Will Cisco LMS Prime 4.1 be getting a map module, so you are able to see a graphical map of up and down status of devices? I know the topology map is a module within LMS, but what would be nice to see is a graphical map, where you are able to manipulate the icons to place them on that status map.
View 2 RepliesI would like to know if WS-X6848-SFP modules are supported with LMS Prime 4.1 and 4.2.
View 2 Replies View Relatedjust found that on [URL], it stated that Cisco ASR 1000's management tool is Cisco Prime Network Analysis Module, which is same name as software that can be install in SRE of Cisco ISR G2 router for network analysis via web browser.
My question here is this mean Cisco ASR 1000 has built-in support for Cisco Prime Network Analysis Module, which has similar function as the one on Cisco ISR G2 router's SRE?
I'm currently running CiscoWorks LMS 4.0.1 on Windows 2003 under VMware and just got upgrade licensing for Prime Infrastructure 1.2. I am assuming that I will need to upgrade the current server to Prime LMS 4.2 in order to ensure that data migration to Prime Infrastructure goes well. I am planning to follow Cisco's recommendation to run Prime LMS and Prime Infrastructure in parallel for a time and migrate individual functions.
My real question is about Syslog handling. All of the managed devices are currently sending Syslog data to LMS. As a last step in the migration, is it possible to change the IP address of the Prime Infrastructure server to replace the Prime LMS server so that the Prime Infrastructure server will just start getting all the Syslog data, or do I need to go change hundreds of managed devices to point to a new address?
What is the relation between: cisco NCScisco Prime LMSCisco Prime infrastructure.As i orderd a Cisco Prime infrastructure from a Cisco Partner and what i got is :
x2 cisco NCS appliances
x1 DVD cisco prime infrastructure
x1 DVD Cisco prime 4.2
I recently installed LMS 4.2 appliance and I noticed that the web administration page was really slow. I checked the CPU utilization in VMware and it was at 55%.
View 1 Replies View RelatedI am using Prime LMS 4.2.2 software to archive configuration for my cisco Network Device switch and firewall . All works fine except for two new Cisco ASA 5525 and ASA 5545 ( Software Version 8.6.1.2 ) . I have already checked credential , ssh access , snmp configuration and all seem correct. But Archive configuration job end with failure. This is the error message:
View 1 Replies View RelatedMy customer is using Cisco Works LMS 4.0 ( Product # : CWLMS-4.0-300-K9 ) and we they are willing to upgrade it to Cisco Prime LMS 4.2 (or latest version). as well as adding additional device licenses to become 750
View 1 Replies View Relatedhave bought license for LMS 4.0. I want to upgrade to 4.1. Should i buy any additional PAK for the license upgrade?
View 1 Replies View RelatedHow do I add the MSE 7.4 VM to Prime 1.3.20?
The Prime uses https or http when trying to add the MSE. But those ports are closed on the MSE. The MSE seems to expect traffic on tcp 8001.
We did not change the default NCS-username/password in the startup-wizard.
C:WindowsSystem32>nmap 192.168.0.211
22/tcp open ssh1099/tcp open rmiregistry1521/tcp open oracle8001/tcp open vcom-tunnel9001/tcp open tor-orport9002/tcp open dynamid
[Code]......
Is it better to uninstall LMS 4.0 completely and then install LMS 4.2 or could I do a direct upgrade?. I've heard the db tables etc. have changed a lot and might cause problems for a direct upgrade.
View 5 Replies View RelatedI am trying to populate the LMS 4.1 components to ACS.
View 2 Replies View RelatedI am currently running NCS 1.1.1.24 and trying to upgrade to prime 1.3, but running into some issues, i applied the patch ncs_patch-1.1.1.24-upgrade-12.tar.gz, but when i try to acutally upgrade i get the following...
admin# application upgrade PI-upgrade-bundle-1.3.0.20.tar.gz defaultRepo
Save the current ADE-OS running configuration? (yes/no) [yes] ?
Generating configuration...
Saved the ADE-OS running configuration to startup successfully (code)
Is there anyway to migrate off of WCS to Prime NCS? We have a fully built WCS system with maps and all configs and was wondering if there was a way to restore to NCS.
View 1 Replies View Related[URL] it mentions that migrating from NCS 1.1.2 to CPI 1.2 isn't possible.
How can I get around this?
A customer is asking to upgrade their LMS 3.0 to Prime 1.1. However, the customer or their previous system's integrator never actually installed LMS 3.0. The licensing and PAK were never used as well. My question is, can I still use the migration top level part # R-PI-1.1-UP-K9 to upgrade LMS 3.0 to Prime 1.1 because there was no licensing ever installed? How would the migration of the current licensing work with the new licensing PAK if that is the case? Or does the customer have to purchase a fresh Prime 1.1 licensing (top level part # R-PI-1.1-K9) because LMS 3.0 was never installed?
View 2 Replies View RelatedAfter update to LMS 4.2.3 is get always a message to confirm when login:
"Server is capable for performance tuning. Please enable PTT ...."
Even when i setup PTT the message will come again next time i login.The message comes also several times after login.where to disable this message?
I'm trying to migrate old data from WCS 7.0 to Prime 1.2 ... I have already created the zip file from WCS and imported it into the defaultRepo on Prime. I see it in the directory when I do a show repository defaultRepo so I have confirmed that it is there. My issue is that it appears Prime 1.2.1.012 won't accept the cli command of ncs migrate.
how I can proceed with the migration? I haven't been able to find any similar command in the Prime CLI so at this point I'm lost as to where I should go from here. I really don't want to have to tell the customer they have to downgrade to Prime 1.1 in order for them to perserve their maps especially since the Deployment Guide for Prime Infrastructure states that it is possible to migrate date from WCS 7.0 to Prime 1.2 as shown below ...
