Cisco Firewall :: PIX515 To ASA5510 8.4(5) Migration?
Dec 18, 2012
We're migrating as mentioned in the subject and this new format is quite a departure from previous iOS versions so I thought I'd post the configs of the PIX and the ASA and ask if someone is willing to compare them and verify that it is correct and should be basically plug and play. The xxx.xxx.xxx are outside IP addresses and the yyy.yyy.yyy are inside addresses. .
Existing PIX config
PIX Version 6.3(4)
interface ethernet0 100full
[Code]......
View 2 Replies
ADVERTISEMENT
Oct 13, 2012
Recently I changed our default gateway from a pair of PIX515 to ASA5510. Since I changed the gateway anyone connecting to our wireless VLAN/network who tries to access the Internet may or may not get a page load. If the page loads it is extremely slow and sometimes the browser page indicator will just spin like it is loading. It's not our access points, if attach an ethernet cable to my laptop and put my switchport in the wireless VLAN I experience the same problem. DNS resolves OK, ping responses are consistent with no drops and access to any internal resources are good. All other LAN VLANs/networks work just fine, it's just Internet access on the wireless VLAN. I see the correct traffic flow in the ASA packet capture. Anything in the ASA Packet inspection related to wireless networking that could be blocked? Is there a way to check for a routing loop possibly?
View 2 Replies
View Related
Jul 3, 2012
i exported config file from asa5505. i changed this file and i imported in my asa5510. can you tell me that config file allright
View 1 Replies
View Related
Jun 10, 2012
We have a wifi network for guests, that we route to internet through an old PIX515 Firewall. We recently tuned the timers to lower values in order to "save" on resources and publix address usage.
The timers we use are:
-timeout xlate 0:30:00
-timeout conn 0:30:00 half-closed 0:05:00 udp 0:02:00 icmp 0:00:02
Through verifying the new timers, we noticed at some xlate connections (TCP PAT) that are idle for ever!!In the connection table, I cannot find an idle connection for longer than 1h....
View 1 Replies
View Related
Feb 7, 2011
I'm planning connect VPN concentrator in our company to PIX515 DMZ interface.At the moment , VPN concentrator(used for remote access VPN for laptop users) is connected directly to core switch so as PIx515. Having VPN Concentrator connected directly to LAN is security risk .SO i want to connect VPN concentrator to DMZ of the Firewall(pix515).
We don't have any test environment and we are not allowed to have downtime of more than 10 minutes in production network ,I want to make sure my design and commands would work without problem .I've attached doigram of our curernt setup and new setup I'm planning to work on as well as commands . Does this design will work .Nat , routing everything .
View 15 Replies
View Related
Jun 14, 2012
I am unable to ping my computer (attached via crossover). I can ping from the PC, but not from the PIX515. I'm using ethernet 1, and I have its IP set at 192.168.1.2/24, but for what ever reason I am unable to contact the computer. I tried messing with the access list a little bit but nothing so far.
PIX515(config)# show run
: Saved
:
PIX Version 6.3(5)
interface ethernet0 auto shutdown
interface ethernet1 auto
nameif ethernet0 outside security0
[code]...
View 7 Replies
View Related
Jun 12, 2012
I have PIX515 with version 7.0 installed, so can i install version 8.3 on it?and what will be the memory requirements?
View 2 Replies
View Related
Jul 4, 2011
I have a pix515 v6.3.3. Is it possible to configure dual ISP on two interfaces and have redundancy between them?
View 1 Replies
View Related
Nov 14, 2011
I have one outside interface with global IP address 1.1.1.1 and two inside.Both inside interfaces restrict and non_restrict have private IP addresses.I tried to filter some URLs on PIX515 IOS 7.2, only on restrict interface but my filter does not work.I can access prohibited URL from restrict interface. What's wrong in my URL filtering?
Here is my config:
PIX Version 7.2(2)
!
hostname pixfirewall
enable password 8Ry2YjIyt7RRXU24 encrypted
names
[code]....
