I have run a netconfig jobs in LMS 4.2.1 with these settings: [code] After running the job the "Device Details" of the jobs say "Successful Devices" for all three switches:"Deploy successful (Primary Login Succeeded / Primary Enable Succeeded )" For the devices switch-1 and switch-2 I get the desired output: [code]. Why there is no output although the job is successful?
View 3 Replies
If i connected the latop to brand new out of the box ASA 5505 through consloe cable and i have a config file on this laptop from other ASA5505, is there anyway i can upload that config file into startup-config of this new ASA5505 through console cable, without using TFTP or FTP?
View 5 Replies View RelatedI have a Cisco 2811 router and when I turn of the router the running config is lost. I have to the following to get the router running of the start-up config settings.
router#copy start-up running-config
after upgrading from Prime LMS 4.1 to 4.2 (Windows version) the "All Devices" group and all the other system defined groups are empty.
The "Inventory dashboard" shows 397 reachable devices which is correct. I can access the devices when I type the name into the search field in the upper right corner of the LMS page.
When I open a device selector (e.g. from the "Device Management" tab) all system defined groups are empty.
When I make a new user defined group with the definition "IP address contains '1'" I get a group with all devices.
Allthough we see all our devices in Inventory Portlets, we cant access devices via device selector neither in CM, RME, DFM ...OGSserver is running?
View 2 Replies View RelatedI would like to empty my LMS 3.2 DB and re-discover all of my devices again. What is the best way to do this besides wiping the software and reinstalling?
View 1 Replies View RelatedI have a problem with the ACS 5.2 configuration: I am trying to use the AAA authorization to centralize privileges and commands but only the privilege level is sent to router, the command set aren't sent.
The test cenary is this:
ACS 5.2Router 2900 family IOS 15.0
The ACS is configured with:
Shell Profiles (to match with a privilege level), Command Sets (with the command list), Service Selection Rules (to set to one service) and Authorization (to assign one shell profile and one command set).
The router is configured with the follows commands:
[code]....
I am having issues playing certain games on my ps3. So I've been searching for solutions and I came across a video that wanted me to go to run/cmd/ipconfig. I have little knowledge of computers but I'm not sure that what my ipconfig is showing is supposed to be there. At first I googled and learned about ipv6 addresses because i found that weird but i think that checks out fine. I then googled about the weird numbers and letters in my default gateway and came up empty. Is there a reason thats there?
View 3 Replies View RelatedI have seen some discussion in the forums regarding user defined groups being empty in LMS 4.0 but not 4.1. I am having this issue in 4.1. Under User Defined groups, I have created 2 logical groups named "Physical Location" and "Switches". These do not contain any actual devices, they are just containers for other groups. Under the Physical Location logical group I have created 2 other groups, Acuna and Hampton. Under the Switches group I have also created 2 groups, HDM and HHC. The criterion for the Physical Location group is based on the first 3 characters of the hostname:
Device.System.Name startswith "hdm"
The criterion for the Switches group is based on the value of a user defined field, Admin_responsibility:
Device.Admin_responsibility equals "HDM"
The Physical Location groups work - the Switches group does not. Both the HDM and the HHC group should contain several devices. The HDM group contains 2, the HHC contains none. If I edit the groups and click "next" until I get to step 3, Membership: Edit, the "objects matching criteria" list is fully populated - it contains the devices that it should contain. However, after I click "Finish" and go to Inventory => Add / Import / Manage Devices there is no change in group membership - the HDM group contains 2 devices and the HHC group contains none.
After an upgrade from LMS 4.2 to 4.2.1 Legacy menu is completely empty. Is it a bug? If it's empty, how to get to some of DFM options (like rediscovery, discovery status etc.) They seem not present in "Site map".
View 4 Replies View RelatedI want to do something with IP SLA and started by estabilishing a baseline.
