Cisco WAN :: 1841 - 3G-GSM Module Not Connecting APN
Mar 11, 2013
I have a Hwic 3G-GSM module in an 1841 router. The sim card in the module is configured on an APN no username and password. I have checked all the config from a working router 1841 plus the same module and same vendor Sim card on the APN and all is working. I have configured the second router but it doesn't want to connect at all. If i put the Sim card in a standard 3G modem life is good, and I can connect to the APN and get the static IP address. When I'm trying to initiate the connection from the 1841 the Sim card wont connect.
My config to debug:
sh ip int brief
Interface IP-Address OK? Method Status Protocol
FastEthernet0/0 10.20.20.1 YES NVRAM up up
FastEthernet0/1 unassigned YES NVRAM up up
Cellular0/1/0 unassigned YES NVRAM up up
NVI0 10.20.20.1 YES unset up up
[ code] ...........
I'm not sure if the cellular card is calling the wrong script (d0efault-d0ials0crip) instead of the gsm one configured.
View 5 Replies
ADVERTISEMENT
Aug 16, 2011
I only know a little about programming a CISCO router but I know the config I setup is not working...
Here is what I want to do...
The ISP provides us with IP Addresses via DHCP. Our public address is NOT static so the interface on the DSL Module needs to be provisioned to get a DHCP address with a CLASS C License.The IP address of the Router should be 10.0.0.10 subnet=255.255.255.0The LAN Clients need receive their IP address via DHCP EXCEPT for a range of 100 addresses. The lan Clients only need about 40 DHCP addresses.ONE of the Lan Clients (10.0.0.3) needs to have ports 25, 1723, and others forwarded to it.
Below is the config I am trying to use but I can't even ping the router from the LAN.
View 41 Replies
View Related
Feb 6, 2011
For educational reasons (a Videoconference class), I need to connect two 1841 router with each other. They both have HWIC-2T modules, but it's almost impossible for me to have the CAB-SS-2626X Smart Serial crossover cable on time. So, I was wondering if there will be some kind of a problem if I connect them through a UTP crossover cable using their FastEthernet interfaces. I suppose it will not "simulate" a serial wan connection but, would it work as a router to router connection?
View 1 Replies
View Related
Jul 21, 2012
As a Cisco newbie I am thinking about building a linux router (for a study project) to connect to a Cisco network (2 x 1841 routers). what kind (standard) of serial interface card will I need to install on the Linux PC router to enable serial communications with the other two 1841s.
View 2 Replies
View Related
Jan 10, 2013
Here's my setup:
- Cisco 1841 connected to the internet on fa0/1
- LAN connected to fa0/0/1 (switch port, connected to Vlan1)
On my LAN I have a web server that houses different websites. Those websites have DNS records that point to my public IP address, located on fa0/1. From the outside I can reach the websites perfectly, but I can't reach them from the inside. So it looks like I can't seem to connect from my local LAN address to the public ip address on the Cisco (who then should NAT it to the correct server)
Here is a snippet from my config:
--NAT--
ip nat inside source static tcp 192.168.0.3 80 interface FastEthernet0/1 80
ip nat inside source route-map Internet interface FastEthernet0/1 overload
--OUTSIDE INTERFACE--
interface FastEthernet0/1
description WAN
ip address dhcp
ip access-group WAN-IN in
[ code]...
--INSIDE INTERFACE--
interface Vlan1
description LAN
ip address 192.168.0.254 255.255.255.0
ip access-group LAN-IN in
[Code]....
View 3 Replies
View Related
Feb 12, 2012
I'm trying to configure an IPSEC VPN + tunnel for multicast data. When the default gateway is set on the router (1841) it works fine but if I only set a route to the IPSEC peer via our gateway then the tunnel fails to come up. The end point is to a 3rd party. [code]
I found that if I add a static route for the tunnel destination via fa0/0, the public facing interface, the tunnel comes up..ip route 10.23.4.2 255. 255. 255. 255 FastEthernet0/0
and I can then ping the tunnel IP at the far end - 10.23.0.5.Why would that be? Is there a better way to do this without using a default route??
View 4 Replies
View Related
Oct 22, 2012
While I managed to connect to each router individually, I decided it was time to connect the routers together via serial; as I don't have any serial cables and need to buy some, what serial cables I need, as well as to ask whether I have the right cards in my router(s) that will allow me to do so.
