i have a problem with a 4006 switch, when the poer goes out and comesback, the switch doesn't boot, you have to get in the console and type boot, the config register is 0x102, i try to change it but it did not let me, said somethong like usage, what can i do to configure the booting automatically
View 1 RepliesMy existing 4006 chassis is using Supervisor III (WS-X4014). I have another 4506 chassis using Supervisor IV (WS-X4515) and a Net flow Services Card (WS-F4531) build on top of it.
I need Net flow Services Card in 4006, so can I just replace the Supervisor IV (WS-X4515) used in Cisco 4006? Is it compatible with 4006?
I have a Catalyst 4006 with Supervisor II engine. I have 48 port 10/100/1000 blades installed in it for connection to my servers. I am having a lot of problems with performance when connecting servers that are using 100 MB NICs. The speed of the connection is really bad. I have attempted setting the ports and NICs to 100MB Full duplex instead of auto-detect, but still get the same results.
I also have a 10/100 quad-port card installed in a NetApp filer. All four ports are trunked together and connect to 4 ports in the Catalyst. The ports in the Catalyst are trunked using the Port Channel feature of the CatOS. When I look at the port statistics on 3 of the 4 ports from the quad-card, there are a ton of runts and errors (both transmit and receive). The 4th port is fine, no errors.
Is it possible to enable login by http (web interface) to catalyst 4006 switch with WS-C4006 Software, Version NmpSW: 6.3(5) ?
View 21 Replies View RelatedI have a DLSW connectivity between 2800 series router and 7206 router. AS 400 is directly connected to 2800 series router and other server is connected directly to 7206 router. now i want to add one more server which will work as backup for the server connected to 7206 . What would be the connectivity/configuration to make it working in case primary server connected to 7206 is down or connection would automatically needs to shift on its backup server.
View 1 Replies View RelatedI have a Cisco 4006 (old school) and I am trying to setup etherchannel over 4 port. The issue I am having is flapping, it see's two IP addres on the same MAC address. The reason for this is bonding, so all 4 ports are bonded, but I have two servers that need to send a heartbeat between the two server hence the second IP, and the other IP address to send/recieve.
View 3 Replies View RelatedI have an older 4006 with a Supervisor II+. We now need OSPF support, which the Sup II+ does not provide. I have access to a Supervisor III (WS-X4014), which will provide OSPF support. Question is, are there any gotchas to shutting down the switch, replacing Supervisor Engines and then powering up? What about the flash card? On my current system, it appears that I am only using bootflash: , which is where the IOS resides (see below). Since my startup config is in nvram and my IOS is in bootflash, what's the purpose of the flash card in slot0: ? and where does NVRAM and bootflash actually live on a 4006 ( on the Supervisor Engine?)
sh bootvar
BOOT variable = bootflash:cat4500-ipbase-mz.122-31.SGA11.bin,1;,1;
CONFIG_FILE variable does not exist
BOOTLDR variable does not exist
[Code].....
we got a problem with our cat4006 coreswitch. The led on the supervisorengine is red, and several errors are appearing in the message log. [code]
View 1 Replies View RelatedI have been facing High CPU Utilization issue with few of my Cisco 4006 Switches together from last one month. Out of which 1 switch issue sorted out auto after 2 days however the problem is still exists with rest 3 switches.They are 6-7 year old and having one SUP engine and other are switch port modules.
View 5 Replies View RelatedI need to convert configuration from CatOS on 4006 to IOS on 4510. I am unable to find the conversion tool.
View 5 Replies View RelatedWe got a layer3 switched network, with one vlan for every switch, routed by a cat4006. [code] So can we put some ports on different switches in, let`s say vlan 50, with different ips? For example, Port 0/3 on Switch 1 and 0/8 on Switch 2, but keeping the ip of the "old" vlan? Or is it necessary to configure a specified vlan interface with ip-adress for every vlan if i want to route it?
View 4 Replies View RelatedI have a Catalyst 4006 switch in production and a spare switch of same model. I have to quickly copy the configuration from production switch to spare switch (both L2 and L3 configurations) How do I do that?