I'm trying to check history on an ASR. I tested same config on a 3845 and was forgetting the "history filter all". After this I could see history table on 3845 but still history is empty on the ASR1006. The operation started because I can see information with "show ip sla statistics".
know if i missed something or maybe this is not supported in ASR1006?
re-ld-tcc-02_ASR1006#show vers
Cisco IOS Software, IOS-XE Software (X86_64_LINUX_IOSD-ADVIPSERVICESK9-M), Version 15.2(1)S2, RELEASE SOFTWARE (fc1)
[Code]......
my network places on winXP is empty when i 'm in lan with 14other pc using a switch.
View 1 Replies View RelatedI am trying to copy a setup from a Nortel IAX100 where the carrier provides two ATM PVC's over ADSL - one for voice (VoIP) and one for data (IP). Relevant lines from the backup of the IAX's configuration include the following for the PPP authentication over the voice circuit:
<wan_8_32>
<entry1 vccId="1" conId="1" name="Voice" protocol="PPPOE" encap="LLC" firewall="enable" nat="enable" igmp="disable" vlanId="-1" service="enable" instanceId="1509949441"/>
</wan_8_32>
<pppsrv_8_32>
<ppp_conId1 userName="" password="" serviceName="" idleTimeout="0" ipExt="disable" auth="auto" useStaticIpAddr="0" localIpAddr="255.255.255.255" />
</pppsrv_8_32>
The null username and password for the PPP connection have me a bit stumped. Does the PPP connection not use any authenetication at all? (Is that possible/likely? How could I deubg it?) Or does does the IAX100 supply a chap/pap response with null credentails? (If so, how would I duplicate that using an instruction to a dialer interface?I am configuring an 877 with 12.4T and advanced IP services.
I replaced old cisco router 2811 with new one 2921 , all works except crypto map VPNs routers can ping each other , ACLs are not applied to outbound interfaces show crypto isakmp sa is empty after i make same configuration on a new router 2921 config.
View 1 Replies View Relatedafter switching from a very old ACS 3.2 to ACS 5.2 I'm wondering on how to specify an empty argument in a command set.
Example:
I want to permit:
write
but I don't want to permit:
write terminal
write erase
write network
write core
and so on.
If I specify command="write" and leave the argument field empty, every argument is allowed. This would also permit "write erase" what I don't want.
In ACS 3.2 I could specify command="write" and argument="^<cr>$". This does exacly what I want. The command write with an empty argument is allowed. If there is any argument, the command is denied.
In ACS 5.2 if I enter the same string in the argument field, the "<cr>" is filtered out and in the config is now only the string "^$" which is not working.
how to specify an empty argument?
BTW: ACS View shows only [ CmdAV=write ] in the logs...
while working with Cisco's CNA (Cisco Network Assistant) on a 2960 switch, any change done by this tool is sent out as an empty set of commands, to a TACACS server to approve.
I have 2960 switch, a PC with CNA on it and brand new ACS 5.2. This switch is set up for TACACS+ authorization. While working with TELNET/SSH, all commands are authorized properly. When doing "debug aaa authorization", you can see the commands are being sent to a TACACS server (as expected) for approval. And what is more important – within the debug output every command appears at "AV CMD= …" and "Arguments = …" Those commands seen by the ACS and approved correctly.But, when working with CNA, those fields (i.e. av cmd and arguments) are empty in the first place. Hence all what ACS does see are "empty commands" and no clue for the correct ones (say, changing interface's description). The HTTP server has it set of authorization commands.
I have a case for an LMS 4.0 running in a Live environement (With devices already discovered and organized into seperate groups), where the Device Credential and repository DCR is showing suddenly as empty and only i can see the groups listed, but without any devices in them (Through Inventory > Device Administration > Add/Import/Manage Devices).After a restart of the whole LMS server a few weeks ago, the problem was fixed and the devices appeared again, but now the same issue re-appeared.