I bought 3 1841 routers, and all have a 1 port serial WAN Interface Card (WIC 1-T); one router has 2 of these, and one router has a WIC-1B-S/T .. My question is, can I connect the routers with a serial cable via WIC 1-T, or do I need a 2-T
View 1 Replies
View Related
Apr 1, 2012
I connect to my corporate network using Cisco AnyConnect Secure Mobility Client. Once connected I can no longer print to my LAN attached printer and other local resources. I use the Cisco/Lyncsys E4200 router on my LAN and can re-connect to the storage on the local LAN by setting up Port Forwarding of port 21 and MS Windows FTP folder sharing. However, I can't seem to connect to a Terminal Services client by forwarding port 3389. Is there a way to connect to the local LAN after logging into the VPN connection. I can connect to regular HTTP/HTTPS sites and most other type of connectiins, just not my own local resources.
View 3 Replies
View Related
Jan 19, 2011
I'm having trouble connecting to my IPS module via ASDM and web browser after configuring an IP address for the IPS module via CLI.The 5510's management port is plugged into our switch, and a VLAN is assigned at the switchport. I gave the IPS module an IP address in the same subnet (DG as well) as the 5510's management port, assuming the IPS module would communicate over the 5510's management port. Is this not right? I'm limited to the CLI for now, and would really like to access the IPS module through the ASDM.
View 6 Replies
View Related
Aug 23, 2012
i bought new RF Cisco 7204VXR NPE-G1. As soon i enable OC3 module ( PA-POS-OC3SMI) CPU of the router shoot to 100%, and if i reboot the router, it wont comeback not even on Console. I had to remove the POS card and then boot router and then hot insert the module.
so i put the command
int pos 4/0
loopback internal
as soon igave this command, CPU dropped down to normal. Whats the deal here? now i need to activate the circuit on this POS interface, but as soon i remove loopback internal command , CPU shoots to 100% Although CPU sorted dont show any process causing it.
[Code]....
View 1 Replies
View Related
Apr 9, 2013
I want to add module of WS-X6716-10GE(-3C). The type of 6500 isCisco WS-c6509-e (r7000) processor (revision 1.2).Can I add this module to this type of 6500?Do I need to reset the 6500 in order to the 6500 receive the module?
View 2 Replies
View Related
Jan 25, 2011
I have the situation with my new Cisco 2951 router. It has only one module on board - SM-D-ES3-48-P. I don't know what is wrong but I can't see any information about this module. When I connect my laptop to any port it's become green, but it's still green even after I disconnect PC from this port. Sh ip int brief command shows only built-in gigabit interfaces. I also connect my second PC to the router by console to monitor any changes when I connect or disconnect laptop to the module's ports. [code]
View 3 Replies
View Related
Oct 31, 2011
Will Cisco LMS Prime 4.1 be getting a map module, so you are able to see a graphical map of up and down status of devices? I know the topology map is a module within LMS, but what would be nice to see is a graphical map, where you are able to manipulate the icons to place them on that status map.
View 2 Replies
View Related
Oct 9, 2012
Wat will be the default memory and hard disk for SM-SRE-710-K9 and wat will be the maximum support for this module.
View 1 Replies
View Related
Apr 8, 2013
I have cluster of firewalls which inclueds AIP module and are in production. Due to some issue modules could not be activated. Now I need to activate and udate signature of them. So whether I can do all this activity without effecting my production (Zero downtime).
View 5 Replies
View Related
Jun 28, 2012
I know to add a user in the service engine is (config)#user Aileen create but how would you remove it. I tried no before user to negate the command but i do #sh users and the username is still listed.
View 1 Replies
View Related
Dec 19, 2011
We have a cisco 7204 VXR and would like to know the module which has two fastethernet port. We tried a PA-2FEISL-TX but it did not work.
View 1 Replies
View Related
Jan 28, 2011
I have Cisco ASA 5510 with CSC-SSM-10. ASA anti-virus service can not update the Base and Plus lisense. No Activation Code required for renewal. I go to "Administration> Product License" in the CSC SSM console and click "Check Status Online" to get the latest expiration date.In the module on the Check Status Online has reported the following error when: Base License status could not be checked because of a license server failure. "Please try again later", "Plus License status could not be checked because of a license server failure. Please try again later". UPDATE manual virus database can be seen in the latest available version, can not be upgraded because the service expired.
View 2 Replies
View Related
Mar 26, 2011
if the 7600-SIP-200 supported in VSS mode or not ?
I have configured to Cisco Catalyst 6513 as VSS, both of them have the 7600-SIP-200 module, before converting them to VSS I was able to work with the 7600-SIP-200 module, but after I did convert them to VSS, both modules didn't work.
here is the show module output, after VSS conversion:
VSS1#show module Mod Ports Card Type Model Serial No.--- ----- -------------------------------------- ------------------ ----------- 1 0 4-subslot SPA Interface Processor-200 7600-SIP-200 JAE14500GMT 7 5 Supervisor Engine 720 10GE
[Code].....
View 1 Replies
View Related
Feb 14, 2012
how to show all the module on the ASR 1004?