View 1 Replies
View Related
Mar 29, 2011
I am using a Pix 515 with IOS 8.0(3).I have in my access list on the outside interface.......access-list outside_access_in extended permit icmp any 12.23.34.0 255.255.255.0 echo access-list outside_access_in extended permit icmp any 12.23.34.0 255.255.255.0 echo-reply.......in order to allow ping requests and ping replies into my inside network. This certainly works since I can ping the inside from outside and vice versa, but in the ASDM display of access rules, the hit count for these two lines is always zero. If I run 'show access-list', the hit count for these lines is non-zero.
Why doesn't the hit count show up in the ASDM gui display?Also, I have read that the PIX does not treat ICMP in the same way as TCP or UDP and there is no stateful behaviour towards ICMP. However, if I set up a continuous ping from outside to inside and then disable the above access list rule allowing echo requests towards the inside, the ping continues whereas I would expect it to stop.
In the config there is 'timeout icmp 00:00:02' if there is no stateful connection for ICMP, why is there a timeout value for it?
View 4 Replies
View Related
Jan 7, 2011
I am having a spot of bother with a Cisco PIX515, I have posted the current running config below, now I am no cisco expert by any means although I can do basic stuff with them, now I am having trouble with traffic sent from the outside to address: 10.75.32.25 it just doesn't appear to be going anywhere.
Now this firewall is deep inside a private network, with an upstream firewall that we don't manage. I have spoken to the people that look after that firewall and they say they they have traffic routing to 10.75.32.21 and 10.75.32.25 and thats it (although there is a website that runs from the server 172.16.102.5 which (if my understanding is correct) gets traffic via 10.75.32.23. [code]
View 2 Replies
View Related
Apr 18, 2013
We are setting up an old office building as an offsite data center. The network cosists on a PIX 501 firewall and a 2811 router. I am attempting to setup a GRE tunnel over IPsec back to the main office. The main office consists of a PIX515, a 2821 router, and a 2921 router.
There is also an ASA5510 in our main office that is used as our primary connection for all of our external services and as a GRE endpoint for our other offices. The PIX515 is used to connect our main office clients to the internet and we would like traffic between it and our offsite data center to go across it as well. The default route is to use the ASA. We used policy based routing on the 2821 and 2921 routers to direct the appropriate traffic to the PIX515. Right now I am not able to get the tunnel setup. It appears that the offsite datacenter is sending packets but is not receiving any when I issue the “show crypto ipsec sa” commands on both firewalls. I will show the output of that command below.
Main Office The external address 198.40.227.50. The loopback address 10.254.10.6 The tunnel address 10.2.60.1
Offsite Datacenter The external address 198.40.254.178 The loopback address 10.254.60.6 The tunnel address 10.2.60.2
The main office PIX515 Config :
PIX Version 7.2(2)
!
interface Ethernet0
mac-address 5475.d0ba.5012
nameif outside
security-level 0
ip address 198.40.227.50 255.255.255.240
[code]....
View 2 Replies
View Related
Apr 13, 2011
We have got site to site VPN configured between local site with PIX515 6.3(5) and remote site with ASA 5505 7.2(4) . Because of very unreliable internet connection in remote site , we have added new ISP link which we want to use as redundant link .i understand ASA 5505 can be configured with two ISP link with SLA monitor method for redundancy as per this document ,[URL]
my question is how do i set up this pix 515 to have redundant VPN tunnel with remote site (when primiary ISP link fails in remote site and secondary ISP links takes over ) . I was thinking of using PIX 515 with 2 peers in same crypto map used for that sepcific site to site vpn tunnel,not sure that is the right way or not though.But how would i configure ASA 5505 to use backup interface(where secondar isp router conects ) to particitae in Site to site Tunnel .
View 4 Replies
View Related
Jun 6, 2012
ASA 5510 have two model Bun-K9 and Sec-Bun-K9 from the datasheet find out difference Port related and Redundancy. My questions is : Have any major difference for Security service between two model ?
View 3 Replies
View Related
Mar 8, 2011
As we are all aware that the ASA8.3 has quite some changes interms of configuration method.
I would like to know if it is possible to use the pix to Asa conversion tool for 8.3 purpose.