View 5 Replies View RelatedWhen attempting to configure access controls from the advanced menu I enable the access control checkbox. I then follow the configuration wizard completing each step as directed by the wizard. When I complete the wizard and try to save the rule I get the following error message regardless of how I complete the wizard. "Name can not be empty string". Yes, cannot is misspelled in the message. I have tried every combination of choices in the wizard and many combinations of naming the rule to no avail.
This did work properly on a previous firmware version, probably 1.04 or 1.05. I have not tried back loading to the previous versions to see where it did or did not work. I don't know how well the router goes back and don't really care to reload all the settings again by hand if the automatic recovery doesn't work.I want to use this feature to control what hours certain machines on the network have access to the internet.
I have a problem with User tracking. After a restart of the daemon manager or a reboot of the server the end host table is empty. All end hosts then have to be discovered again. is there any possibility to backup and restore the UT-Database?
View 1 Replies View RelatedI have a cisco 6509 (ws-c6509-e) IOS 12.2.(18)SXF6 with the following modules and submodules: [code] I would like to add another module, I have WS-6816-GBIC or WS-6516-GBIC which one will work with my 6509 ? The 6509 has four module slots empty: 4-7-8-9, Can I add the card in one of these slots ?
View 10 Replies View RelatedHow do I have to tell the IOS on an Aironet AP1142N to delete (rmdir) a whole directory with its contents and maybe subfolders?I've tried "rmdir /recursive flash:/directory" but I get asked if I'd like to remove "/recursive"!I don't have the time to dig myself into every and each sub folder deleting single files.
View 8 Replies View RelatedEnv: Configured Cat3560's L3 port and vlan port, enable OSPF routing, SNMP server, etc. The routing info can be shown by CLI show ip route. But, using SNMP MIB broswer to read IpRouteTable(OID.1.3.6.1.2.1.4.21.1, MIB-II, RFC1213), nothing returned, seems IpRouteTable is empty.I would like to know:
1. Cat3560 works as L3 switch, if it support SNMP IpRouteTable, RFC1213?
2. Where is the Routing table of SNMP, is there specific routing table OID?
3. All the L3 switch has this behavior, or just Cat3560 works like this?
I have this problem since updating my firmware from 1.00.12 to 1.0016 (Annex A)
Problem: After leaving the router on for 1 day(dont know exactly how many hours), I tried logging in again on the admin page 192.168.1.1. Auth box appears, put username & password, but blank page after that. Tried using Safari/Firefox and it's the same. Router is working, all the LED lights are good, Internet is working, DHCP and all other config is normal. It's just that I can't access the admin page anymore.
When I power on/off the device, the problem is gone. Admin page is accessible again. But after some number of hours again, same problem blank admin page.
Does it has something to do with the router config like g.dmt/dsl 2 ?
I was wondering if anyone has seen their VPN User Connection Status Table empty even though you know for sure clients are connected? I connect with my iPhone to the PPTP VPN successfully and it works fine but there's no entry for the connection on the VPN User Connection Status Table. Is that normal? Does the router only collect data about Windows clients?
View 3 Replies View RelatedWe have a WAP 200 wireless G access point. It worked perfect before. About two weeks agao, we didn't change anything, it began to send empty alarm email every 10 minutes. We upgraded the software to newest version,restarted it several times. But till now, it still keep sending empaty alarm email.
View 1 Replies View RelatedOur customer has the business needs to authenticate remote users against AD with empty password. I've seen ACS5.1 release note where mentioned about resolved issue: #CSCte72751 #ACS 5.1 drops authentication with empty password.
I tried to authenticate dial-in users through Tacacs and Radius against AD with empty password but without success. ACS points to wrong AD password. Is it possible to authneticate remote users with empty password?
i repalced old cisco router 2811 with new one 2921 , all works except crypto map VPNs routers can ping each other , ACLs are not applied to outbound interfaces show crypto isakmp sa is empty after i make same configuration on a new router 2921 config crypto isakmp policy 10
hash md5
authentication pre-share
crypto isakmp key key address Y.Y.Y.Y no-xauth
[code]...
keys match , crypto isakmp policy is same , IOSs supoort VPN .interess traffic alse been initiated from both side and all worker in old cisco router with same configuration?
