I have one user who doesn't receive a beep when he reaches an internal DN's voicemail. You will hear the attendant say that the person is not available and then the recorded name, but there's never a beep and consequently cannot leave a voicemail.
View 1 RepliesI am using cisco call manager and unity server.one cisco IP phone voice mail password not responding immediately.
View 1 Replies View Relatedremove beep sound when cpu pre-boot assessment build?
View 3 Replies View RelatedSince a few days my WRT120N gives an audio alarm (beep) about every 10 secs. Cannot find how to overcome this or find the root cause. Installed new s/w version. H/W reset. Nothing works.
View 2 Replies View RelatedJust purchased a 3355 and installed, followed the set up no problems, added to WCS. Then WCS says no longer able to be reached.
Unable to ping, have to keep running the setup./opt/mse/setup/setup.sh seems, like the settings are not being kept.
Tried /opt/mse/setup/setup.log and sasys I have no permission, this is when logged in as root.
i am installing a CWLMS 4.0 and everything was good until i have reached the discovery for the devices, i am dealing with a bank setup and the branches is connected using layer 3 MPLS, branches are located behind the ISP router, so as a cdp neighbor i cant see anything but the ISP router at my Core.
so i cant see the branches routers as neighbors to my (seed Device) Core, and i have tried to use the ping sweep and i could not reach them also. and also to add them manually as we were doing before in the earlier versions of CWLMS, using the Devices and Credintials, this option is removed from the LMS 4.0 as i have red in a document.
1- snmp is configured on all devices.
2- access-list is configured on all devices.
3- i am able to reach the LAN Devices without any problems and the configuration is the same on all of the devices.
in windows 7 pro, While trying to join domain xxxx.local, error message appears. even ping xxxx.local is working...
View 4 Replies View RelatedI have a ME-3400EG-12CS-M switch the ports 13 thru 16 have sfp's and are connection to other 3560 switches over fiber. The GIG 0/1 on the 3400 connects to the long haul sonet transport electrically. The IOS is Version 12.2(55)SE3. I can't ping or log into the 3400 unless I am at one of the 3560 switches hanging off of the NNI ports 13 thru 16. I think it is because the max number of NNI ports are 4 and I can't change the GIG 0/1 to a NNI port. Can I make config changes to the UNI port so that it will act like a NNI port with out upgrading the IOS to allow for more NNI ports?
View 1 Replies View RelatedI am trying to setup QuickVPN on my RV180W and having no luck. My client log shows "Remote gateway wasn't reached" "Failed to connect". The client is Win7 64-bit. I have created the firewall rule for icmpv4 on my windows 7 client but still no luck. I checked with my ISP and they say all ports are open. I have created the VPN user.
View 6 Replies View RelatedI am working in an environment with 6 4402 all running 6.0.119.4 code and WCS 6.0.196.0. I keep getting an alert from WCS that the controllers cannot be reached "Controller '10.x.x.x' is unreachable. - Controller Name: 'Name'"
Now when I go to access the WLC through HTTPS I have no access at all but controller still responds to ICMP, HTTP, Telnet, SSH. I know I should have HTTP and Telnet disabled but since HTTPS keeps failing I would have no way to get into the controller. Is this a known issue in the 6.0.199.4 code? should I consider upgrading? The only fix I have found to work is to disable HTTPS reboot controller enable HTTPS and reboot again.
We have a 2960 switch (switch2), whose Management IP cannot be reached/Ping'd. Could not Ping . We have checked the following, but still no clue on the root cause. Haven't tried a reboot yet.
Topology.
All switches are cascaded through trunk and allows all v lan's.
L3switch1 <-> switch1 <-> switch2 <-> switch3 <-> L3switch2
Switch 2 has correct ARP entries for the other switches that we try to ping.Mac address table is fine.Switches other than Switch 2 has proper ARP and Mac entries.This Mgmt v lan is not pruned across any trunks. (we are able to ping switch3 crossing switch2 when tried from switch1)Switches are running PVST and convergence is fine.No access list to deny the traffic.Tried sut/no shut on the V lan interface.
But still switch 2 could not be reached.
I want to be able to send snmp traps to my NMS alerting our NOC to when we reach our configured max-associations on an ap. We currently use both 1130 AG and 1140-2N in autonomous mode, no controller. I have found a debug command "debug dot11 station connection failure" and the output of a test AP shows us the fact that the maximum number was reached. I need to find if it is possible to trap on such information.
View 1 Replies View RelatedI have two Aironet 1242AG access points. Currently, one of those access points is in use with an SSID of ABCWIFI.
I want to extend the wireless network to an area that can't be reached by copper or fiber. So, I've purchased another 1242AG. What I'm not sure of is how to configure it. Should I use it as a repeater or in a root-bridge/non-root bridge configuration?
What I'm most confused about is, what do I do with the second radio? Do I use the 5Ghz as the "backhaul" with a completely separate SSID and then broadcast the normal SSID over the 2.4Ghz? Or, do I even use the second radio at all? The key is that the same SSID is used in all locations because the devices in use need to move seemlessly between access points
We have several site-to-site IPSec VPN's setup.