View 2 Replies
View Related
Feb 12, 2013
I have old ASA with 8.0 configuration that includes huge number of ACL, NAT , VPNs , we got a new ASA with 8.6 , and we are planning to move the configuration to the new box , I'm wondering what is the best approach to do this , I'm thinking of one of the following scenarios1- downgrade the new ASA to 8.3 , the apply the config , remove the identity nat commands and names then upgrade to 8.6 and after that reconfigure the NAT rules and object groups .2- convert the old config manually to 8.6 code including NAT , object-group ,ACL and apply it to the new ASA ( this is going to be huge task). What are the commands that I have to look at when I convert to 8.6 and will the VPN configuration be affected ?
View 5 Replies
View Related
May 28, 2012
I have a PIX 515 with version 8.0(3). We buy a ASA 5525-X for replace the PIX.
The question is, what is the better method to migrade the configurations? Manually?
What is the better version for 5525-X? 8.6.1?
View 4 Replies
View Related
Oct 25, 2012
I was trying to upgrade an ASA to from 8.2.4 to 8.4.4, and I began receiving the following migration errors (the IP addresses have been changed to protect the innocent):
ERROR: MIGRATION: The following ACE is partially/not migrated to Real IP, as it could result in more permissive policy. Please manually migrate this ACE. permit esp host 1.1.1.1 host 2.2.2.2
I got a TON of these, in fact the migration, and these errors ran for over 24 hours before I gave up, powercycled the unit and forced 8.2.4 to boot through ROMMON. This was a secondary unit, that's why I let it go this long.
What I don't understand is that we do not have anything in the configuration for ESP.
View 1 Replies
View Related
Oct 3, 2012
I don't seem to be able to find a migration utility for PIX rel 8.0.4 to ASA 8.6 is there one available will save a lot of time
View 1 Replies
View Related
Aug 26, 2012
Looking at migrating from the following:
PIX-515EPIX Security Appliance Software Version 8.0(4)Device Manager Version 6.1(5)51
to
ASA5515Cisco Adaptive Security Appliance Software Version 8.6(1)Device Manager Version 6.6(1)
Is this migration directly supported, or do I need to downgrade first?
View 5 Replies
View Related
Jan 23, 2013
I have ASA-AC-M-5520, can we migrate the license to ASA-AC-M-5585
View 1 Replies
View Related
Sep 24, 2012
I'm testing upgrading an ASA from 8.2.5 to 8.4.4. During the the upgrade, it change all of my ACL host entries to objects. But I noticed that the keyword "host" is still a valid option when creating an ACL.
I'm trying to understand why this change is made during the migration.
View 3 Replies
View Related
Apr 23, 2013
I am about to carry out a migration from ASA 5550 to ASA 5555-X, however I cannot find any detailed document or reliable tool for this migration.
View 4 Replies
View Related
Jan 22, 2013
Customer has a ASA5540 at their main location and need a new ASA5500 for a DR site.
Can I simply take a config file from an ASA5540 and easily drop it on an ASA5545-X or what ever?
They are going to be using it as a VPN concentrator primarily.
Or are there going to be issues since the 5540 is running 8.4(5) and the 5545-X? Or if they upgrade to 9,0(1) or higher, then they should be the same?
View 2 Replies
View Related
Nov 26, 2012
My company (in Healthcare) is going to be changing ISPs for our internet connectivity, and with this change comes a new external IP block. So I need a scheme to migrate over all of my existing VPN tunnels and other items over to new IP addresses. We do have an external router which I plan on doing a route-map to handle which traffic the ISP should go to based on IP. My big concern is for the ASA 5510. Can I setup a second outside interface on the new IP range? Then migrate my VPN tunnels over one-by-one? A drop-dead cutover date is just not possible with all of the external companies that I have to contact to get VPN tunnels updated with. If it's not possible, we have in our budget to get another 5510 next year as a redundant unit. I may be able to get that early and just migrate from one firewall to another.
View 3 Replies
View Related
Mar 23, 2011
in the ASA Migration Guide for Version 8.3 says about real ip address: "All of the access-listcommands used for these features are automatically migrated unless otherwise noted"
But my ACL's have not been migrated to real ip address. In my migration log:
INFO: NAT migration completed. Real IP migration logs: No ACL was changed as part of Real-ip migrationWhy?So, do I have to migrate them manually?
View 3 Replies
View Related
Feb 22, 2012
when I migrated the ASA config from 8.2 to 8.3, in all groups the group members has been replaced by the IP address object. However, the "name" for this object has been migrated, but there is the "object network name" configuration missing.
