I have checked all the config from a working router 1841 plus the same module and same vendor Sim card on the APN and all is working. I have configured the second router but it doesn't want to connect at all. If i put the Sim card in a standard 3G modem life is good, and I can connect to the APN and get the static IP address. When I'm trying to initiate the connection from the 1841 the Sim card wont connect.
My config to debug:
sh ip int brief
Interface IP-Address OK? Method Status Protocol
FastEthernet0/0 10.20.20.1 YES NVRAM up up
FastEthernet0/1 unassigned YES NVRAM up up
Cellular0/1/0 unassigned YES NVRAM up up
NVI0 10.20.20.1 YES unset up up
[ code] ...........
I'm not sure if the cellular card is calling the wrong script (d0efault-d0ials0crip) instead of the gsm one configured.
View 5 Replies
View Related
Dec 19, 2011
We have a cisco 7204 VXR and would like to know the module which has two fastethernet port. We tried a PA-2FEISL-TX but it did not work.
View 1 Replies
View Related
Jan 28, 2011
I have Cisco ASA 5510 with CSC-SSM-10. ASA anti-virus service can not update the Base and Plus lisense. No Activation Code required for renewal. I go to "Administration> Product License" in the CSC SSM console and click "Check Status Online" to get the latest expiration date.In the module on the Check Status Online has reported the following error when: Base License status could not be checked because of a license server failure. "Please try again later", "Plus License status could not be checked because of a license server failure. Please try again later". UPDATE manual virus database can be seen in the latest available version, can not be upgraded because the service expired.
View 2 Replies
View Related
Mar 26, 2011
if the 7600-SIP-200 supported in VSS mode or not ?
I have configured to Cisco Catalyst 6513 as VSS, both of them have the 7600-SIP-200 module, before converting them to VSS I was able to work with the 7600-SIP-200 module, but after I did convert them to VSS, both modules didn't work.
here is the show module output, after VSS conversion:
VSS1#show module Mod Ports Card Type Model Serial No.--- ----- -------------------------------------- ------------------ ----------- 1 0 4-subslot SPA Interface Processor-200 7600-SIP-200 JAE14500GMT 7 5 Supervisor Engine 720 10GE
[Code].....
View 1 Replies
View Related
Feb 14, 2012
how to show all the module on the ASR 1004?
View 4 Replies
View Related
Nov 15, 2011
Does the ASR-1000 accept an HWIC module, or must one go to a SIP/SPA for all modules?
View 1 Replies
View Related
Feb 7, 2011
For some test in my lab , I ordered on e-bay a AIM-VPN board , they guy told me that it work in a C1841.When I compare to the one I have in my C2621 , they look equal.On both pcb I can read : CN6I280AAA
View 3 Replies
View Related
Jun 2, 2013
We have installed 5585-x in active/active mode with transparent firewall. We have created two virtual sersors for vs1 and vs2 in IPS module and linked with ASA context C1(vs1), C2(vs2) and admin(vs0).
As firewall is working in transparent mode, we have bridge IP address for context C1 10.1.1.1 and for context C2 10.2.2.1.
I have added default routed for context C1 10.1.1.2 .It is in the outside of asa and SVI on switch.For the other context C2 10.2.2.2.
IP address range for the IPS module and what should be the gateway for IPS module.AS the traffic is coming from outside and going to inside interface of ASA.
View 1 Replies
View Related
May 20, 2012
What module is used to push configurations in LMS 3.2.1?
View 1 Replies
View Related
Oct 11, 2011
I have checked on Cisco.com and as per a module support document for ISR's G2, the NM-1CE1TI-PRI module is not supported on new ISR's.
Grateful if more clarification could be obtained about the above.
Will be router not detect the module when inserted in the chassis?
