Cisco :: LMS 4.0.1 - Topology Shows Not In Network Links
Jun 21, 2012Using Topology I can show device view from all my managed VTP domains. I don't understand why all links are "not in network"!?
View 3 Replies
ADVERTISEMENT
Cisco :: LMS 4.1 - WAN Links In Topology View?
Mar 12, 2012The regular problem with the LMS topology and WAN Links when you see the branches are disconnected from the HQ BUT in my case the branches are already connected via Layer2 links but unfortunately some intermediate layer2 modem/switch exist in some branches which prevent CDP discovery but you will find both HQ and branch router in the same subnet .
View 1 Replies View RelatedCisco :: LMS 4.1 Topology View N7K Missing Links
Oct 17, 2011I work with the topology view in LMS 4.1. I can see all the links between the differrent switches (N7K, 3750, 3040).I miss only the links between the different N7K's. This links have one special thinks: they are configured as " rate-mode dedicated force" In the N7K cli this interfaces are displayed with the SN too.
sw-bb13# show cdp ne.The links to sw-bb11 and sw-bb21 are not painted in the topoloyview.
Cisco :: Prime LMS 4.2 Topology Layer2 View Missing Links
May 15, 2012We have a problem with the Layer2 view of the Topology java applet in Cisco Prime LMS 4.2.The Layer2 view shows all the ethernet interfaces links but not the ones in the serial interfaces.All devices have CDP and SNMP (read-only) enabled, and theirs neighbors can be seen with "show cdp neighbors" in both sides of those links.
View 4 Replies View RelatedCisco :: Topology Services LMS 4.2.2 Links Showing As Ethernet Channels?
Oct 15, 2012im trying to figure out the right way of configuring cdp on devices so that they dont show the links as etherchannels segments linked together, i have several port-channels in the network and the layer 2 view seems all messy.
View 1 Replies View RelatedCisco :: LMS 4.0 Stops To Refresh Network Topology
Oct 14, 2012After some time LMS stops to refresh network topology (not changing colors for devices which lost/found). However, if I restart topology services devices are refreshed.
Checked the processes. Everything is fine but there is a process named "1018". But I did not found any job with this number.
Network Topology IP Addresses And Vlan's?
May 28, 2012i create a network topology ( i attached picture) and i don't know what exactly IP addresses should be assigned to routers and switches + there should be five VLAN's created and just one vlan (vlan 2) must see others vlans (for management purposes) and others vlans should not see each other. So i need that: 1) What IP addresses should be on routers and switches 2) How to create a 5 vlans, that they should not see each other, but one should see all, for example where i have to put "tagged" ports where "untagged" or "not member" ports etc.
View 1 Replies View RelatedGetting Network Topology IP Addresses And Vlan's?
May 28, 2012i create a network topology ( i attached picture) and i don't know what exactly IP addresses should be assigned to routers and switches + there should be five VLAN's created and just one vlan (vlan 2) must see others vlans (for management purposes) and others vlans should not see each other. So i need that: 1) What IP addresses should be on routers and switches 2) How to create a 5 vlans, that they should not see each other, but one should see all, for example where i have to put "tagged" ports where "untagged" or "not member" ports etc.
View 4 Replies View RelatedHow To Connect Two LANs With Same Network Topology
Apr 27, 2012how can i connect two offices in the same town.these two offices are separated by two kilometres.each office has ten rooms.how can i provide a secure intranet between the two offices ,what media can be used and hardware to provide a secure intranet via the two offices.