What I can do now is that I can open the new created object in the ASDM, search for the object with this IP address and then enter the object name I had before. When I apply the config, ASDM then creates the object and replaces all affected objects in all groups, by replacing the object group memeber "network-object host hostname" with "network-object object hostname".
Do you know if there exists an automated way, which checks all the groups for members "network-object host", creates the "object network" and replaces the "network-object hosts" with "network-object object" within the group? As long we have a lot of groups which contains partially > 50 members?
View 2 Replies
View Related
Jul 8, 2012
We currently have redundant FWSM's and are planning a migration to standalone ASA 5500 series firewalls. However, we have a complete VMWare environment and are looking at the Nexus 1000V. I understand the Nexus 1000V and VSG architecture and implementation, and I do understand that the ASA 1000V is designed for cloud environments. But I do have one question about the ASA 1000V.
Is it possible for an ASA 5500 series firewall to be replaced by an ASA 1000V? Basically, can an ASA 1000V be a sole firewall solution, or are ASA 5500's still needed? Is there a datasheet anywhere that compares the ASA 1000V and ASA 5500 series?
View 4 Replies
View Related
May 20, 2013
I've recently migrated a PIX 525 to ASA 5520, but for some reason (through ASA) the users from OUTSIDE aren't able access services published in DMZ as well as some DMZ servers aren't able to communicate to some OUTSIDE services.
-INSIDE to DMZ is working fine. (through ASA)
-INSIDE to OUTSIDE is working fine. (through ASA)
Below is the configuration from my PIX (where everything works just fine) as well as the one on the ASA (where there is a problem), what could be the cause?In the below case the DMZ hosts from 11.1.10.0 aren't able to access SMTP services (through ASA) and the OUTSIDE users aren't able to access DMZ web server (11.1.10.40) through ASA, this all just works fine with PIX.
object-group network inside_subnet_all network-object object inside_subnet_a network-object object inside_subnet_b network-object object inside_subnet_c network-object object inside_subnet_d network-object object inside_subnet_e network-object object inside_subnet_f network-object object inside_subnet_g network-object object inside_subnet_.access-list OUTSIDE extended permit tcp any object host-11.1.10.40 object- group WWW-HTTPS access-list DMZ extended permit object SMTP object dmz_subnet any access-list INSIDE extended permit ip
View 1 Replies
View Related
Apr 24, 2011
I have just upgraded a ASA5510 from 8.2 to 8.3 using migration tool.All seemed to go well, still double checking the config as this is a bench test of upgrade prior to filed upgrades.
Anyway one thing that is slightly frustrating is that the migration has expanded all of my access-lists, so we maybe had 10 lines of config relating to access-lists based on access-groups, now we have hundreds of lines.On ASDM this is bad enough but on CLI with show run its a bit of a bind.
Is there any way to un-expand the access list or do I simply delete and start again using my access groups.
View 2 Replies
View Related
Jun 11, 2012
I am able to ping from Switch to firewall inside ip and user desktop ip but unable to ping from user desktop to FW Inside ip.. config is below for both switch and FW Cisco ASA5510....
TechCore-SW#ping 172.22.15.10
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 172.22.15.10, timeout is 2 seconds:
[Code].....
View 7 Replies
View Related
Jun 29, 2011
I have two ASA5510's set up in failover, and the secondary keeps crashing after doing the interface checks when bringing failover up. This only happens if I try to upgrade the image on the secondary to anything newer than 8.4.1 (I've tried with 8.4.1-11 and 8.4.2). The primary one run just fine with new images.
I don't have the exact error right now, as I need to do a screen capture from console. It's just a huge crash dump.Are there anything I might have missed during the upgrade? Should I cold-boot both the firewalls in the correct order?
View 7 Replies
View Related
Sep 10, 2012
i have a ASA5510 in the office, that already configured 3 context, namely, admin, user, server.in the server context, the last running config was not saved, and there was a power trip last friday night. 1 of the sub interface was affected, and i need to recreate that interface.I am getting the below error, it only allow me to do changes those pre-defined interface.how to I create extra sub interface?
View 3 Replies
View Related