All are running on ASA's 8.2(1).
All have a Security Association Lifetime (Time) of 8 hours.
All have a Security Association Lifetime (Traffic Volum) of 4608000 KiloBytes.
We have an issue when we do Oracle logshipping between the sites.
This triggers the Traffic Volume rekey as can be seen by this entry in the logs: -
%ASA-7-702307: IPSEC: An inbound L2L SA (SPI= 0x169FA1C1) between and (user= ) is rekeying due to data rollover.
However it does not appear as if the renegotiation is occurring properly. Within 10 to 15 minutes data stops being transmitted along the link, even though the IPSec tunnel still appears up in the ASDM GUI.
The 'fix' for this is that we are using is to login to the ASDM GUI and bounce the link by going to Monitoring => VPN => VPN Statistics => Sessions => IPSec Site-to-Site. Then select the appropriate VPN tunnel and click on 'Logout'. This forces a link renegotiation which works fine.
I have attached a logfile from the local ASA (there's nothing in the logfile of the remote ASA until we bounce the VPN tunnel).
I'm trying to test fast roaming using a Cisco 2100 Series controller and 2 1140 APs. The initial authentication succeeds fine and the wireless connection works ok using WPA2+CCKM and LEAP with a Cisco ACS radius server.The problem is that the client does not attempt to preauthenticate with the other AP because the RSN Capabilities IE in the AP beacons and probe responses do not set the RSN Preauthentication capable bit. I can't figure out what it takes to get the APs to indicate to clients that it can do preauthentication. I'm been crawling through all the documentation I can find, to no avail.
View 1 Replies View RelatedWe are about to share a 10 MBit ISP connection with 2 others companies, and they are going to split the bill up into 3,3 and 4 Mbit, so we where thinking that we could setup a switch before their and ours router and provide them with a static IP from our ISP. But is it possible to set a bandwidth limit on the ports of a Cisco Catalyst 2960-8TC, so that we can set a limit of 3,3 and 4 on 3 ports.
View 1 Replies View RelatedI want to PAT my project of WLAN and i attached the document, how I create the Testing Criteria of the said scenarios, PAT document includes WCS 7.0, WLC 5508, MSE 3310, Cisco AP 3502e and ACS 4.2.
View 0 Replies View RelatedI have cisco ASA5510 firewall using in my network but unable to bolck Url's unwanted. can i block the [URL] on the asa by using regular exp.
View 3 Replies View RelatedI have 7 POE switches that have ESI IP phones attached. I have two VLANS, 1 and 2. VLAN 2 is used for voice and is defined in each switch.The ESI IP phones connect to my POE switch ports and the pc attaches through the ESI IP phone.
I have had voice quality issue between floors in my building. Talking to others on my floor via the IP phone, there are no voice quality issues. [code]
is it possible to connect Cisco Ap-1242AG with non-cisco wireless router to work as repeater?
View 1 Replies View RelatedI am looking at a config on a 5550 FW, and am trying to make sense of the syntax of the following rules. I have been to the Cisco site, but can't find much on the syntax.
View 8 Replies View RelatedI currently use a device called the Access Enforcer which runs OpenBSD. I have 3 stable, working VPN tunnel's where the other side's device is a Cisco ASA 5520 or 5540. I was setting up my 4th VPN where the other side used a Cisco ASA 5520 and ran into issue's. The Cisco side can bring up the tunnel. Once the tunnel is up each side can talk to the other side. However, when the tunnel is dropped, the OpenBSD side cannot bring up the tunnel. The error received is on the OpenBSD device is "isakmpd[29581]: transport_send_messages: giving up on exchange from-XX.X.X.0/24-to-XX.XXX.XXX.240, no response from peer XX.XX.XXX.141:4500". I have been trying to figure this out for weeks now and can't seem to find the cause.
View 3 Replies View RelatedI am trying to configure a 3750G that has been sitting on the shelf for several months and am getting the following error -
% Error: Unable to create flash:/microcode_update% Error: It must not already exist
Normally, getting an error during POST isnt a good thing. My first thought was that flash was corrupted or flagged RO somehow. I did fsck flash: with no change. I next tried fsck /test flash:. It tested 77 blocks and performed 0 erasures. It had been running for about 15 minutes with no problems reported so far. Multiple reboots of the switch still report the same error.
I have reviewed the history of what I have done on this switch and finally think I found the problem. I noticed a microcode_update directory that I am not used to see on a 3750. Deleted the directory using the rmdir command and rebooted the switch. On reboot, I noticed that a front_end/ directory was listed as being created as well as fe_type_1 and fe_type_2 were created. The switch now boots up without any errors.
I have two Cisco Aironets 1401 connected to a Cisco Catalyst 3560 Switch. When users log onto the Wifi the APs authenticate with a Freeradius that then authenticates with LDAP.