View 6 Replies View Related I tried to reboot manually and I changed the slot but the same behavior:
%SYS-SP-3-LOGGER_FLUSHING: Systema pausing to ensure console debugging output
%OIR-SP-6-CONSOLE: Changin console ownership to route processor
*** System received a Software forced crash ***
signal= 0x17, code= 0x24, context= 0x430213e4
PC = 0x4038c124, Cause = 0x1020, Status Reg = 0x34008102
Having a problem where the router will randomly boot everyone off the network and display a "limited access" status. This happens every few hours and it's actually pretty annoying. I downloaded the wireless test and these are my results. If it matters at all, our Router is "Mendes". [code]
View 12 Replies View RelatedI'm somewhat new to networking so bare w/ me if I get some of the verbiage incorrect. We are trying to upgrade our 2960G's to a new version of code (c2960-lanbasek9-mz.150-1.SE.bin).After doing:switch(config)#boot system c2960-lanbasek9-mz.150-1.SE.binand a write mem, we did a reload, but the new version didn't take. We realized that the boot loader version is too old to accept this newer IOS. Here is the how version output:[CODE]
View 7 Replies View RelatedI've just run the ACE 4710 and it seems that is booting up well but it stops when 'Setting up dynamic memory size' message appears.
INIT: version 2.85 booting
b4 lspci
1 Cavium device(s) found.
[Code]....
System Bootstrap, Version 12.4(12.2r)T, RELEASE SOFTWARE (fc1)Technical Support: [URL] Copyright (c) 2006 by cisco Systems, Inc.Socket jumper: not present Failsafe jumper: present = normalFPGA revision 0x00000026C7200 platform with 2095104 Kbytes of main memory
Readonly ROMMON initialized
Self decompressing the image : #################################################################################################################################### [OK]
%ERR-1-SRAM: Bus error on SRAM interface%ERR-1-FATAL: Fatal error interrupt, No reloadingerr_stat=0x80, err_enable=0xFF, mgmt_event=0x10
System bridge dump:
PCI B:3 D:0 F:0 Reg:0x00: device and vendor id = 0x648511ABPCI B:3 D:0 F:0 Reg:0x04: status and command = 0x02B00000PCI B:3 D:0 F:0 Reg:0x08: class code and rev id = 0x05800004PCI B:3 D:0 F:0 Reg:0x0C: hdr type, lat timer and cls = 0x80804000PCI B:3 D:0 F:0 Reg:0x10: PCI CSN0 BAR (LOW) =
[code]....
I have a ACS 1113 appliance (4.2 ver), I am trying to recover the forgotten password, when i insert the disc and restart the SE it's not showing the prompt to recover the password, i checked the boot path and priority everything is fine, the recovery disc is also fine ther r no issues with that it has been created as a bootable disc
View 4 Replies View Relatedi have a ASA 5510 that gets the following error when trying to boot:-
<0> kernel panic - not syncing: Attempted to kill init!
AP not booting and am not able to boot. Xmodem file system is available.flashfs[0]: unable to allocate available block.
The system has been interrupted, or encountered an errorduring initializion of the flash filesystem. The followingcommands will initialize the flash filesystem, and
[Code]....
I am using a cisco 2811 router.It is not booting properly.It reboots continously by just decompressing the image repeatedly..
View 2 Replies View RelatedI have the following Pix 515E Firewall, that has been working good for a few years. But suddenly, the Pix stop booting up. The only thing that is happening is the power and network traffic led flashes and the active led is off. So my question is that is this symptom a hardware or software problem and is it fixable with either new parts; or is my firewall dead. I suspect that it is a hardware problem since the active led doesn't light up. I cann't even enter the ROM Moniter mode.
View 7 Replies View RelatedI have recently bought a used 2600XM, I was trying to boot it, I get some errors and end up being the ROMMON mode:
ystem Bootstrap, Version 12.2(8r) [cmong 8r], RELEASE SOFTWARE (fc1)
Copyright (c) 2003 by cisco Systems, Inc.