View 2 Replies View RelatedCisco Switching/Routing :: 891 Deciding On Network Topology Of Router And FW
Jun 5, 2013We currently support a third party VOIP software. Recently we have had issues with our T38 faxing to our SIP Trunk provider because our FW (sonicwall) doesn't support Nating the connection address within the SDP packet of the T.38 reinvite. This has caused us to look at alternate solutions. I have been in discussion with CISCO sales engineers and can't get a straight answer on which one of their products support this(RFC 3362, T.38 protocol used by our VOIP server)We were looking at replacing our sonicwall with an ASA but it seems it doesn't support RFC 3362 either . However, the sales engineer thinks that their regular routers will. So If I purchase a cisco router, i.e 8xx or 2621XM the question is where do I put it in my current topograpy. Currently we our at a Datacenter and our drop into our cabinet comes right into the Sonicwall and we have all NAT handled there, routing to different LAN ports on the Sonicwall. On LAN side all we have are standard switches supporting all of our Servers.
If I buy a Cisco router to handle my NAT issue for faxing.Do I put it on the WAN or LAN side of my FW?Do I setup the router to handle all of my NATing or just the NATing of my VOIP server that is having issues with the T.38? Would I need a Sonicwall FW if I purchased a CISCO 891?
Home Network :: Why Used CSMA / CD In Star Topology Switch
Mar 29, 2011As we know when multiple PCs share same link"line" they will need multiple access protocol like CSMA/CD to protected from collision,,share link like "bus topology" need multiple access protocol "CSMA/CD" but in star topology"switch not hub" PC0 connect to port0 ,,PC1 connect to port1 PCn connect to portn then every PC connect to separate port ,, and the switch mange the network"by using MAC" then why we need to used CSMA/CD in star topology"switch"???
View 9 Replies View RelatedCisco :: Free Software To Create Network Topology Diagram 1231G
Apr 29, 2013I have a problem where clients cannot roam between Cisco 1231g-e-k9 and recently installed cisco 1242g-e-k9 access points.. On looking at the CDP option on the 1231 and 1242 access points they are all aware of each other. However if I use the Network View option I see a different picture. All the 1231 access points can see each other but not see the 1242's. Network View on the1242 shows all the 1231's but none of the 1242's. The 1231 are running ver. 12.3(8)JEB and the 1242's are running ver. 12.4(21a)JA1.
View 2 Replies View RelatedCisco Switching/Routing :: SR2024 / SR2016 - Customer's Network Topology
Nov 12, 2012I am a beginner, and my customer complaining about the internet connection performance which is very slow, the network description is given below:
Description:
The building has four floors and each floor has one mount rack which contains one 26 port switch + 16 port switch. and each floor has 32 pc as well.
- 4, Cisco SR2024 un managed switches.
- 4, Cisco SR2016 un managed switches.
- 1, Cisco access point for internet connection.
- 1, Active directory server.
- 1, Mail Server.
- Internet ADSL connection, 1 MB speed.
This is the current topology.
*Note:The links and cable type "100BASE-TX under Cat 5" among all switches.
*Note:Whenever I connect to the main router "Access point" the internet becomes very fast.
Cabling / Cards :: Connect 4-6 Laptops In A Mesh Network Topology?
Feb 18, 2012I need to connect 4-6 laptops in a mesh network topology. What equipment do I need (switches, hubs cable etc..) and how should I create the connection?
View 1 Replies View RelatedCisco Firewall :: ASA 5520 - Memory Shows 94% And CPU Shows 85%
Oct 15, 2012I Have asa 5520 with the code 8.0, the mem shows 94% and the CPU shows 85%
View 5 Replies View RelatedLaCie 5big Network 2 Drive No Longer Shows Up On Network?
Aug 11, 2012I'm trying to see if I can fix my friend's NAS which apparently has some pretty important data on it that wasn't saved anywhere else. They actually had the Geeksquad look at it and they've come to the same conclusion I have so far, but I figured I would ask the internet before I gave the thing back to them and said Geeksquad was right.
Anyways, they have this 5 drive RAIDed NAS which apparently just stopped showing up on their network. I borrowed it from them to see if I could figure it out. It turns on just fine and my router assigns it an IP address, but the IP address just takes me to a blank LaCie dashboard screen. It's weird because it's clearly running it's web server because it's just a gray background with an empty white box and "(c) LaCie 2010" at the bottom. No content at all.