View 4 Replies
View Related
Nov 15, 2011
Does the ASR-1000 accept an HWIC module, or must one go to a SIP/SPA for all modules?
View 1 Replies
View Related
Feb 7, 2011
For some test in my lab , I ordered on e-bay a AIM-VPN board , they guy told me that it work in a C1841.When I compare to the one I have in my C2621 , they look equal.On both pcb I can read : CN6I280AAA
View 3 Replies
View Related
Jun 2, 2013
We have installed 5585-x in active/active mode with transparent firewall. We have created two virtual sersors for vs1 and vs2 in IPS module and linked with ASA context C1(vs1), C2(vs2) and admin(vs0).
As firewall is working in transparent mode, we have bridge IP address for context C1 10.1.1.1 and for context C2 10.2.2.1.
I have added default routed for context C1 10.1.1.2 .It is in the outside of asa and SVI on switch.For the other context C2 10.2.2.2.
IP address range for the IPS module and what should be the gateway for IPS module.AS the traffic is coming from outside and going to inside interface of ASA.
View 1 Replies
View Related
May 20, 2012
What module is used to push configurations in LMS 3.2.1?
View 1 Replies
View Related
Oct 11, 2011
I have checked on Cisco.com and as per a module support document for ISR's G2, the NM-1CE1TI-PRI module is not supported on new ISR's.
Grateful if more clarification could be obtained about the above.
Will be router not detect the module when inserted in the chassis?
View 2 Replies
View Related
Mar 7, 2012
We want to implement HSRP between two 3945 ISRs:
RouterModelIOSModuleR1Cisco 3945 Integrated Service
Routerc3900-universalk9-mz.SPA.151-1.T.binNME-AIR-WLC12-K9
R2Cisco 3945 Integrated Service
Routerc3900-universalk9-mz.SPA.151-4.M1.binNME-AIR-WLC25-K9
The issue that we are experimenting is that, although the module's interfaces are up and HSRP in correctly configured, the show standby summary displays that the Active router is local in both routers. We also have some GigabitEthernet in the routers and they are correctly running HSRP. Does the WLC Modules physically support HSRP?
View 1 Replies
View Related
Feb 13, 2013
how to enable the SFP module on cisco 2921?
View 3 Replies
View Related
Mar 24, 2011
I am using an ASA5510 and I would like integrate the CSC SSM module in it. What is the Process to upgrade, is it possible and Where I can find it ?
View 1 Replies
View Related
Apr 29, 2011
I have 2611xm router with 2 fastethernet ports. Now I want to install NM-1FX-TX module. I just want to conform that does 2611 supports NM-1FX-TX module. I am using this device for lab purpose. I am using latest IOS"
View 2 Replies
View Related
Sep 1, 2011
I recently installed the license ACE-SSL-05K-K9 on ACE10 with multicontext solution.The license provides 5000 Maximum number of SSL transactions per second (TPS).The customer would like to track this to find out the correct size and in the case of services https upgrade licenses.Can I do it so through particular output or it's necessary monitoring with snmp service? In the second case, can you tell me the oid string to use?
In case the module should receive a higher number of connections to that provided by the license, what's the issue for new https connections?
View 3 Replies
View Related
Jun 19, 2012
i just configured GRE over IPSEC on my Cisco 3745 router with VPN module installed. As soon i hit 25Mbps traffic, my CPU is touching 80%.
What maximum Traffic 3745 with GRE over IPSEC it can support?
Also show process CPU sorted dont show any evidence of which process eating it up.
sh processes cpu sorted
CPU utilization for five seconds: 75%/75%; one minute: 77%; five minutes: 78%
PID Runtime(ms) Invoked uSecs 5Sec 1Min 5Min TTY Process
[Code].....
View 3 Replies
View Related
Oct 1, 2012
I have a couple of ASA 5510 firewalls configured and working. I'm now charged with configuring the IPS modules. I'm having to do this remotely. Since the IPS module hasn't been configured I'm guessing it's on 192.168.1.2 with the default username/password.
I'm told that the workstation I access from connects through a switch to the ASA and to the IPS.
I've set the ASA management port to 192.168.1.1. I can't ping 192.168.1.2 - not sure I'm supposed to be able to. In the ASDM, Configure IPS prompts for an IP address. Entering 192.168.1.2 returns "IP address of the management port is unreachable".
View 4 Replies
View Related
Aug 19, 2011
I have a question about upgrade NAC Module, I follow standalone procedure to do the upgrade but I wonder about the upgrade file should I use because on the Cisco site I didn't find the upgrade file from 4.8.0 to 4.8.2.
what I found is nme-nac-upgrade-4.8_2-from-4.6.x.tar.gz ??!!!
So my question If I use the NAC upgrade file I was used for upgrade the CAM & CAS applaiances
View 2 Replies
View Related