I created some acess-lists, and you can assign a logging level to this access-list. Now this ACL has a lot of hits, so i want to see whats happening. Only the log I then see is completely empty. I cannot figure out how to get some info in that log.
I think there is some global logging setting i probably need to enable in order to get anything logged at all, but i cannot figure out which.
First few attempts to load a web page after a reboot are okay, then it begins to stall with no error, or sometimes an "empty response" error message. I simply cannot load web pages. Checking mail sometimes stalls. When this happens, the Thunderbird process hangs around after I've exited the application using 50% cpu. I didn't discover this until just recently. Even when connecting to my own router 1 hop away, the admin web page timed out. Other things like downloading software updates and online help seem to be unaffected. FTP connection sometimes stalls. SSH takes forever (~10 seconds) to get a login prompt. Connecting directly to the cable modem has no effect. No other PC in my home has any problem getting online. I've tried changing DNS servers with no luck. Same problems with Ubuntu running in a virtual box in Windows. I can get online in Safe Mode. During the malware detection there was a question about my proxy settings, which showed up in a system scan, slowing me down. I didn't think that was contributing to the problem, but I've since deleted them and still no improvement. I just completed a round of malware detection in the other forum and my system appears clean, so I decided to come here and give it a shot.
Tech Support Guy System Info Utility version 1.0.0.1
OS Version: Microsoft Windows 7 Professional , Service Pack 1, 32 bit
Processor: Intel(R) Core(TM)2 Duo CPU T8100 @ 2.10GHz, x64 Family 6 Model 23 Stepping 6
Processor Count: 2
RAM: 3070 Mb
Graphics Card: NVIDIA GeForce 8400M GS , 128 Mb
Hard Drives: C: Total - 294907 MB, Free - 69444 MB;
Motherboard: Dell Inc., 0JX269, , .42MCPH1.CN7878389N001F.
Antivirus: AVG Anti-Virus Free Edition 2011, Updated and Enabled
EA4500 USB port for shared storage,Picture is missing, empty folder with the same name appears.
View 1 Replies View RelatedCisco keeps struggling with CCC firmware files.
Now the download link for E4200v2 CCC is available, but gives you an empty zip file (0 bytes). Quality Control is an unknown word at Cisco.
The file is no longer empty.
With firmware version 1.31, the Wireless settings page is blank when a browser other than Internet Explorer is used to access it - for instance, Firefox or Chrome.All other pages appear and seem to work properly, only the Wireless settings page is empty. Luckily, the Wizard still works and can be used to set the Wireless settings for general purpose use. Older versions of the firmware worked fine with other browsers, including the Wireless settings page.
View 6 Replies View RelatedI'm having a difficult time getting the logging mechanism to work on my DD-WRT Router. I've gone through all the accepted methods for enabling logging: Seems there're others having issues too, but no answers: URLS
Specs:
Router Model WZR-HP-AG300H
Firmware Version DD-WRT v24SP2-MULTI (11/20/11) std - build 17798
I investigated a little further on the router. I enabled ssh, logged in, and found the log the firewall reports too. So I know the logging is performed, it's just not linked up to the incoming/outgoing log web page. Here's the log:
Using username "root".
DD-WRT v24-sp2 std (c) 2011 NewMedia-NET GmbH
Release: 11/20/11 (SVN revision: 17798)
BusyBox v1.19.2 (2011-11-20 17:24:36 CET) built-in shell (ash)
Enter 'help' for a list of built-in commands.
root@rome:~# cd /tmp/var/
root@rome:/tmp/var# ls
lib lock log openser run snmp spool tmp
root@rome:/tmp/var# cd log
root@rome:/tmp/var/log# ls
[Code]....