View 2 Replies
View Related
Mar 7, 2012
We want to implement HSRP between two 3945 ISRs:
RouterModelIOSModuleR1Cisco 3945 Integrated Service
Routerc3900-universalk9-mz.SPA.151-1.T.binNME-AIR-WLC12-K9
R2Cisco 3945 Integrated Service
Routerc3900-universalk9-mz.SPA.151-4.M1.binNME-AIR-WLC25-K9
The issue that we are experimenting is that, although the module's interfaces are up and HSRP in correctly configured, the show standby summary displays that the Active router is local in both routers. We also have some GigabitEthernet in the routers and they are correctly running HSRP. Does the WLC Modules physically support HSRP?
View 1 Replies
View Related
Feb 13, 2013
how to enable the SFP module on cisco 2921?
View 3 Replies
View Related
Mar 24, 2011
I am using an ASA5510 and I would like integrate the CSC SSM module in it. What is the Process to upgrade, is it possible and Where I can find it ?
View 1 Replies
View Related
Apr 29, 2011
I have 2611xm router with 2 fastethernet ports. Now I want to install NM-1FX-TX module. I just want to conform that does 2611 supports NM-1FX-TX module. I am using this device for lab purpose. I am using latest IOS"
View 2 Replies
View Related
Sep 1, 2011
I recently installed the license ACE-SSL-05K-K9 on ACE10 with multicontext solution.The license provides 5000 Maximum number of SSL transactions per second (TPS).The customer would like to track this to find out the correct size and in the case of services https upgrade licenses.Can I do it so through particular output or it's necessary monitoring with snmp service? In the second case, can you tell me the oid string to use?
In case the module should receive a higher number of connections to that provided by the license, what's the issue for new https connections?
View 3 Replies
View Related
Jun 19, 2012
i just configured GRE over IPSEC on my Cisco 3745 router with VPN module installed. As soon i hit 25Mbps traffic, my CPU is touching 80%.
What maximum Traffic 3745 with GRE over IPSEC it can support?
Also show process CPU sorted dont show any evidence of which process eating it up.
sh processes cpu sorted
CPU utilization for five seconds: 75%/75%; one minute: 77%; five minutes: 78%
PID Runtime(ms) Invoked uSecs 5Sec 1Min 5Min TTY Process
[Code].....
View 3 Replies
View Related
Oct 1, 2012
I have a couple of ASA 5510 firewalls configured and working. I'm now charged with configuring the IPS modules. I'm having to do this remotely. Since the IPS module hasn't been configured I'm guessing it's on 192.168.1.2 with the default username/password.
I'm told that the workstation I access from connects through a switch to the ASA and to the IPS.
I've set the ASA management port to 192.168.1.1. I can't ping 192.168.1.2 - not sure I'm supposed to be able to. In the ASDM, Configure IPS prompts for an IP address. Entering 192.168.1.2 returns "IP address of the management port is unreachable".
View 4 Replies
View Related
Aug 19, 2011
I have a question about upgrade NAC Module, I follow standalone procedure to do the upgrade but I wonder about the upgrade file should I use because on the Cisco site I didn't find the upgrade file from 4.8.0 to 4.8.2.
what I found is nme-nac-upgrade-4.8_2-from-4.6.x.tar.gz ??!!!
So my question If I use the NAC upgrade file I was used for upgrade the CAM & CAS applaiances
View 2 Replies
View Related
Jul 5, 2012
How can I update the expired certificate in AIP-SSM-10 Module using CLI or ASDM.....Here;s the output from the device....and also is there a way I can generate some daily or weekly reports in a graphs.
edge-s2# show versionApplication Partition:
Cisco Intrusion Prevention System, Version 7.0(2)E4
Host: Realm Keys key1.0Signature Definition:Signature Update
[Code].....
View 1 Replies
View Related
Feb 16, 2010
We are using a Ace module running version 3.0?We do have a service which can now be reached by a url like https://www.xxx.com/yyy/ < notice the last /This is running via the Ace which terminates SSL and so on..
So now our client wants an url like https://www.yyy.com . The backend realservers and place of virtual dirs on IIS stays the same.
So now /yyy/ needs to be added to the backend realserver request, so the correct virtual dir is used. Therfore I need to add this Uri towards the realserver.
View 4 Replies
View Related