Data Migration
#
Data can be migrated from WCS 7.0, NCS 1.1, or LMS 4.x. More details on migrating data from each of these applications are spelled out in the following sections.
[Code].....
possible in Cisco Prime 4.2, to kick off a particular user? in GUI or CLI ?
View 0 Replies View Relatedmy customer is using Cisco Prime 4.1 as an Upgrade from LMS 4.0 and has made a discovery of a new added Cat 4506E with a Sup 7E and Modules.All the devices have been discovered, excepted the module WS-X4712-SFP+E.Is this card not supported yet ?I could not find any detailled and actual information about the support or not of this module, or about the conditions for the Module support it in Prime 4.1..How ist it possible to proceed to having this module discovered ?
View 1 Replies View RelatedWe have installed the Cisco Prime LMS 4.1 in our production environment. We have configured SMTP settings, but unable to find where we can configure username and password for SMTP authentication. It's only giving a option to enter email address without any authentication parameters.
View 2 Replies View RelatedWhen I run installation process I have received unexpected error:I have windows 2008 R2 x64. Antivirus is disabled and I have administrator privilege.
View 6 Replies View RelatedWCS 7.0 to Prime Infrastructure 1.2 migration?I am so confused on the migration procedure as I found the documents in Cisco kind of contradictory.Some document said it is required to upgrade WCS to NCS 1.1 before to go to prime infrastructure 1.2.And the other document said WCS can directly upgrade to prime infrastructure 1.2.
View 13 Replies View RelatedWe've an issue with authorization on NCS system. NCS successfully integrated witch ACS, but there is a problem with one user. All users have equivalent rights under root. There is shell profile with all possible tasks (exported from NCS server) configured on ACS. All users exept this one (unlucky one:)) authorizes successfully. In ACS logs, authentification and authorization status for this user is passed and all attributes (policy, profile, AV-pairs e.t.c.) is the same as for another users. This 'unlucky' user gets a following message: There is surely no browser or network issue. Tried from different PCs with same result. There is no any local info related to this username on the NCS server. When i change one charecter in the username on his ACS account, everything works well.
Our ACS v
Version 5.1.0.44.X
And NCS
Version : 1.1.2.X
I have just started my installation of Prime 1.2. I have the OVA loaded (NCS-APL.1.2.1.12-K9) and I went through all of the setup. I have the webpage loaded but unable to get past the Root login. I then tried to change the password using the "ncs password root password password" command but get the error message "Execution failed: Cannot find user: root". I have seen some people talking about the wrong OVA file but that was for Version 1.1 I think.
View 1 Replies View Relatedwe installed a new CPI 1.3. Both machines are in the same subnet and close to each other. Everything looks fine and is installed as we see in the config guide.When we halt the VM of the primary Server, the backup takes over but with errors. I'm also not able to login! [code] my colleauges did the same a few days ago also with problems or similar problems and restore the server from backup.
View 2 Replies View RelatedI´m about to upgrade a customers appliance box to PI 1.3. I am guessing an upgrade to 1.2 would be almost the same, license wise.
View 10 Replies View RelatedI have Prime 4.1 on windows with the latest update, it is up and running except for few devices ASR903 routers that are not being recognized in the Fault (DFM). These devices are supported in this release, The fault is showing that the devices are stuck at 10% learning state. The strange issue is that when i click on the routers that are in the learning state some shows in the device type as N/A ans others are showing "routers". Anyway i followed the steps mentioned in "How can I troubleshoot device discovery stuck at 10%"
View 1 Replies View RelatedWe have Cisco Prime 4.2 installed Windows 2008 R2 server, I am facing problem when I am going under Report>Fault & events or any other section, the browser gets stuck in loading page and become unresponsive. If I restrart the Daemon manager service it works fine for some time and again start giving problem in two or three hours time interval.I also face the same problem when I go to Admin > Job browser window.Does any one face the same problem,I have changed the host name of thserver using script and also generated new SSL certificate and I tried with diffrent browsers but problem is still persisting.
View 1 Replies View RelatedI am proposing the Cisco Prime LMS 4.1 (i.e LMS-4.1-500-K9); Do I need to add the HUM license for monitoring or does that come inbuilt?
View 1 Replies View Relatedwe are installing cisco Prime NCS 1.1 and we are facing some issue for License.
I would like to clarrify the below licneses.
L-WCS-NCS1-M-K9
L-PINCS11-300-U
L-PINCSW11-300-U
I recently upgraded from WCS 7 to Cisco Prime Infrastructure 1.3 (1.3.0.20). I've successfully added my 5508 WLC, 7204 router, 4506 Switch and several other devices. The one problem I have not figured out is how to add my 50 + AIR-LAP1142N-A-K9 to Prime. I can see under Home > General > Overview that I have AP availability of: 53 but when I go to Device Group > ... > Unified AP > Cisco 1140 Series Unified Access Points there are no devices listed. I've tried to manually add them but they fail.
View 6 Replies View RelatedJust downloaded the Eval copy of Cisco Prime 1.2.
Wondering if I can run this under a VMware Player instead of loading it on a UCS server?
If yes, is there a recommended version of player?