Additionally, I tried installing the LaCie Network Assistant on my home computer and it says it cannot find any network disks. I've tried the "wake up a device" where I enter the mac address, but that doesn't do anything.
All the lights are solid blue on the front and over all the drives so it doesn't appear a drive has failed or something. Even so, that wouldn't really explain the blank dashboard right?
Network Shows Two Ssid Addresses?
Jul 10, 2012My church has a AT&T wired modem and a Netgear Wireless router. Pastors office is on other side of church and he is losing signal occassionally. His network is showing two SSID addressed cgcg cgcg2
View 4 Replies View RelatedComputer Shows That The Network Is Available But Won't Connect
Dec 1, 2012I have a wireless router. The first time I connected my computer to it, it worked. I went in to change the network password, and after that, it stopped working. Every single other device I have will connect, including other laptops, but this one won't. In the network and sharing center it shows that my network is available, but it will not connect. I have tried everything I can think of. I have looked all over the internet, nd still can't figure it out!!!! My computer's wifi IS on so its not that. The only thing that the trouble shooter tells me to do is unplug the router and restart it and that has not worked after several tries. Also is there a way to reset the computers recognition of networks? Im wondering if that would work if I could completely restart the process again, but I dont know how to get to that. I have a dell inspiron with windows 7.
View 1 Replies View RelatedWireless Network Shows Up As Local Only?
Sep 2, 2011After Irene, we kept power and cable, but our internet went down, or so we thoughtWhen we plug the Ethernet cable from the modem into the computer, internet works fine (I can post this, after all), but when we plug the cable from the modem into our Dell TrueMobile 2300 router, our network appears as "Local Only." The phone cable thing is plugged from the wall into the modem, and the ethernet cable goes from the modem to the router, as it has been for years.
View 7 Replies View RelatedHp Laptop Does Not Shows The Wireless Adapter In Network?
Jan 1, 2013My Hp laptop does not shows the wireless adapter in my network and sharing folder how can i fix it? i cannot connect on my wifi because of it .
View 1 Replies View RelatedVista Network And Sharing Shows Two Networks?
Feb 29, 2012I changed recently my wireless router (and my ISP) and since then the Network and sharing center lists two networks, both with Local and Internet access.One has the SSID assigned to the router and the other is name "unidentified".All seems to be working fine but i'd like to clean up the mess and remove this undefined thing.I have a vista home premium. The wired NIC is disabled, The wireless is set to dhcp with ipV6 disabled. Am attaching below the ipconfig /all.
Windows IP Configuration
Host Name . . . . . . . . . . . . : pavi
Primary Dns Suffix . . . . . . . :
Node Type . . . . . . . . . . . . : Hybrid
IP Routing Enabled. . . . . . . . : No
WINS Proxy Enabled. . . . . . . . : No
[code]....
Windows 7 Shows Wireless Network But Can't Connect
Nov 6, 2012I recently build a Frankenstein desktop, or at least that's what I'm calling.I started out replacing the motherboard in a HP Pavillion p6130y desktop.After some research I found that the stock motherboard as pretty outdated so I decided to go aftermarket.I wanted to replace as little as possible but now the only original parts are the dvd drive and network card.The network card has to screws on the back to attach an antenna and is a PCI1x card.
I now have a problem where after installing the card and Windows 7 Professional , I can see the list of available wireless networks including my own.But, I cannot connect to any of them even though my own network has full signal strength.
Windows 7 Laptop Will Not Connect And Shows Nothing In Network
Nov 14, 2011Replaced a router. My windows 7 laptop will not connect & shows nothing in the network window. It is like a setting on the computer has been changed.
View 3 Replies View RelatedConnected To One Wireless Network But Sharing Center Shows Two
Aug 23, 2012I am connected wirelessly on my laptop to my DIR-655 (D-Link) router. There is something weird going on to me in which is shows I am connected to two networks, one my home network clearly identified. The other one a "public network" listed as unidentified, all on one wireless connection. I run Windows 7 SP 1 32-bit. I would like somehow to merge or remove the second one from the listing.