C2600 platform with 262144 Kbytes of main memory
getdirent: bad file magic number, possibly out of sync
boot: cannot determine first file name on device "flash:"
[code]...
I have a customer that has an air-lap1142. He says that it boot to Rommon, and he has to issue the boot command to get it to boot. What is the rommon command to have the ap boot to the image automatically?
View 1 Replies View RelatedAt the moment I have a problem with a WLC. This WLC is not booting by the fact it does not have an image. In the past option 5 in the following menu was selected.
Now I received I message when I select option 6. Telling me that if I upgrade from an .aes image I will left the unit inoperable.
============================================================
Boot Loader Menu
============================================================
1. Run primary image (Image not found)
2. Run backup image (Image not found) - Active
3. Change active boot image
4. Clear configuration
5. Format FLASH Drive
6. Manually update images
Currently working on a personal project to diskless boot several PCs of different configurations. Trying to use software called CCBoot only because it seams to be the easiest way of uploading the disk images to the server. My problem is that when booting the test machine it will not load from the TFTP server (times out).168.0.2 and is on a network with a Cradlepoint MBR95 router which provides DHCP. The server handles one of my ISPs and the router the other, but I don't think that will be a problem. CCBoot support highly recommends I use the software for my DHCP, but can use an existing DHCP server[CODE]
View 2 Replies View RelatedI got Windows 7 Enterprise-32 bit which cannot run some old programs,games,etc.So i decided to install Windows XP professional, but there's a huge problem: The internet does not work when i change to XP, but when i change back to win 7 it works again. Should i call my internet provider?Unplugging,creating,disabling the internet does not work,also it's not the problem with firewall.
View 2 Replies View RelatedWhenever I restart or boot my computer, it loses internet connection (Local Area Connection Unplugged). I need to unplug the cable connecting my pc to the modem and replug it until the green and orange light comes on on the area where I plug the cble to the pc w/c means that there is already internet connectionSystem:Win XP sp3 OSGigabyte S-series motherboard ma74gm-s2Amd Athlon X3 processorMotorola SURFboard SB5101U/SB5101N Cable modem
View 8 Replies View Relatedi have an urgent situation that my catakyst C3550 wont booting up after i reset the startup-configuration using "erase startup-config" command. now everytime i connect to the catalyst it show me "switch: " not "switch>", i have try using "boot" command in the "switch: " session but it said"Loading ""...: permission denied"error Loading ""
View 2 Replies View Relatedmy wrt120n cisco wireless router keeps booting me off my network.it is next door usually have a great signal but fades in and out the box for router says its for wireless n.....all i can get is g.can i manually change the settings and should i get a signal booster or a bigger and better wireless router? then i go power cycle my routers and modem and it will sometimes work and sometimes not wifi is next door but less than 50-60'.
View 1 Replies View RelatedYesterday a coleagu accdently removed the CF card from the router now the router does no longer want to boot completely. It extracts the image from the CF card but when it has to initialize the configuration it stucks there for hours. Can it be that the startup config is somehow corrupted?
When i try to tftpdnld is says that the mac address is illegal.
The first line of the cookie looks like 04 ff 08 86 ff ff ff ff ff ff ff ff ff ff ff ff
System Bootstrap, Version 12.4(13r)T, RELEASE SOFTWARE (fc1)Technical Support: [URL], Inc.PLD version 0x10GIO ASIC version 0x127c2801 platform with 196608 Kbytes of main
[Code]......
i facing problem with my switch cisco 3560G, when it power on only System light is green and noting happen. i check with serial cable ( Console) but noting happen no booting.
View 2 Replies View RelatedWe have recently purchased new Sup2T to replace the Sup720. When we tried to copy the vlan.dat file across we are facing this issue. Sup2T is not booting up once delete the original vlan.dat file of the Sup2T & reload. Here is the console output during the process. What to do to get this Sup2T working.
[Code] ......