Recently users have been getting kicked off of the network but I'm not sure why.If so how do I set these APs to roam with my setupd?For all I know there could be an issue with the switch I'm just not sure where to start when it comes to troubleshooting this issue.
Guys I am using a cisco 2911 router with three interfaces: Gi0/0 connected through a switch to all my servers and Gi0/2 which will connect to another server, and Gi0/1 is my outside interface connecting through a switch to two ISP's.I have webservers and Terminal servers/File Servers with 10.0.0.0 network address connected throught My Gi0/0 interface.Now I want to implement a Cisco Advanced firewall for security on my router using CCP.I want the firewall to work such that it allows external users to access the servers on Gi0/0 through ports 0,23,25,20,21,53, 110,3389. and to access the SIP server on Gi0/2. My issue is can i just create two DMZ's for both interface Gi0/0 and Gi0/2 without creating an inside zone and Gi0/1 as outside zone as my internal traffic is mostly server based and the users connect remotely through terminal server to access resourcess using RDP, secondly how do I open the relevant ports.I have checked alot and all I have seen is just basic process on using the wizard I have no idea how to go about this issue.
View 19 Replies View RelatedI bought a new cisco 3550 switch to prepare for my Cisco certification prepration. Actually i dont know how to connect the cisco switch to a laptop with only usb ports....... earlier i used to do my practise using Cisco packet tracer but i think for CCNP switch that is not enough thats y i bought second hand switch. how can i connect that switch with my toshiba laptop which has only USB ports. do i need to buy some sort of convertor or other hardware. And if so what does u call it and how much does it cost?
View 5 Replies View RelatedI am struggling to have my PPTP traffic to get routed through NAT to reach other Server LAN segment. I am using Cisco 2921 router as a PPTP server.This Cisco 2921 router is working as PPTP server and doing NAT also to reach Server LAN segment (LAN-B).My problem is after PPTP connection establishes I cannot reach any of the LAN segment, but after connecting PPTP I can browse Internet without any issue, but none of the LAN element is reachable. Please have a look on the configuration I am posting 2921 router configuration to suggest something, I have also attached the network setup for better understanding…Just to update Clients in LAN-A can access Internet as well as servers (LAN-B). [code]
View 2 Replies View RelatedI would like to know the IOS which supports :ACL Support for Filtering on TTL Value feature on my Cisco 7600 device. I check on cisco and found the Cisco 12.4T release but this software doesn't fit onto my chasis. which software should I upgrade to on my cisco 7600 to have this feature.
View 5 Replies View RelatedI have a cisco router I would like to reset the password for. Its the first password that is entered. for exampleUser access verificationPassword:I have changed the en password using this command:router(config)#enable secret cisco123 <---example password
View 5 Replies View RelatedI finally got the Site to Site Vpn from our corporate to remote site. Is there a way to connect a cisco phone over that network. Since both Voice Vlans are exempt from acl I would imagine all traffic is clear to go accross? and if so I just have to set the phone to our tftp/ccme. Will that work.
View 2 Replies View RelatedI want to create a user who only has access to "router>" prompt on the CLI. this user should not be able to do enable command and by no other means be able to go to global configuration mode. I know the command router(conf t)# username ABC privilege 1 password ABCPASS, but even with this command, this user gets privilege 15 access.
View 2 Replies View RelatedI have the CISCO 1800 and I have there the HWIC-2T. I have two questions.First is an easy one. I want to replace the HWIC-2T with HWIC-4T but the CISCO 1800 guide and the HWIC-4T guide says that they dont fit together but I inserted the HWIC-4T in to the CISCO 1800 it recognized him with all the 4 Smart Serial ports that it hase. The question is, how can I check if the CISCO 1800 supports the HWIC-4T?Second question is how can I configure one of the Smart Serials in the HWIC-2T/4T to comunicate with the X.25 Protocol? What I have now is at one end CISCO 1800 and at the other end CISCO 2800 and they are comunicating with each other throught one of the Smart Serials they have. I want to connect to each one of then an old pc that comunicate only with X.25 and I want this two computers to comunicate with each other throught those two routers.
View 2 Replies View RelatedWe're currently evaluating Cisco Prime LMS 4.2.Something we've been trying to achieve for the past couple of days is to have LMS notify us when a Microsoft Host is Unreachable, and then to notify us once that alarm has cleared (the Microsoft Host is Reachable again).
We're at the point where the Microsoft Host was discovered, LMS incorrectly identified it as a Cisco Call Manager, so we changed it's identity to non-cisco device > microsoft host > microsoft host. LMS currently has the device listed as being in the 'Questioned' state. SNMP timeout has been set to 15 seconds, and the SNMP community is correct.
Being new to LMS Prime, and having not received any training on the product to this point, we turned to the admin guide, but we couldn't find anything that goes into detail for how to manage the notification for non-Cisco devices.
Is what we're trying to achieve possible with Cisco Prime LMS 4.2? We just want to be able to receive simple 'host unreachable' notifications for Microsoft servers, and the corresponding 'cleared' notifications once the server is back online.