View 1 Replies View RelatedIcon Shows Connected To The Wrong Wireless Network?
Nov 29, 2012when I hover my mouse over my signal bars it says I am connected to a network named 'home-9C78' but when I click to bring up my list of available networks, it says I am connected to a network named 'Reshiram' Reshiram is the name of my network and there is NO 'home-9C78' ANYWHERE in the list!!! I don't know where my computer gets this home-9C78!!! and I NEVER ever connected to a network with that name!!! it is supposed to be 'Reshiram
View 2 Replies View RelatedNetwork Shows No Access And Specific Connection Says Limited
Feb 18, 2013My network shows no access and the specific connection says "limited access".
View 2 Replies View RelatedNIC Shows Green Light But Does Not Connect With Other Computer On Network?
Aug 14, 2012My computer's NIC shows green light but it does not connect with other computer over the network.
View 1 Replies View RelatedNetwork Icon Missing Which Shows The Status Of The Connection?
Feb 5, 2013network icon missing which shows the status of the connection
View 8 Replies View RelatedWRT600N Network Adapter Shows Cable Unplugged
Feb 6, 2011I have a Lynksys WRT600N. I had DD-WRT on it and it was working great for about a year. One day I changed some minor settings like wireless signal type, reboot it and it's gone. I can not access it from my computer. The network adapter shows "cable unplugged". The lights on the front come on, but I can't get anywhere with it.
I've done all the resets I know how to do, including the 30/30/30 and leaving it unplugged for a few months.
Dell Vostro 1500 Laptop Shows It Is Connected To Network But It Is Not
Mar 27, 2011I have a Dell Vostro 1500 and I have AT&T wireless internet in my house. My other computers and Roku connect with no problem, but mine even though it says it is connected, is not connected. I have Windows XP the other computer is Vista and the desktop is also XP. Even AT&T came over the house and said something is wrong with the computer.
View 12 Replies View RelatedCabling / Cards :: Network Adapter Shows Connected But No Connection?
May 6, 2011ok so ive been messing with my aunts desktop trying to get it to run online.
her network adapter SAYS its connected but when i try to actually go online it says its not connected.
i checked the connection and it does say its connected. it is a fresh install and i reinstalled the driver for the internet.
ive unchecked the automatic config for the net options (saw in some suggestions)
Internet Losses Connection Randomly Shows No Network Access
Aug 6, 2011I need to know why I am losing internet connectivity like around nighttime, late. I keep losing internet on both IPv4 and IPv6! It both said "No Internet Access" Then later IPv6 said "No Network Access" That's the problem i am having on my personal laptop computer. I really am furious that I lost internet connection around 12:15, 12:30, 12:50, 1:30, 2:15, 2:30, and 3:30 A.M. i suddenly lost internet right there. And I heard the internet crew shuts down the internet system every nighttime and fixing it. I want to know why they need to fix it, how long will the repairs last ?
View 1 Replies View RelatedWireless Network Shows Full Signal - Can't Connect To Anything But Skype
Nov 8, 2012I had a small issue wherein my pc would lose ALL network connection to my pc, but the network icon showed that i had full signal, no issues. as long as i sign in on skype before the internet drops, it will stay on after it drops and i can still chat and everything, and to fix, i had to restart my pc. well, it had gotten better.And now its back, and WAY worse then before. skype doesnt have time to sign in upon bootup, and wont connect. steam wont connect, NOTHING will conect, but i still show full signal and no yellow mark or anything! I have done the following:
reboot(derp)
reinstall drivers
move wifi adapter
disable IPv6
[code]....
and no, i am not able to reinstall windows. I am going to try (soon, i am not able to just yet) direct ethernet to my router. all other PCs in the house are working perfectly, even this one that is slow as crap because it has windows 7 and is designed for windows XP.